Datasheet
Table Of Contents
- MC9S08SH8DS_Readme
- MC9S08SH8_DSAD_Rev.1
- MC9S08SH8
- Chapter 1 Device Overview
- Chapter 2 Pins and Connections
- Chapter 3 Modes of Operation
- Chapter 4 Memory
- Chapter 5 Resets, Interrupts, and General System Control
- 5.1 Introduction
- 5.2 Features
- 5.3 MCU Reset
- 5.4 Computer Operating Properly (COP) Watchdog
- 5.5 Interrupts
- 5.6 Low-Voltage Detect (LVD) System
- 5.7 Reset, Interrupt, and System Control Registers and Control Bits
- 5.7.1 Interrupt Pin Request Status and Control Register (IRQSC)
- 5.7.2 System Reset Status Register (SRS)
- 5.7.3 System Background Debug Force Reset Register (SBDFR)
- 5.7.4 System Options Register 1 (SOPT1)
- 5.7.5 System Options Register 2 (SOPT2)
- 5.7.6 System Device Identification Register (SDIDH, SDIDL)
- 5.7.7 System Power Management Status and Control 1 Register (SPMSC1)
- 5.7.8 System Power Management Status and Control 2 Register (SPMSC2)
- Chapter 6 Parallel Input/Output Control
- 6.1 Port Data and Data Direction
- 6.2 Pull-up, Slew Rate, and Drive Strength
- 6.3 Ganged Output
- 6.4 Pin Interrupts
- 6.5 Pin Behavior in Stop Modes
- 6.6 Parallel I/O and Pin Control Registers
- 6.6.1 Port A Registers
- 6.6.1.1 Port A Data Register (PTAD)
- 6.6.1.2 Port A Data Direction Register (PTADD)
- 6.6.1.3 Port A Pull Enable Register (PTAPE)
- 6.6.1.4 Port A Slew Rate Enable Register (PTASE)
- 6.6.1.5 Port A Drive Strength Selection Register (PTADS)
- 6.6.1.6 Port A Interrupt Status and Control Register (PTASC)
- 6.6.1.7 Port A Interrupt Pin Select Register (PTAPS)
- 6.6.1.8 Port A Interrupt Edge Select Register (PTAES)
- 6.6.2 Port B Registers
- 6.6.2.1 Port B Data Register (PTBD)
- 6.6.2.2 Port B Data Direction Register (PTBDD)
- 6.6.2.3 Port B Pull Enable Register (PTBPE)
- 6.6.2.4 Port B Slew Rate Enable Register (PTBSE)
- 6.6.2.5 Port B Drive Strength Selection Register (PTBDS)
- 6.6.2.6 Port B Interrupt Status and Control Register (PTBSC)
- 6.6.2.7 Port B Interrupt Pin Select Register (PTBPS)
- 6.6.2.8 Port B Interrupt Edge Select Register (PTBES)
- 6.6.3 Port C Registers
- 6.6.1 Port A Registers
- Chapter 7 Central Processor Unit (S08CPUV2)
- 7.1 Introduction
- 7.2 Programmer’s Model and CPU Registers
- 7.3 Addressing Modes
- 7.4 Special Operations
- 7.5 HCS08 Instruction Set Summary
- Chapter 8 Analog Comparator 5-V (S08ACMPV2)
- Chapter 9 Analog-to-Digital Converter (S08ADCV1)
- 9.1 Introduction
- 9.2 External Signal Description
- 9.3 Register Definition
- 9.3.1 Status and Control Register 1 (ADCSC1)
- 9.3.2 Status and Control Register 2 (ADCSC2)
- 9.3.3 Data Result High Register (ADCRH)
- 9.3.4 Data Result Low Register (ADCRL)
- 9.3.5 Compare Value High Register (ADCCVH)
- 9.3.6 Compare Value Low Register (ADCCVL)
- 9.3.7 Configuration Register (ADCCFG)
- 9.3.8 Pin Control 1 Register (APCTL1)
- 9.3.9 Pin Control 2 Register (APCTL2)
- 9.3.10 Pin Control 3 Register (APCTL3)
- 9.4 Functional Description
- 9.5 Initialization Information
- 9.6 Application Information
- Chapter 10 Internal Clock Source (S08ICSV2)
- 10.1 Introduction
- 10.2 External Signal Description
- 10.3 Register Definition
- 10.4 Functional Description
- Chapter 11 Inter-Integrated Circuit (S08IICV2)
- Chapter 12 Modulo Timer (S08MTIMV1)
- Chapter 13 Real-Time Counter (S08RTCV1)
- Chapter 14 Serial Communications Interface (S08SCIV4)
- Chapter 15 Serial Peripheral Interface (S08SPIV3)
- Chapter 16 Timer Pulse-Width Modulator (S08TPMV3)
- Chapter 17 Development Support
- 17.1 Introduction
- 17.2 Background Debug Controller (BDC)
- 17.3 On-Chip Debug System (DBG)
- 17.4 Register Definition
- 17.4.1 BDC Registers and Control Bits
- 17.4.2 System Background Debug Force Reset Register (SBDFR)
- 17.4.3 DBG Registers and Control Bits
- 17.4.3.1 Debug Comparator A High Register (DBGCAH)
- 17.4.3.2 Debug Comparator A Low Register (DBGCAL)
- 17.4.3.3 Debug Comparator B High Register (DBGCBH)
- 17.4.3.4 Debug Comparator B Low Register (DBGCBL)
- 17.4.3.5 Debug FIFO High Register (DBGFH)
- 17.4.3.6 Debug FIFO Low Register (DBGFL)
- 17.4.3.7 Debug Control Register (DBGC)
- 17.4.3.8 Debug Trigger Register (DBGT)
- 17.4.3.9 Debug Status Register (DBGS)
- Appendix A Electrical Characteristics
- A.1 Introduction
- A.2 Parameter Classification
- A.3 Absolute Maximum Ratings
- A.4 Thermal Characteristics
- A.5 ESD Protection and Latch-Up Immunity
- A.6 DC Characteristics
- A.7 Supply Current Characteristics
- A.8 External Oscillator (XOSC) Characteristics
- A.9 Internal Clock Source (ICS) Characteristics
- A.10 Analog Comparator (ACMP) Electricals
- A.11 ADC Characteristics
- A.12 AC Characteristics
- A.13 FLASH Specifications
- A.14 EMC Performance
- Appendix B Ordering Information and Mechanical Drawings
Chapter 5 Resets, Interrupts, and General System Control
MC9S08SH8 MCU Series Data Sheet, Rev. 3
64 Freescale Semiconductor
When an interrupt condition occurs, an associated flag bit becomes set. If the associated local interrupt
enable is 1, an interrupt request is sent to the CPU. Within the CPU, if the global interrupt mask (I bit in
the CCR) is 0, the CPU will finish the current instruction; stack the PCL, PCH, X, A, and CCR CPU
registers; set the I bit; and then fetch the interrupt vector for the highest priority pending interrupt.
Processing then continues in the interrupt service routine.
Table 5-2. Vector Summary
Vector
Priority
Vector
Number
Address
(High/Low)
Vector
Name
Module Source Enable Description
Lowest
Highest
31 0xFFC0/0xFFC1 — — — — —
30 0xFFC2/0xFFC3 Vacmp ACMP ACF ACIE Analog comparator
29 0xFFC4/0xFFC5 — — — — —
28 0xFFC6/0xFFC7 — — — — —
27 0xFFC8/0xFFC9 — — — — —
26 0xFFCA/0xFFCB Vmtim MTIM TOF TOIE MTIM overflow
25 0xFFCC/0xFFCD Vrtc RTC RTIF RTIE Real-time interrupt
24 0xFFCE/0xFFCF Viic IIC IICIF IICIE IIC control
23 0xFFD0/0xFFD1 Vadc ADC COCO AIEN ADC
22 0xFFD2/0xFFD3 — — — — —
21 0xFFD4/0xFFD5 Vportb Port B PTBIF PTBIE Port B Pins
20 0xFFD6/0xFFD7 Vporta Port A PTAIF PTAIE Port A Pins
19 0xFFD8/0xFFD9 — — — — —
18 0xFFDA/0xFFDB Vscitx SCI TDRE, TC TIE, TCIE SCI transmit
17 0xFFDC/0xFFDD Vscirx SCI IDLE, RDRF,
LBKDIE,
RXEDGIF
ILIE, RIE, LDBKDIF,
RXEDGIE
SCI receive
16 0xFFDE/0xFFDF Vscierr SCI OR, NF,
FE, PF
ORIE, NFIE,
FEIE, PFIE
SCI error
15 0xFFE0/0xFFE1 Vspi SPI SPIF, MODF,
SPTEF
SPIE, SPIE, SPTIE SPI
14 0xFFE2/0xFFE3 Vtpm2ovf TPM2 TOF TOIE TPM2 overflow
13 0xFFE4/0xFFE5 Vtpm2ch1 TPM2 CH1F CH1IE TPM2 channel 1
12 0xFFE6/0xFFE7 Vtpm2ch0 TPM2 CH0F CH0IE TPM2 channel 0
11 0xFFE8/0xFFE9 Vtpm1ovf TPM1 TOF TOIE TPM1 overflow
10 0xFFEA/0xFFEB — — — — —
9 0xFFEC/0xFFED — — — — —
8 0xFFEE/0xFFEF — — — — —
7 0xFFF0/0xFFF1 — — — — —
6 0xFFF2/0xFFF3 Vtpm1ch1 TPM1 CH1F CH1IE TPM1 channel 1
5 0xFFF4/0xFFF5 Vtpm1ch0 TPM1 CH0F CH0IE TPM1 channel 0
4 0xFFF6/0xFFF7 — — — — —
3 0xFFF8/0xFFF9 Vlvd System
control
LVWF LVWIE Low-voltage warning
2 0xFFFA/0xFFFB Virq IRQ IRQF IRQIE IRQ pin
1 0xFFFC/0xFFFD Vswi Core SWI Instruction — Software interrupt
0 0xFFFE/0xFFFF Vreset System
control
COP,
LVD,
RESET pin,
Illegal opcode,
Illegal address
COPT
LVDRE
—
—
—
Watchdog timer
Low-voltage detect
External pin
Illegal opcode
Illegal address