Datasheet
Table Of Contents
- Revision History
- List of Chapters
- Table of Contents
- Chapter 1 General Description
- 1.1 Introduction
- 1.2 Features
- 1.3 MCU Block Diagram
- 1.4 Pin Assignments
- 1.5 Pin Functions
- 1.5.1 Power Supply Pins (VDD and VSS)
- 1.5.2 Oscillator Pins (OSC1 and OSC2)
- 1.5.3 External Reset Pin (RST)
- 1.5.4 External Interrupt Pin (IRQ)
- 1.5.5 CGM Power Supply Pins (VDDA and VSSA)
- 1.5.6 External Filter Capacitor Pin (CGMXFC)
- 1.5.7 ADC Power Supply/Reference Pins (VDDAD/VREFH and VSSAD/VREFL)
- 1.5.8 Port A Input/Output (I/O) Pins (PTA7/KBD7/AD15-PTA0/KBD0/AD8)
- 1.5.9 Port B I/O Pins (PTB7/AD7-PTB0/AD0)
- 1.5.10 Port C I/O Pins (PTC6-PTC0)
- 1.5.11 Port D I/O Pins (PTD7/T2CH1-PTD0/SS)
- 1.5.12 Port E I/O Pins (PTE5-PTE2, PTE1/RxD, and PTE0/TxD)
- 1.5.13 Port F I/O Pins (PTF7/T2CH5-PTF0)
- 1.5.14 Port G I/O Pins (PTG7/AD23-PTBG0/AD16)
- 1.5.15 Unused Pin Termination
- Chapter 2 Memory
- 2.1 Introduction
- 2.2 Unimplemented Memory Locations
- 2.3 Reserved Memory Locations
- 2.4 Input/Output (I/O) Section
- 2.5 Random-Access Memory (RAM)
- 2.6 FLASH-1 Memory (FLASH-1)
- 2.7 FLASH-2 Memory (FLASH-2)
- Chapter 3 Analog-to-Digital Converter (ADC)
- Chapter 4 Clock Generator Module (CGM)
- 4.1 Introduction
- 4.2 Features
- 4.3 Functional Description
- 4.4 I/O Signals
- 4.4.1 Crystal Amplifier Input Pin (OSC1)
- 4.4.2 Crystal Amplifier Output Pin (OSC2)
- 4.4.3 External Filter Capacitor Pin (CGMXFC)
- 4.4.4 PLL Analog Power Pin (Vdda)
- 4.4.5 PLL Analog Ground Pin (Vssa)
- 4.4.6 Oscillator Enable Signal (SIMOSCEN)
- 4.4.7 Oscillator Enable in Stop Mode Bit (OSCENINSTOP)
- 4.4.8 Crystal Output Frequency Signal (CGMXCLK)
- 4.4.9 CGM Base Clock Output (CGMOUT)
- 4.4.10 CGM CPU Interrupt (CGMINT)
- 4.5 CGM Registers
- 4.6 Interrupts
- 4.7 Special Modes
- 4.8 Acquisition/Lock Time Specifications
- Chapter 5 Configuration Register (CONFIG)
- Chapter 6 Computer Operating Properly (COP) Module
- Chapter 7 Central Processor Unit (CPU)
- Chapter 8 External Interrupt (IRQ)
- Chapter 9 Keyboard Interrupt Module (KBI)
- Chapter 10 Low-Power Modes
- 10.1 Introduction
- 10.2 Analog-to-Digital Converter (ADC)
- 10.3 Break Module (BRK)
- 10.4 Central Processor Unit (CPU)
- 10.5 Clock Generator Module (CGM)
- 10.6 Computer Operating Properly Module (COP)
- 10.7 External Interrupt Module (IRQ)
- 10.8 Keyboard Interrupt Module (KBI)
- 10.9 Low-Voltage Inhibit Module (LVI)
- 10.10 Enhanced Serial Communications Interface Module (ESCI)
- 10.11 Serial Peripheral Interface Module (SPI)
- 10.12 Timer Interface Module (TIM1 and TIM2)
- 10.13 Timebase Module (TBM)
- 10.14 Exiting Wait Mode
- 10.15 Exiting Stop Mode
- Chapter 11 Low-Voltage Inhibit (LVI)
- Chapter 12 Input/Output (I/O) Ports
- Chapter 13 Enhanced Serial Communications Interface (ESCI) Module
- Chapter 14 System Integration Module (SIM)
- Chapter 15 Serial Peripheral Interface (SPI) Module
- Chapter 16 Timebase Module (TBM)
- Chapter 17 Timer Interface Module (TIM1)
- Chapter 18 Timer Interface Module (TIM2)
- Chapter 19 Development Support
- Chapter 20 Electrical Specifications
- 20.1 Introduction
- 20.2 Absolute Maximum Ratings
- 20.3 Functional Operating Range
- 20.4 Thermal Characteristics
- 20.5 5.0-Vdc Electrical Characteristics
- 20.6 3.3-Vdc Electrical Characteristics
- 20.7 5.0-Volt Control Timing
- 20.8 3.3-Volt Control Timing
- 20.9 Clock Generation Module (CGM) Characteristics
- 20.10 5.0-Volt ADC Characteristics
- 20.11 3.3-Volt ADC Characteristics
- 20.12 5.0-Volt SPI Characteristics
- 20.13 3.3-Volt SPI Characteristics
- 20.14 Timer Interface Module Characteristics
- 20.15 Memory Characteristics
- Chapter 21 Ordering Information and Mechanical Specifications
- Appendix A MC68HC908GR48A
- Appendix B MC68HC908GR32A
I/O Signals
MC68HC908GR60A • MC68HC908GR48A • MC68HC908GR32A Data Sheet, Rev. 5
Freescale Semiconductor 79
4.4.1 Crystal Amplifier Input Pin (OSC1)
The OSC1 pin is an input to the crystal oscillator amplifier.
4.4.2 Crystal Amplifier Output Pin (OSC2)
The OSC2 pin is the output of the crystal oscillator inverting amplifier.
4.4.3 External Filter Capacitor Pin (CGMXFC)
The CGMXFC pin is required by the loop filter to filter out phase corrections. An external filter network is
connected to this pin. (See Figure 4-2.)
NOTE
To prevent noise problems, the filter network should be placed as close to
the CGMXFC pin as possible, with minimum routing distances and no
routing of other signals across the network.
4.4.4 PLL Analog Power Pin (V
DDA
)
V
DDA
is a power pin used by the analog portions of the PLL. Connect the V
DDA
pin to the same voltage
potential as the V
DD
pin.
NOTE
Route V
DDA
carefully for maximum noise immunity and place bypass
capacitors as close as possible to the package.
4.4.5 PLL Analog Ground Pin (V
SSA
)
V
SSA
is a ground pin used by the analog portions of the PLL. Connect the V
SSA
pin to the same voltage
potential as the V
SS
pin.
NOTE
Route V
SSA
carefully for maximum noise immunity and place bypass
capacitors as close as possible to the package.
4.4.6 Oscillator Enable Signal (SIMOSCEN)
The SIMOSCEN signal comes from the system integration module (SIM) and enables the oscillator and
PLL.
4.4.7 Oscillator Enable in Stop Mode Bit (OSCENINSTOP)
OSCENINSTOP is a bit in the CONFIG2 register that enables the oscillator to continue operating during
stop mode. If this bit is set, the oscillator continues running during stop mode. If this bit is not set (default),
the oscillator is controlled by the SIMOSCEN signal which will disable the oscillator during stop mode.
4.4.8 Crystal Output Frequency Signal (CGMXCLK)
CGMXCLK is the crystal oscillator output signal. It runs at the full speed of the crystal (f
XCLK
) and comes
directly from the crystal oscillator circuit. Figure 4-2 shows only the logical relation of CGMXCLK to OSC1
and OSC2 and may not represent the actual circuitry. The duty cycle of CGMXCLK is unknown and may
depend on the crystal and other external factors. Also, the frequency and amplitude of CGMXCLK can be
unstable at start up.