Datasheet

HCS08 CORE
POWER MANAGEMENT
16-CH 12-BIT
ANALOG-TO-DIGITAL
CONVERTER(ADC)
CYCLIC REDUNDANCY
CHECK (CRC)
(RTC)
REAL-TIME COUNTER
(ACMP)
ANALOG COMPARATOR
CIRCUIT(IIC)
INTER-INTEGRATED
INTERFACE MODULE(SPI1)
16-BIT SERIAL PERIPHERAL
INTERFACE MODULE(SPI0)
8-BIT SERIAL PERIPHERAL
INTERFACE (SCI2)
SERIAL COMMUNICATION
INTERFACE (SCI1)
SERIAL COMMUNICATION
INTERFACE (SCI0)
SERIAL COMMUNICATION
MODULE (FTM2)
6-CH FTM TIMER
MODULE (FTM1)
2-CH FLEX TIMER
MODULE (FTM0)
2-CH FLEX TIMER
(MTIM1)
8-BIT MODULO TIMER
8-BIT MODULO TIMER
(MTIM0)
MODULE (KBI1)
KBYBOARD INTERRUPT
MODULE (KBI0)
KEYBOARD INTERRUPT
PTA1/KBI0P1/FTM0CH1/ACMP1/ADP1
PTA3/KBI0P3/TxD0/SCL
PTA4/ACMPO/BKGD/MS
PTA5/IRQ/TCLK0/RESET
PTA6/FTM2FAULT1/ADP2
PTA7/FTM2FAULT2/ADP3
PTB0/KBI0P4/RxD0/ADP4
PTB1/KBI0P5/TxD0/ADP5
PTB2/KBI0P6/SPSCK0/ADP6
PTB3/KBI0P7/MOSI0/ADP7
PTB4/FTM2CH4/MISO0
PTB5/FTM2CH5/SS0
PTB6/SDA/XTAL
PTB7/SCL/EXTAL
PTC0/FTM2CH0/ADP8
PTC1/FTM2CH1/ADP9/
PTC2/FTM2CH2/ADP10
PTC4/FTM1CH0/RTCO
PTC5/FTM1CH1
PTC3/FTM2CH3/ADP11
PTC6/RxD1
PTC7/TxD1
PTD0/KBI1P0/FTM2CH2/SPSCK1
PTD1/KBI1P1/FTM2CH3/MOSI1
PTD2/KBI1P2/MISO1
PTD3/KBI1P3/SS1
PTD4/KBI1P4
PTD5/KBI1P5
PTD6/KBI1P6/RxD2
PTD7/KBI1P7/TxD2
PTE1/MOSI0
PTE2/MISO0
PTE3/SS0
PTE4
PTE5
PTE6
PTE7/TCLK2
PTF0
PTF1
PTF2
PTF3
PTF4/ADP12
PTF5/ADP13
PTF6/ADP14
PTF7/ADP15
PTG0
PTG1
PTG2
PTG3
PTH0/FTM2CH0
PTH1/FTM2CH1
PTH2/BUSOUT
PTH6
PTH7
PTE0/SPSCK0/TCLK1
PTA2/KBI0P2/RxD0/SDA
PTA0/KBI0P0/FTM0CH0/ACMP0/ADP0
20 MHz INTERNAL CLOCK
SOURCE (ICS)
EXTERNAL OSCILLATOR
SOURCE (XOSC)
Port A
LVD
1 kHz OSC
WDOG
SS
V
SS
V
REFH
V
REFL
V
DDA
V
SSA
IRQ
XTAL
EXTAL
V
V
V
DD
CPU
BDC
CONTROLLER(IPC)
INTERRUPT PRIORITY
ON-CHIP ICE AND
DEBUG MODUE (DBG)
Port BPort CPort DPort EPort F
USER EEPROM
Port GPort H
USER RAM
CONTROLLER (PMC)
V
SS
DD
MC9S08PA60 = 4,096 bytes
MC9S08PA32 = 4,096 bytes
MC9S08PA60 = 256 bytes
USER FLASH
MC9S08PA32 = 32,768 bytes
MC9S08PA60 = 60,864 bytes
MODULE (
SIM)
SYSTEM INTEGRATION
MC9S08PA32 = 256 bytes
4
2
3
3
3
3
3
3
3
3
5
5
5
1. PTA2 and PTA3 operate as true open drain when working as output .
3. PTB4, PTB5, PTD0, PTD1, PTE0, PTE1, PTH0 and PTH1 can provide high sink/source current drive.
in 32-pin packages.
4. The frequency of the clock from BUSOUT must be equal or less than 10 MHz with 25 pF loading at PAD.
2. PTA4/ACMPO/BKGD/MS is an output-only pin when used as port pin.
5. The secondary power pair of V and V (pin 41 and pin 40 in 64-pin packages) and the third V (pin 13 in 64-pin packages) are not bonded
DD
SS
SS
1
1
Figure 9-1. Device block diagram highlighting clock modules and pins
Chapter 9 Chip configurations
MC9S08PA60 Reference Manual, Rev. 1, 9/2012
Freescale Semiconductor, Inc. 223