Datasheet
Table Of Contents
- Revision History
- List of Chapters
- Table of Contents
- Chapter 1 General Description
- 1.1 Introduction
- 1.2 Features
- 1.3 MCU Block Diagram
- 1.4 Pin Assignments
- 1.5 Pin Functions
- 1.5.1 Power Supply Pins (VDD and VSS)
- 1.5.2 Oscillator Pins (OSC1 and OSC2)
- 1.5.3 External Reset Pin (RST)
- 1.5.4 External Interrupt Pin (IRQ)
- 1.5.5 CGM Power Supply Pins (VDDA and VSSA)
- 1.5.6 External Filter Capacitor Pin (CGMXFC)
- 1.5.7 ADC Power Supply/Reference Pins (VDDAD/VREFH and VSSAD/VREFL)
- 1.5.8 Port A Input/Output (I/O) Pins (PTA7/KBD7/AD15-PTA0/KBD0/AD8)
- 1.5.9 Port B I/O Pins (PTB7/AD7-PTB0/AD0)
- 1.5.10 Port C I/O Pins (PTC6-PTC0)
- 1.5.11 Port D I/O Pins (PTD7/T2CH1-PTD0/SS)
- 1.5.12 Port E I/O Pins (PTE5-PTE2, PTE1/RxD, and PTE0/TxD)
- 1.5.13 Port F I/O Pins (PTF7/T2CH5-PTF0)
- 1.5.14 Port G I/O Pins (PTG7/AD23-PTBG0/AD16)
- 1.5.15 Unused Pin Termination
- Chapter 2 Memory
- 2.1 Introduction
- 2.2 Unimplemented Memory Locations
- 2.3 Reserved Memory Locations
- 2.4 Input/Output (I/O) Section
- 2.5 Random-Access Memory (RAM)
- 2.6 FLASH-1 Memory (FLASH-1)
- 2.7 FLASH-2 Memory (FLASH-2)
- Chapter 3 Analog-to-Digital Converter (ADC)
- Chapter 4 Clock Generator Module (CGM)
- 4.1 Introduction
- 4.2 Features
- 4.3 Functional Description
- 4.4 I/O Signals
- 4.4.1 Crystal Amplifier Input Pin (OSC1)
- 4.4.2 Crystal Amplifier Output Pin (OSC2)
- 4.4.3 External Filter Capacitor Pin (CGMXFC)
- 4.4.4 PLL Analog Power Pin (Vdda)
- 4.4.5 PLL Analog Ground Pin (Vssa)
- 4.4.6 Oscillator Enable Signal (SIMOSCEN)
- 4.4.7 Oscillator Enable in Stop Mode Bit (OSCENINSTOP)
- 4.4.8 Crystal Output Frequency Signal (CGMXCLK)
- 4.4.9 CGM Base Clock Output (CGMOUT)
- 4.4.10 CGM CPU Interrupt (CGMINT)
- 4.5 CGM Registers
- 4.6 Interrupts
- 4.7 Special Modes
- 4.8 Acquisition/Lock Time Specifications
- Chapter 5 Configuration Register (CONFIG)
- Chapter 6 Computer Operating Properly (COP) Module
- Chapter 7 Central Processor Unit (CPU)
- Chapter 8 External Interrupt (IRQ)
- Chapter 9 Keyboard Interrupt Module (KBI)
- Chapter 10 Low-Power Modes
- 10.1 Introduction
- 10.2 Analog-to-Digital Converter (ADC)
- 10.3 Break Module (BRK)
- 10.4 Central Processor Unit (CPU)
- 10.5 Clock Generator Module (CGM)
- 10.6 Computer Operating Properly Module (COP)
- 10.7 External Interrupt Module (IRQ)
- 10.8 Keyboard Interrupt Module (KBI)
- 10.9 Low-Voltage Inhibit Module (LVI)
- 10.10 Enhanced Serial Communications Interface Module (ESCI)
- 10.11 Serial Peripheral Interface Module (SPI)
- 10.12 Timer Interface Module (TIM1 and TIM2)
- 10.13 Timebase Module (TBM)
- 10.14 Exiting Wait Mode
- 10.15 Exiting Stop Mode
- Chapter 11 Low-Voltage Inhibit (LVI)
- Chapter 12 Input/Output (I/O) Ports
- Chapter 13 Enhanced Serial Communications Interface (ESCI) Module
- Chapter 14 System Integration Module (SIM)
- Chapter 15 Serial Peripheral Interface (SPI) Module
- Chapter 16 Timebase Module (TBM)
- Chapter 17 Timer Interface Module (TIM1)
- Chapter 18 Timer Interface Module (TIM2)
- Chapter 19 Development Support
- Chapter 20 Electrical Specifications
- 20.1 Introduction
- 20.2 Absolute Maximum Ratings
- 20.3 Functional Operating Range
- 20.4 Thermal Characteristics
- 20.5 5.0-Vdc Electrical Characteristics
- 20.6 3.3-Vdc Electrical Characteristics
- 20.7 5.0-Volt Control Timing
- 20.8 3.3-Volt Control Timing
- 20.9 Clock Generation Module (CGM) Characteristics
- 20.10 5.0-Volt ADC Characteristics
- 20.11 3.3-Volt ADC Characteristics
- 20.12 5.0-Volt SPI Characteristics
- 20.13 3.3-Volt SPI Characteristics
- 20.14 Timer Interface Module Characteristics
- 20.15 Memory Characteristics
- Chapter 21 Ordering Information and Mechanical Specifications
- Appendix A MC68HC908GR48A
- Appendix B MC68HC908GR32A
Timebase Module (TBM)
MC68HC908GR60A • MC68HC908GR48A • MC68HC908GR32A Data Sheet, Rev. 5
224 Freescale Semiconductor
16.7 Timebase Control Register
The timebase has one register, the timebase control register (TBCR), which is used to enable the
timebase interrupts and set the rate.
TBIF — Timebase Interrupt Flag
This read-only flag bit is set when the timebase counter has rolled over.
1 = Timebase interrupt pending
0 = Timebase interrupt not pending
TBR2–TBR0 — Timebase Divider Selection Bits
These read/write bits select the tap in the counter to be used for timebase interrupts as shown in
Table 16-1.
NOTE
Do not change TBR2–TBR0 bits while the timebase is enabled (TBON = 1).
TACK— Timebase Acknowledge Bit
The TACK bit is a write-only bit and always reads as 0. Writing a 1 to this bit clears TBIF, the timebase
interrupt flag bit. Writing a 0 to this bit has no effect.
1 = Clear timebase interrupt flag
0 = No effect
TBIE — Timebase Interrupt Enabled Bit
This read/write bit enables the timebase interrupt when the TBIF bit becomes set. Reset clears the
TBIE bit.
1 = Timebase interrupt is enabled.
0 = Timebase interrupt is disabled.
TBON — Timebase Enabled Bit
This read/write bit enables the timebase. Timebase may be turned off to reduce power consumption
when its function is not necessary. The counter can be initialized by clearing and then setting this bit.
Reset clears the TBON bit.
1 = Timebase is enabled.
0 = Timebase is disabled and the counter initialized to 0s.
Address: $001C
Bit 7654321Bit 0
Read: TBIF
TBR2 TBR1 TBR0
0
TBIE TBON R
Write:
TACK
Reset:00000000
= Unimplemented R = Reserved
Figure 16-2. Timebase Control Register (TBCR)