Datasheet
Table Of Contents
- Revision History
- List of Chapters
- Table of Contents
- Chapter 1 General Description
- 1.1 Introduction
- 1.2 Features
- 1.3 MCU Block Diagram
- 1.4 Pin Assignments
- 1.5 Pin Functions
- 1.5.1 Power Supply Pins (VDD and VSS)
- 1.5.2 Oscillator Pins (OSC1 and OSC2)
- 1.5.3 External Reset Pin (RST)
- 1.5.4 External Interrupt Pin (IRQ)
- 1.5.5 CGM Power Supply Pins (VDDA and VSSA)
- 1.5.6 External Filter Capacitor Pin (CGMXFC)
- 1.5.7 ADC Power Supply/Reference Pins (VDDAD/VREFH and VSSAD/VREFL)
- 1.5.8 Port A Input/Output (I/O) Pins (PTA7/KBD7/AD15-PTA0/KBD0/AD8)
- 1.5.9 Port B I/O Pins (PTB7/AD7-PTB0/AD0)
- 1.5.10 Port C I/O Pins (PTC6-PTC0)
- 1.5.11 Port D I/O Pins (PTD7/T2CH1-PTD0/SS)
- 1.5.12 Port E I/O Pins (PTE5-PTE2, PTE1/RxD, and PTE0/TxD)
- 1.5.13 Port F I/O Pins (PTF7/T2CH5-PTF0)
- 1.5.14 Port G I/O Pins (PTG7/AD23-PTBG0/AD16)
- 1.5.15 Unused Pin Termination
- Chapter 2 Memory
- 2.1 Introduction
- 2.2 Unimplemented Memory Locations
- 2.3 Reserved Memory Locations
- 2.4 Input/Output (I/O) Section
- 2.5 Random-Access Memory (RAM)
- 2.6 FLASH-1 Memory (FLASH-1)
- 2.7 FLASH-2 Memory (FLASH-2)
- Chapter 3 Analog-to-Digital Converter (ADC)
- Chapter 4 Clock Generator Module (CGM)
- 4.1 Introduction
- 4.2 Features
- 4.3 Functional Description
- 4.4 I/O Signals
- 4.4.1 Crystal Amplifier Input Pin (OSC1)
- 4.4.2 Crystal Amplifier Output Pin (OSC2)
- 4.4.3 External Filter Capacitor Pin (CGMXFC)
- 4.4.4 PLL Analog Power Pin (Vdda)
- 4.4.5 PLL Analog Ground Pin (Vssa)
- 4.4.6 Oscillator Enable Signal (SIMOSCEN)
- 4.4.7 Oscillator Enable in Stop Mode Bit (OSCENINSTOP)
- 4.4.8 Crystal Output Frequency Signal (CGMXCLK)
- 4.4.9 CGM Base Clock Output (CGMOUT)
- 4.4.10 CGM CPU Interrupt (CGMINT)
- 4.5 CGM Registers
- 4.6 Interrupts
- 4.7 Special Modes
- 4.8 Acquisition/Lock Time Specifications
- Chapter 5 Configuration Register (CONFIG)
- Chapter 6 Computer Operating Properly (COP) Module
- Chapter 7 Central Processor Unit (CPU)
- Chapter 8 External Interrupt (IRQ)
- Chapter 9 Keyboard Interrupt Module (KBI)
- Chapter 10 Low-Power Modes
- 10.1 Introduction
- 10.2 Analog-to-Digital Converter (ADC)
- 10.3 Break Module (BRK)
- 10.4 Central Processor Unit (CPU)
- 10.5 Clock Generator Module (CGM)
- 10.6 Computer Operating Properly Module (COP)
- 10.7 External Interrupt Module (IRQ)
- 10.8 Keyboard Interrupt Module (KBI)
- 10.9 Low-Voltage Inhibit Module (LVI)
- 10.10 Enhanced Serial Communications Interface Module (ESCI)
- 10.11 Serial Peripheral Interface Module (SPI)
- 10.12 Timer Interface Module (TIM1 and TIM2)
- 10.13 Timebase Module (TBM)
- 10.14 Exiting Wait Mode
- 10.15 Exiting Stop Mode
- Chapter 11 Low-Voltage Inhibit (LVI)
- Chapter 12 Input/Output (I/O) Ports
- Chapter 13 Enhanced Serial Communications Interface (ESCI) Module
- Chapter 14 System Integration Module (SIM)
- Chapter 15 Serial Peripheral Interface (SPI) Module
- Chapter 16 Timebase Module (TBM)
- Chapter 17 Timer Interface Module (TIM1)
- Chapter 18 Timer Interface Module (TIM2)
- Chapter 19 Development Support
- Chapter 20 Electrical Specifications
- 20.1 Introduction
- 20.2 Absolute Maximum Ratings
- 20.3 Functional Operating Range
- 20.4 Thermal Characteristics
- 20.5 5.0-Vdc Electrical Characteristics
- 20.6 3.3-Vdc Electrical Characteristics
- 20.7 5.0-Volt Control Timing
- 20.8 3.3-Volt Control Timing
- 20.9 Clock Generation Module (CGM) Characteristics
- 20.10 5.0-Volt ADC Characteristics
- 20.11 3.3-Volt ADC Characteristics
- 20.12 5.0-Volt SPI Characteristics
- 20.13 3.3-Volt SPI Characteristics
- 20.14 Timer Interface Module Characteristics
- 20.15 Memory Characteristics
- Chapter 21 Ordering Information and Mechanical Specifications
- Appendix A MC68HC908GR48A
- Appendix B MC68HC908GR32A
Timer Interface Module (TIM1)
MC68HC908GR60A • MC68HC908GR48A • MC68HC908GR32A Data Sheet, Rev. 5
234 Freescale Semiconductor
TOF — TIM1 Overflow Flag Bit
This read/write flag is set when the TIM1 counter reaches the modulo value programmed in the TIM1
counter modulo registers. Clear TOF by reading the TIM1 status and control register when TOF is set
and then writing a 0 to TOF. If another TIM1 overflow occurs before the clearing sequence is complete,
then writing 0 to TOF has no effect. Therefore, a TOF interrupt request cannot be lost due to
inadvertent clearing of TOF. Reset clears the TOF bit. Writing a 1 to TOF has no effect.
1 = TIM1 counter has reached modulo value
0 = TIM1 counter has not reached modulo value
TOIE — TIM1 Overflow Interrupt Enable Bit
This read/write bit enables TIM1 overflow interrupts when the TOF bit becomes set. Reset clears the
TOIE bit.
1 = TIM1 overflow interrupts enabled
0 = TIM1 overflow interrupts disabled
TSTOP — TIM1 Stop Bit
This read/write bit stops the TIM1 counter. Counting resumes when TSTOP is cleared. Reset sets the
TSTOP bit, stopping the TIM1 counter until software clears the TSTOP bit.
1 = TIM1 counter stopped
0 = TIM1 counter active
NOTE
Do not set the TSTOP bit before entering wait mode if the TIM1 is required
to exit wait mode. Also, when the TSTOP bit is set and the timer is
configured for input capture operation, input captures are inhibited until the
TSTOP bit is cleared.
TRST — TIM1 Reset Bit
Setting this write-only bit resets the TIM1 counter and the TIM1 prescaler. Setting TRST has no effect
on any other registers. Counting resumes from $0000. TRST is cleared automatically after the TIM1
counter is reset and always reads as 0. Reset clears the TRST bit.
1 = Prescaler and TIM1 counter cleared
0 = No effect
NOTE
Setting the TSTOP and TRST bits simultaneously stops the TIM1 counter
at a value of $0000.
Address: $0020
Bit 7654321Bit 0
Read: TOF
TOIE TSTOP
00
PS2 PS1 PS0
Write: 0 TRST
Reset:00100000
= Unimplemented
Figure 17-5. TIM1 Status and Control Register (T1SC)