Datasheet

ManualsBrandsNXP SEMICONDUCTORS ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller LQFP 48 (7x7) 8-Bit 8 MHz I/O number 37

171

172

173

174

175

176

177

178

179

180

Table Of Contents

Revision History
List of Chapters
Table of Contents
Chapter 1 General Description
- 1.1 Introduction
- 1.2 Features
  - 1.2.1 Standard Features
  - 1.2.2 Features of the CPU08
- 1.3 MCU Block Diagram
- 1.4 Pin Assignments
- 1.5 Pin Functions
Chapter 2 Memory
- 2.1 Introduction
- 2.2 Unimplemented Memory Locations
- 2.3 Reserved Memory Locations
- 2.4 Input/Output (I/O) Section
- 2.5 Random-Access Memory (RAM)
- 2.6 FLASH-1 Memory (FLASH-1)
- 2.7 FLASH-2 Memory (FLASH-2)
Chapter 3 Analog-to-Digital Converter (ADC)
- 3.1 Introduction
- 3.2 Features
- 3.3 Functional Description
- 3.4 Monotonicity
- 3.5 Interrupts
- 3.6 Low-Power Modes
  - 3.6.1 Wait Mode
  - 3.6.2 Stop Mode
- 3.7 I/O Signals
- 3.8 I/O Registers
Chapter 4 Clock Generator Module (CGM)
- 4.1 Introduction
- 4.2 Features
- 4.3 Functional Description
- 4.4 I/O Signals
- 4.5 CGM Registers
- 4.6 Interrupts
- 4.7 Special Modes
- 4.8 Acquisition/Lock Time Specifications
Chapter 5 Configuration Register (CONFIG)
- 5.1 Introduction
- 5.2 Functional Description
Chapter 6 Computer Operating Properly (COP) Module
- 6.1 Introduction
- 6.2 Functional Description
- 6.3 I/O Signals
- 6.4 COP Control Register
- 6.5 Interrupts
- 6.6 Monitor Mode
- 6.7 Low-Power Modes
  - 6.7.1 Wait Mode
  - 6.7.2 Stop Mode
- 6.8 COP Module During Break Mode
Chapter 7 Central Processor Unit (CPU)
- 7.1 Introduction
- 7.2 Features
- 7.3 CPU Registers
- 7.4 Arithmetic/Logic Unit (ALU)
- 7.5 Low-Power Modes
  - 7.5.1 Wait Mode
  - 7.5.2 Stop Mode
- 7.6 CPU During Break Interrupts
- 7.7 Instruction Set Summary
- 7.8 Opcode Map
Chapter 8 External Interrupt (IRQ)
- 8.1 Introduction
- 8.2 Features
- 8.3 Functional Description
- 8.4 IRQ Pin
- 8.5 IRQ Module During Break Interrupts
- 8.6 IRQ Status and Control Register
Chapter 9 Keyboard Interrupt Module (KBI)
- 9.1 Introduction
- 9.2 Features
- 9.3 Functional Description
- 9.4 Keyboard Initialization
- 9.5 Low-Power Modes
  - 9.5.1 Wait Mode
  - 9.5.2 Stop Mode
- 9.6 Keyboard Module During Break Interrupts
- 9.7 I/O Registers
Chapter 10 Low-Power Modes
- 10.1 Introduction
  - 10.1.1 Wait Mode
  - 10.1.2 Stop Mode
- 10.2 Analog-to-Digital Converter (ADC)
  - 10.2.1 Wait Mode
  - 10.2.2 Stop Mode
- 10.3 Break Module (BRK)
  - 10.3.1 Wait Mode
  - 10.3.2 Stop Mode
- 10.4 Central Processor Unit (CPU)
  - 10.4.1 Wait Mode
  - 10.4.2 Stop Mode
- 10.5 Clock Generator Module (CGM)
  - 10.5.1 Wait Mode
  - 10.5.2 Stop Mode
- 10.6 Computer Operating Properly Module (COP)
  - 10.6.1 Wait Mode
  - 10.6.2 Stop Mode
- 10.7 External Interrupt Module (IRQ)
  - 10.7.1 Wait Mode
  - 10.7.2 Stop Mode
- 10.8 Keyboard Interrupt Module (KBI)
  - 10.8.1 Wait Mode
  - 10.8.2 Stop Mode
- 10.9 Low-Voltage Inhibit Module (LVI)
  - 10.9.1 Wait Mode
  - 10.9.2 Stop Mode
- 10.10 Enhanced Serial Communications Interface Module (ESCI)
  - 10.10.1 Wait Mode
  - 10.10.2 Stop Mode
- 10.11 Serial Peripheral Interface Module (SPI)
  - 10.11.1 Wait Mode
  - 10.11.2 Stop Mode
- 10.12 Timer Interface Module (TIM1 and TIM2)
  - 10.12.1 Wait Mode
  - 10.12.2 Stop Mode
- 10.13 Timebase Module (TBM)
  - 10.13.1 Wait Mode
  - 10.13.2 Stop Mode
- 10.14 Exiting Wait Mode
- 10.15 Exiting Stop Mode
Chapter 11 Low-Voltage Inhibit (LVI)
- 11.1 Introduction
- 11.2 Features
- 11.3 Functional Description
- 11.4 LVI Status Register
- 11.5 LVI Interrupts
- 11.6 Low-Power Modes
  - 11.6.1 Wait Mode
  - 11.6.2 Stop Mode
Chapter 12 Input/Output (I/O) Ports
- 12.1 Introduction
- 12.2 Unused Pin Termination
- 12.3 Port A
- 12.4 Port B
  - 12.4.1 Port B Data Register
  - 12.4.2 Data Direction Register B
- 12.5 Port C
- 12.6 Port D
- 12.7 Port E
  - 12.7.1 Port E Data Register
  - 12.7.2 Data Direction Register E
- 12.8 Port F
  - 12.8.1 Port F Data Register
  - 12.8.2 Data Direction Register F
- 12.9 Port G
  - 12.9.1 Port G Data Register
  - 12.9.2 Data Direction Register G
Chapter 13 Enhanced Serial Communications Interface (ESCI) Module
- 13.1 Introduction
- 13.2 Features
- 13.3 Pin Name Conventions
- 13.4 Functional Description
- 13.5 Low-Power Modes
  - 13.5.1 Wait Mode
  - 13.5.2 Stop Mode
- 13.6 ESCI During Break Module Interrupts
- 13.7 I/O Signals
  - 13.7.1 PTE0/TxD (Transmit Data)
  - 13.7.2 PTE1/RxD (Receive Data)
- 13.8 I/O Registers
- 13.9 ESCI Arbiter
Chapter 14 System Integration Module (SIM)
- 14.1 Introduction
- 14.2 SIM Bus Clock Control and Generation
- 14.3 Reset and System Initialization
  - 14.3.1 External Pin Reset
  - 14.3.2 Active Resets from Internal Sources
- 14.4 SIM Counter
- 14.5 Exception Control
- 14.6 Low-Power Modes
  - 14.6.1 Wait Mode
  - 14.6.2 Stop Mode
- 14.7 SIM Registers
Chapter 15 Serial Peripheral Interface (SPI) Module
- 15.1 Introduction
- 15.2 Features
- 15.3 Functional Description
  - 15.3.1 Master Mode
  - 15.3.2 Slave Mode
- 15.4 Transmission Formats
- 15.5 Queuing Transmission Data
- 15.6 Error Conditions
  - 15.6.1 Overflow Error
  - 15.6.2 Mode Fault Error
- 15.7 Interrupts
- 15.8 Resetting the SPI
- 15.9 Low-Power Modes
  - 15.9.1 Wait Mode
  - 15.9.2 Stop Mode
- 15.10 SPI During Break Interrupts
- 15.11 I/O Signals
- 15.12 I/O Registers
Chapter 16 Timebase Module (TBM)
- 16.1 Introduction
- 16.2 Features
- 16.3 Functional Description
- 16.4 Interrupts
- 16.5 TBM Interrupt Rate
- 16.6 Low-Power Modes
  - 16.6.1 Wait Mode
  - 16.6.2 Stop Mode
- 16.7 Timebase Control Register
Chapter 17 Timer Interface Module (TIM1)
- 17.1 Introduction
- 17.2 Features
- 17.3 Functional Description
- 17.4 Interrupts
- 17.5 Wait Mode
- 17.6 TIM1 During Break Interrupts
- 17.7 Input/Output Signals
- 17.8 Input/Output Registers
Chapter 18 Timer Interface Module (TIM2)
- 18.1 Introduction
- 18.2 Features
- 18.3 Functional Description
- 18.4 Interrupts
- 18.5 Low-Power Modes
  - 18.5.1 Wait Mode
  - 18.5.2 Stop Mode
- 18.6 TIM2 During Break Interrupts
- 18.7 I/O Signals
  - 18.7.1 TIM2 Clock Pin (T2CH0)
  - 18.7.2 TIM2 Channel I/O Pins (T2CH5:T2CH2 and T2CH1:T2CH0)
- 18.8 I/O Registers
Chapter 19 Development Support
- 19.1 Introduction
- 19.2 Break Module (BRK)
- 19.3 Monitor Module (MON)
  - 19.3.1 Functional Description
  - 19.3.2 Security
Chapter 20 Electrical Specifications
- 20.1 Introduction
- 20.2 Absolute Maximum Ratings
- 20.3 Functional Operating Range
- 20.4 Thermal Characteristics
- 20.5 5.0-Vdc Electrical Characteristics
- 20.6 3.3-Vdc Electrical Characteristics
- 20.7 5.0-Volt Control Timing
- 20.8 3.3-Volt Control Timing
- 20.9 Clock Generation Module (CGM) Characteristics
- 20.10 5.0-Volt ADC Characteristics
- 20.11 3.3-Volt ADC Characteristics
- 20.12 5.0-Volt SPI Characteristics
- 20.13 3.3-Volt SPI Characteristics
- 20.14 Timer Interface Module Characteristics
- 20.15 Memory Characteristics
Chapter 21 Ordering Information and Mechanical Specifications
- 21.1 Introduction
- 21.2 MC Order Numbers
- 21.3 Package Dimensions
Appendix A MC68HC908GR48A
- A.1 Introduction
- A.2 Block Diagram
- A.3 Memory
- A.4 Ordering Information
Appendix B MC68HC908GR32A
- B.1 Introduction
- B.2 Block Diagram
- B.3 Memory
- B.4 Ordering Information

Enhanced Serial Communications Interface (ESCI) Module

MC68HC908GR60A • MC68HC908GR48A • MC68HC908GR32A Data Sheet, Rev. 5

174 Freescale Semiconductor

13.8.7 ESCI Baud Rate Register

The ESCI baud rate register (SCBR) together with the ESCI prescaler register selects the baud rate for

both the receiver and the transmitter.

NOTE

There are two prescalers available to adjust the baud rate. One in the ESCI

baud rate register and one in the ESCI prescaler register.

LINT — LIN Transmit Enable

This read/write bit selects the enhanced ESCI features for the local interconnect network (LIN) protocol

as shown in Table 13-6. Reset clears LINT.

LINR — LIN Receiver Bits

This read/write bit selects the enhanced ESCI features for the local interconnect network (LIN) protocol

as shown in Table 13-6. Reset clears LINR.

In LIN (version 1.2) systems, the master node transmits a break character which will appear as

11.05–14.95 dominant bits to the slave node. A data character of 0x00 sent from the master might

appear as 7.65–10.35 dominant bit times. This is due to the oscillator tolerance requirement that the

slave node must be within ±15% of the master node's oscillator. Since a slave node cannot know if it

is running faster or slower than the master node (prior to synchronization), the LINR bit allows the slave

node to differentiate between a 0x00 character of 10.35 bits and a break character of 11.05 bits. The

break symbol length must be verified in software in any case, but the LINR bit serves as a filter,

preventing false detections of break characters that are really 0x00 data characters.

Address: $0019

Bit 7654321Bit 0

Read:

LINT LINR SCP1 SCP0 R SCR2 SCR1 SCR0

Write:

Reset:00000000

R = Reserved

Figure 13-17. ESCI Baud Rate Register (SCBR)

Table 13-6. ESCI LIN Control Bits

LINT LINR M Functionality

0 0 X Normal ESCI functionality

0 1 0 11-bit break detect enabled for LIN receiver

0 1 1 12-bit break detect enabled for LIN receiver

1 0 0 13-bit generation enabled for LIN transmitter

1 0 1 14-bit generation enabled for LIN transmitter

1 1 0 11-bit break detect/13-bit generation enabled for LIN

1 1 1 12-bit break detect/14-bit generation enabled for LIN