Datasheet

ManualsBrandsNXP SEMICONDUCTORS ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller LQFP 48 (7x7) 8-Bit 8 MHz I/O number 37

161

162

163

164

165

166

167

168

169

170

Table Of Contents

Revision History
List of Chapters
Table of Contents
Chapter 1 General Description
- 1.1 Introduction
- 1.2 Features
  - 1.2.1 Standard Features
  - 1.2.2 Features of the CPU08
- 1.3 MCU Block Diagram
- 1.4 Pin Assignments
- 1.5 Pin Functions
Chapter 2 Memory
- 2.1 Introduction
- 2.2 Unimplemented Memory Locations
- 2.3 Reserved Memory Locations
- 2.4 Input/Output (I/O) Section
- 2.5 Random-Access Memory (RAM)
- 2.6 FLASH-1 Memory (FLASH-1)
- 2.7 FLASH-2 Memory (FLASH-2)
Chapter 3 Analog-to-Digital Converter (ADC)
- 3.1 Introduction
- 3.2 Features
- 3.3 Functional Description
- 3.4 Monotonicity
- 3.5 Interrupts
- 3.6 Low-Power Modes
  - 3.6.1 Wait Mode
  - 3.6.2 Stop Mode
- 3.7 I/O Signals
- 3.8 I/O Registers
Chapter 4 Clock Generator Module (CGM)
- 4.1 Introduction
- 4.2 Features
- 4.3 Functional Description
- 4.4 I/O Signals
- 4.5 CGM Registers
- 4.6 Interrupts
- 4.7 Special Modes
- 4.8 Acquisition/Lock Time Specifications
Chapter 5 Configuration Register (CONFIG)
- 5.1 Introduction
- 5.2 Functional Description
Chapter 6 Computer Operating Properly (COP) Module
- 6.1 Introduction
- 6.2 Functional Description
- 6.3 I/O Signals
- 6.4 COP Control Register
- 6.5 Interrupts
- 6.6 Monitor Mode
- 6.7 Low-Power Modes
  - 6.7.1 Wait Mode
  - 6.7.2 Stop Mode
- 6.8 COP Module During Break Mode
Chapter 7 Central Processor Unit (CPU)
- 7.1 Introduction
- 7.2 Features
- 7.3 CPU Registers
- 7.4 Arithmetic/Logic Unit (ALU)
- 7.5 Low-Power Modes
  - 7.5.1 Wait Mode
  - 7.5.2 Stop Mode
- 7.6 CPU During Break Interrupts
- 7.7 Instruction Set Summary
- 7.8 Opcode Map
Chapter 8 External Interrupt (IRQ)
- 8.1 Introduction
- 8.2 Features
- 8.3 Functional Description
- 8.4 IRQ Pin
- 8.5 IRQ Module During Break Interrupts
- 8.6 IRQ Status and Control Register
Chapter 9 Keyboard Interrupt Module (KBI)
- 9.1 Introduction
- 9.2 Features
- 9.3 Functional Description
- 9.4 Keyboard Initialization
- 9.5 Low-Power Modes
  - 9.5.1 Wait Mode
  - 9.5.2 Stop Mode
- 9.6 Keyboard Module During Break Interrupts
- 9.7 I/O Registers
Chapter 10 Low-Power Modes
- 10.1 Introduction
  - 10.1.1 Wait Mode
  - 10.1.2 Stop Mode
- 10.2 Analog-to-Digital Converter (ADC)
  - 10.2.1 Wait Mode
  - 10.2.2 Stop Mode
- 10.3 Break Module (BRK)
  - 10.3.1 Wait Mode
  - 10.3.2 Stop Mode
- 10.4 Central Processor Unit (CPU)
  - 10.4.1 Wait Mode
  - 10.4.2 Stop Mode
- 10.5 Clock Generator Module (CGM)
  - 10.5.1 Wait Mode
  - 10.5.2 Stop Mode
- 10.6 Computer Operating Properly Module (COP)
  - 10.6.1 Wait Mode
  - 10.6.2 Stop Mode
- 10.7 External Interrupt Module (IRQ)
  - 10.7.1 Wait Mode
  - 10.7.2 Stop Mode
- 10.8 Keyboard Interrupt Module (KBI)
  - 10.8.1 Wait Mode
  - 10.8.2 Stop Mode
- 10.9 Low-Voltage Inhibit Module (LVI)
  - 10.9.1 Wait Mode
  - 10.9.2 Stop Mode
- 10.10 Enhanced Serial Communications Interface Module (ESCI)
  - 10.10.1 Wait Mode
  - 10.10.2 Stop Mode
- 10.11 Serial Peripheral Interface Module (SPI)
  - 10.11.1 Wait Mode
  - 10.11.2 Stop Mode
- 10.12 Timer Interface Module (TIM1 and TIM2)
  - 10.12.1 Wait Mode
  - 10.12.2 Stop Mode
- 10.13 Timebase Module (TBM)
  - 10.13.1 Wait Mode
  - 10.13.2 Stop Mode
- 10.14 Exiting Wait Mode
- 10.15 Exiting Stop Mode
Chapter 11 Low-Voltage Inhibit (LVI)
- 11.1 Introduction
- 11.2 Features
- 11.3 Functional Description
- 11.4 LVI Status Register
- 11.5 LVI Interrupts
- 11.6 Low-Power Modes
  - 11.6.1 Wait Mode
  - 11.6.2 Stop Mode
Chapter 12 Input/Output (I/O) Ports
- 12.1 Introduction
- 12.2 Unused Pin Termination
- 12.3 Port A
- 12.4 Port B
  - 12.4.1 Port B Data Register
  - 12.4.2 Data Direction Register B
- 12.5 Port C
- 12.6 Port D
- 12.7 Port E
  - 12.7.1 Port E Data Register
  - 12.7.2 Data Direction Register E
- 12.8 Port F
  - 12.8.1 Port F Data Register
  - 12.8.2 Data Direction Register F
- 12.9 Port G
  - 12.9.1 Port G Data Register
  - 12.9.2 Data Direction Register G
Chapter 13 Enhanced Serial Communications Interface (ESCI) Module
- 13.1 Introduction
- 13.2 Features
- 13.3 Pin Name Conventions
- 13.4 Functional Description
- 13.5 Low-Power Modes
  - 13.5.1 Wait Mode
  - 13.5.2 Stop Mode
- 13.6 ESCI During Break Module Interrupts
- 13.7 I/O Signals
  - 13.7.1 PTE0/TxD (Transmit Data)
  - 13.7.2 PTE1/RxD (Receive Data)
- 13.8 I/O Registers
- 13.9 ESCI Arbiter
Chapter 14 System Integration Module (SIM)
- 14.1 Introduction
- 14.2 SIM Bus Clock Control and Generation
- 14.3 Reset and System Initialization
  - 14.3.1 External Pin Reset
  - 14.3.2 Active Resets from Internal Sources
- 14.4 SIM Counter
- 14.5 Exception Control
- 14.6 Low-Power Modes
  - 14.6.1 Wait Mode
  - 14.6.2 Stop Mode
- 14.7 SIM Registers
Chapter 15 Serial Peripheral Interface (SPI) Module
- 15.1 Introduction
- 15.2 Features
- 15.3 Functional Description
  - 15.3.1 Master Mode
  - 15.3.2 Slave Mode
- 15.4 Transmission Formats
- 15.5 Queuing Transmission Data
- 15.6 Error Conditions
  - 15.6.1 Overflow Error
  - 15.6.2 Mode Fault Error
- 15.7 Interrupts
- 15.8 Resetting the SPI
- 15.9 Low-Power Modes
  - 15.9.1 Wait Mode
  - 15.9.2 Stop Mode
- 15.10 SPI During Break Interrupts
- 15.11 I/O Signals
- 15.12 I/O Registers
Chapter 16 Timebase Module (TBM)
- 16.1 Introduction
- 16.2 Features
- 16.3 Functional Description
- 16.4 Interrupts
- 16.5 TBM Interrupt Rate
- 16.6 Low-Power Modes
  - 16.6.1 Wait Mode
  - 16.6.2 Stop Mode
- 16.7 Timebase Control Register
Chapter 17 Timer Interface Module (TIM1)
- 17.1 Introduction
- 17.2 Features
- 17.3 Functional Description
- 17.4 Interrupts
- 17.5 Wait Mode
- 17.6 TIM1 During Break Interrupts
- 17.7 Input/Output Signals
- 17.8 Input/Output Registers
Chapter 18 Timer Interface Module (TIM2)
- 18.1 Introduction
- 18.2 Features
- 18.3 Functional Description
- 18.4 Interrupts
- 18.5 Low-Power Modes
  - 18.5.1 Wait Mode
  - 18.5.2 Stop Mode
- 18.6 TIM2 During Break Interrupts
- 18.7 I/O Signals
  - 18.7.1 TIM2 Clock Pin (T2CH0)
  - 18.7.2 TIM2 Channel I/O Pins (T2CH5:T2CH2 and T2CH1:T2CH0)
- 18.8 I/O Registers
Chapter 19 Development Support
- 19.1 Introduction
- 19.2 Break Module (BRK)
- 19.3 Monitor Module (MON)
  - 19.3.1 Functional Description
  - 19.3.2 Security
Chapter 20 Electrical Specifications
- 20.1 Introduction
- 20.2 Absolute Maximum Ratings
- 20.3 Functional Operating Range
- 20.4 Thermal Characteristics
- 20.5 5.0-Vdc Electrical Characteristics
- 20.6 3.3-Vdc Electrical Characteristics
- 20.7 5.0-Volt Control Timing
- 20.8 3.3-Volt Control Timing
- 20.9 Clock Generation Module (CGM) Characteristics
- 20.10 5.0-Volt ADC Characteristics
- 20.11 3.3-Volt ADC Characteristics
- 20.12 5.0-Volt SPI Characteristics
- 20.13 3.3-Volt SPI Characteristics
- 20.14 Timer Interface Module Characteristics
- 20.15 Memory Characteristics
Chapter 21 Ordering Information and Mechanical Specifications
- 21.1 Introduction
- 21.2 MC Order Numbers
- 21.3 Package Dimensions
Appendix A MC68HC908GR48A
- A.1 Introduction
- A.2 Block Diagram
- A.3 Memory
- A.4 Ordering Information
Appendix B MC68HC908GR32A
- B.1 Introduction
- B.2 Block Diagram
- B.3 Memory
- B.4 Ordering Information

Enhanced Serial Communications Interface (ESCI) Module

MC68HC908GR60A • MC68HC908GR48A • MC68HC908GR32A Data Sheet, Rev. 5

168 Freescale Semiconductor

• Enables the transmitter

• Enables the receiver

• Enables ESCI wakeup

• Transmits ESCI break characters

SCTIE — ESCI Transmit Interrupt Enable Bit

This read/write bit enables the SCTE bit to generate ESCI transmitter CPU interrupt requests. Setting

the SCTIE bit in SCC2 enables the SCTE bit to generate CPU interrupt requests. Reset clears the

SCTIE bit.

1 = SCTE enabled to generate CPU interrupt

0 = SCTE not enabled to generate CPU interrupt

TCIE — Transmission Complete Interrupt Enable Bit

This read/write bit enables the TC bit to generate ESCI transmitter CPU interrupt requests. Reset

clears the TCIE bit.

1 = TC enabled to generate CPU interrupt requests

0 = TC not enabled to generate CPU interrupt requests

SCRIE — ESCI Receive Interrupt Enable Bit

This read/write bit enables the SCRF bit to generate ESCI receiver CPU interrupt requests. Setting the

SCRIE bit in SCC2 enables the SCRF bit to generate CPU interrupt requests. Reset clears the

SCRIE bit.

1 = SCRF enabled to generate CPU interrupt

0 = SCRF not enabled to generate CPU interrupt

ILIE — Idle Line Interrupt Enable Bit

This read/write bit enables the IDLE bit to generate ESCI receiver CPU interrupt requests. Reset clears

the ILIE bit.

1 = IDLE enabled to generate CPU interrupt requests

0 = IDLE not enabled to generate CPU interrupt requests

TE — Transmitter Enable Bit

Setting this read/write bit begins the transmission by sending a preamble of 10 or 11 1s from the

transmit shift register to the TxD pin. If software clears the TE bit, the transmitter completes any

transmission in progress before the TxD returns to the idle condition (high). Clearing and then setting

TE during a transmission queues an idle character to be sent after the character currently being

transmitted. Reset clears the TE bit.

1 = Transmitter enabled

0 = Transmitter disabled

NOTE

Writing to the TE bit is not allowed when the enable ESCI bit (ENSCI) is

clear. ENSCI is in ESCI control register 1.

Address: $0014

Bit 7654321Bit 0

Read:

SCTIE TCIE SCRIE ILIE TE RE RWU SBK

Write:

Reset:00000000

Figure 13-11. ESCI Control Register 2 (SCC2)