Datasheet

ManualsBrandsNXP SEMICONDUCTORS ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller LQFP 48 (7x7) 8-Bit 8 MHz I/O number 37

201

202

203

204

205

206

207

208

209

210

Table Of Contents

Revision History
List of Chapters
Table of Contents
Chapter 1 General Description
- 1.1 Introduction
- 1.2 Features
  - 1.2.1 Standard Features
  - 1.2.2 Features of the CPU08
- 1.3 MCU Block Diagram
- 1.4 Pin Assignments
- 1.5 Pin Functions
Chapter 2 Memory
- 2.1 Introduction
- 2.2 Unimplemented Memory Locations
- 2.3 Reserved Memory Locations
- 2.4 Input/Output (I/O) Section
- 2.5 Random-Access Memory (RAM)
- 2.6 FLASH-1 Memory (FLASH-1)
- 2.7 FLASH-2 Memory (FLASH-2)
Chapter 3 Analog-to-Digital Converter (ADC)
- 3.1 Introduction
- 3.2 Features
- 3.3 Functional Description
- 3.4 Monotonicity
- 3.5 Interrupts
- 3.6 Low-Power Modes
  - 3.6.1 Wait Mode
  - 3.6.2 Stop Mode
- 3.7 I/O Signals
- 3.8 I/O Registers
Chapter 4 Clock Generator Module (CGM)
- 4.1 Introduction
- 4.2 Features
- 4.3 Functional Description
- 4.4 I/O Signals
- 4.5 CGM Registers
- 4.6 Interrupts
- 4.7 Special Modes
- 4.8 Acquisition/Lock Time Specifications
Chapter 5 Configuration Register (CONFIG)
- 5.1 Introduction
- 5.2 Functional Description
Chapter 6 Computer Operating Properly (COP) Module
- 6.1 Introduction
- 6.2 Functional Description
- 6.3 I/O Signals
- 6.4 COP Control Register
- 6.5 Interrupts
- 6.6 Monitor Mode
- 6.7 Low-Power Modes
  - 6.7.1 Wait Mode
  - 6.7.2 Stop Mode
- 6.8 COP Module During Break Mode
Chapter 7 Central Processor Unit (CPU)
- 7.1 Introduction
- 7.2 Features
- 7.3 CPU Registers
- 7.4 Arithmetic/Logic Unit (ALU)
- 7.5 Low-Power Modes
  - 7.5.1 Wait Mode
  - 7.5.2 Stop Mode
- 7.6 CPU During Break Interrupts
- 7.7 Instruction Set Summary
- 7.8 Opcode Map
Chapter 8 External Interrupt (IRQ)
- 8.1 Introduction
- 8.2 Features
- 8.3 Functional Description
- 8.4 IRQ Pin
- 8.5 IRQ Module During Break Interrupts
- 8.6 IRQ Status and Control Register
Chapter 9 Keyboard Interrupt Module (KBI)
- 9.1 Introduction
- 9.2 Features
- 9.3 Functional Description
- 9.4 Keyboard Initialization
- 9.5 Low-Power Modes
  - 9.5.1 Wait Mode
  - 9.5.2 Stop Mode
- 9.6 Keyboard Module During Break Interrupts
- 9.7 I/O Registers
Chapter 10 Low-Power Modes
- 10.1 Introduction
  - 10.1.1 Wait Mode
  - 10.1.2 Stop Mode
- 10.2 Analog-to-Digital Converter (ADC)
  - 10.2.1 Wait Mode
  - 10.2.2 Stop Mode
- 10.3 Break Module (BRK)
  - 10.3.1 Wait Mode
  - 10.3.2 Stop Mode
- 10.4 Central Processor Unit (CPU)
  - 10.4.1 Wait Mode
  - 10.4.2 Stop Mode
- 10.5 Clock Generator Module (CGM)
  - 10.5.1 Wait Mode
  - 10.5.2 Stop Mode
- 10.6 Computer Operating Properly Module (COP)
  - 10.6.1 Wait Mode
  - 10.6.2 Stop Mode
- 10.7 External Interrupt Module (IRQ)
  - 10.7.1 Wait Mode
  - 10.7.2 Stop Mode
- 10.8 Keyboard Interrupt Module (KBI)
  - 10.8.1 Wait Mode
  - 10.8.2 Stop Mode
- 10.9 Low-Voltage Inhibit Module (LVI)
  - 10.9.1 Wait Mode
  - 10.9.2 Stop Mode
- 10.10 Enhanced Serial Communications Interface Module (ESCI)
  - 10.10.1 Wait Mode
  - 10.10.2 Stop Mode
- 10.11 Serial Peripheral Interface Module (SPI)
  - 10.11.1 Wait Mode
  - 10.11.2 Stop Mode
- 10.12 Timer Interface Module (TIM1 and TIM2)
  - 10.12.1 Wait Mode
  - 10.12.2 Stop Mode
- 10.13 Timebase Module (TBM)
  - 10.13.1 Wait Mode
  - 10.13.2 Stop Mode
- 10.14 Exiting Wait Mode
- 10.15 Exiting Stop Mode
Chapter 11 Low-Voltage Inhibit (LVI)
- 11.1 Introduction
- 11.2 Features
- 11.3 Functional Description
- 11.4 LVI Status Register
- 11.5 LVI Interrupts
- 11.6 Low-Power Modes
  - 11.6.1 Wait Mode
  - 11.6.2 Stop Mode
Chapter 12 Input/Output (I/O) Ports
- 12.1 Introduction
- 12.2 Unused Pin Termination
- 12.3 Port A
- 12.4 Port B
  - 12.4.1 Port B Data Register
  - 12.4.2 Data Direction Register B
- 12.5 Port C
- 12.6 Port D
- 12.7 Port E
  - 12.7.1 Port E Data Register
  - 12.7.2 Data Direction Register E
- 12.8 Port F
  - 12.8.1 Port F Data Register
  - 12.8.2 Data Direction Register F
- 12.9 Port G
  - 12.9.1 Port G Data Register
  - 12.9.2 Data Direction Register G
Chapter 13 Enhanced Serial Communications Interface (ESCI) Module
- 13.1 Introduction
- 13.2 Features
- 13.3 Pin Name Conventions
- 13.4 Functional Description
- 13.5 Low-Power Modes
  - 13.5.1 Wait Mode
  - 13.5.2 Stop Mode
- 13.6 ESCI During Break Module Interrupts
- 13.7 I/O Signals
  - 13.7.1 PTE0/TxD (Transmit Data)
  - 13.7.2 PTE1/RxD (Receive Data)
- 13.8 I/O Registers
- 13.9 ESCI Arbiter
Chapter 14 System Integration Module (SIM)
- 14.1 Introduction
- 14.2 SIM Bus Clock Control and Generation
- 14.3 Reset and System Initialization
  - 14.3.1 External Pin Reset
  - 14.3.2 Active Resets from Internal Sources
- 14.4 SIM Counter
- 14.5 Exception Control
- 14.6 Low-Power Modes
  - 14.6.1 Wait Mode
  - 14.6.2 Stop Mode
- 14.7 SIM Registers
Chapter 15 Serial Peripheral Interface (SPI) Module
- 15.1 Introduction
- 15.2 Features
- 15.3 Functional Description
  - 15.3.1 Master Mode
  - 15.3.2 Slave Mode
- 15.4 Transmission Formats
- 15.5 Queuing Transmission Data
- 15.6 Error Conditions
  - 15.6.1 Overflow Error
  - 15.6.2 Mode Fault Error
- 15.7 Interrupts
- 15.8 Resetting the SPI
- 15.9 Low-Power Modes
  - 15.9.1 Wait Mode
  - 15.9.2 Stop Mode
- 15.10 SPI During Break Interrupts
- 15.11 I/O Signals
- 15.12 I/O Registers
Chapter 16 Timebase Module (TBM)
- 16.1 Introduction
- 16.2 Features
- 16.3 Functional Description
- 16.4 Interrupts
- 16.5 TBM Interrupt Rate
- 16.6 Low-Power Modes
  - 16.6.1 Wait Mode
  - 16.6.2 Stop Mode
- 16.7 Timebase Control Register
Chapter 17 Timer Interface Module (TIM1)
- 17.1 Introduction
- 17.2 Features
- 17.3 Functional Description
- 17.4 Interrupts
- 17.5 Wait Mode
- 17.6 TIM1 During Break Interrupts
- 17.7 Input/Output Signals
- 17.8 Input/Output Registers
Chapter 18 Timer Interface Module (TIM2)
- 18.1 Introduction
- 18.2 Features
- 18.3 Functional Description
- 18.4 Interrupts
- 18.5 Low-Power Modes
  - 18.5.1 Wait Mode
  - 18.5.2 Stop Mode
- 18.6 TIM2 During Break Interrupts
- 18.7 I/O Signals
  - 18.7.1 TIM2 Clock Pin (T2CH0)
  - 18.7.2 TIM2 Channel I/O Pins (T2CH5:T2CH2 and T2CH1:T2CH0)
- 18.8 I/O Registers
Chapter 19 Development Support
- 19.1 Introduction
- 19.2 Break Module (BRK)
- 19.3 Monitor Module (MON)
  - 19.3.1 Functional Description
  - 19.3.2 Security
Chapter 20 Electrical Specifications
- 20.1 Introduction
- 20.2 Absolute Maximum Ratings
- 20.3 Functional Operating Range
- 20.4 Thermal Characteristics
- 20.5 5.0-Vdc Electrical Characteristics
- 20.6 3.3-Vdc Electrical Characteristics
- 20.7 5.0-Volt Control Timing
- 20.8 3.3-Volt Control Timing
- 20.9 Clock Generation Module (CGM) Characteristics
- 20.10 5.0-Volt ADC Characteristics
- 20.11 3.3-Volt ADC Characteristics
- 20.12 5.0-Volt SPI Characteristics
- 20.13 3.3-Volt SPI Characteristics
- 20.14 Timer Interface Module Characteristics
- 20.15 Memory Characteristics
Chapter 21 Ordering Information and Mechanical Specifications
- 21.1 Introduction
- 21.2 MC Order Numbers
- 21.3 Package Dimensions
Appendix A MC68HC908GR48A
- A.1 Introduction
- A.2 Block Diagram
- A.3 Memory
- A.4 Ordering Information
Appendix B MC68HC908GR32A
- B.1 Introduction
- B.2 Block Diagram
- B.3 Memory
- B.4 Ordering Information

Transmission Formats

MC68HC908GR60A • MC68HC908GR48A • MC68HC908GR32A Data Sheet, Rev. 5

Freescale Semiconductor 207

edge. Therefore, the slave uses the first SPSCK edge as a start transmission signal. The SS pin can

remain low between transmissions. This format may be preferable in systems having only one master and

only one slave driving the MISO data line.

Figure 15-7. Transmission Format (CPHA = 1)

When CPHA = 1 for a slave, the first edge of the SPSCK indicates the beginning of the transmission. This

causes the SPI to leave its idle state and begin driving the MISO pin with the MSB of its data. Once the

transmission begins, no new data is allowed into the shift register from the transmit data register.

Therefore, the SPI data register of the slave must be loaded with transmit data before the first edge of

SPSCK. Any data written after the first edge is stored in the transmit data register and transferred to the

shift register after the current transmission.

15.4.4 Transmission Initiation Latency

When the SPI is configured as a master (SPMSTR = 1), writing to the SPDR starts a transmission. CPHA

has no effect on the delay to the start of the transmission, but it does affect the initial state of the SPSCK

signal. When CPHA = 0, the SPSCK signal remains inactive for the first half of the first SPSCK cycle.

When CPHA = 1, the first SPSCK cycle begins with an edge on the SPSCK line from its inactive to its

active level. The SPI clock rate (selected by SPR1:SPR0) affects the delay from the write to SPDR and

the start of the SPI transmission. (See Figure 15-8.) The internal SPI clock in the master is a free-running

derivative of the internal MCU clock. To conserve power, it is enabled only when both the SPE and

SPMSTR bits are set. Since the SPI clock is free-running, it is uncertain where the write to the SPDR

occurs relative to the slower SPSCK. This uncertainty causes the variation in the initiation delay shown

in Figure 15-8. This delay is no longer than a single SPI bit time. That is, the maximum delay is two MCU

bus cycles for DIV2, eight MCU bus cycles for DIV8, 32 MCU bus cycles for DIV32, and 128 MCU bus

cycles for DIV128.

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB

MSB

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB

MSB

12345678

SPSCK CYCLE #

FOR REFERENCE

SPSCK; CPOL = 0

SPSCK; CPOL =1

MOSI

FROM MASTER

MISO

FROM SLAVE

; TO SLAVE

CAPTURE STROBE