Datasheet
Table Of Contents
- MC9S08SH8DS_Readme
- MC9S08SH8_DSAD_Rev.1
- MC9S08SH8
- Chapter 1 Device Overview
- Chapter 2 Pins and Connections
- Chapter 3 Modes of Operation
- Chapter 4 Memory
- Chapter 5 Resets, Interrupts, and General System Control
- 5.1 Introduction
- 5.2 Features
- 5.3 MCU Reset
- 5.4 Computer Operating Properly (COP) Watchdog
- 5.5 Interrupts
- 5.6 Low-Voltage Detect (LVD) System
- 5.7 Reset, Interrupt, and System Control Registers and Control Bits
- 5.7.1 Interrupt Pin Request Status and Control Register (IRQSC)
- 5.7.2 System Reset Status Register (SRS)
- 5.7.3 System Background Debug Force Reset Register (SBDFR)
- 5.7.4 System Options Register 1 (SOPT1)
- 5.7.5 System Options Register 2 (SOPT2)
- 5.7.6 System Device Identification Register (SDIDH, SDIDL)
- 5.7.7 System Power Management Status and Control 1 Register (SPMSC1)
- 5.7.8 System Power Management Status and Control 2 Register (SPMSC2)
- Chapter 6 Parallel Input/Output Control
- 6.1 Port Data and Data Direction
- 6.2 Pull-up, Slew Rate, and Drive Strength
- 6.3 Ganged Output
- 6.4 Pin Interrupts
- 6.5 Pin Behavior in Stop Modes
- 6.6 Parallel I/O and Pin Control Registers
- 6.6.1 Port A Registers
- 6.6.1.1 Port A Data Register (PTAD)
- 6.6.1.2 Port A Data Direction Register (PTADD)
- 6.6.1.3 Port A Pull Enable Register (PTAPE)
- 6.6.1.4 Port A Slew Rate Enable Register (PTASE)
- 6.6.1.5 Port A Drive Strength Selection Register (PTADS)
- 6.6.1.6 Port A Interrupt Status and Control Register (PTASC)
- 6.6.1.7 Port A Interrupt Pin Select Register (PTAPS)
- 6.6.1.8 Port A Interrupt Edge Select Register (PTAES)
- 6.6.2 Port B Registers
- 6.6.2.1 Port B Data Register (PTBD)
- 6.6.2.2 Port B Data Direction Register (PTBDD)
- 6.6.2.3 Port B Pull Enable Register (PTBPE)
- 6.6.2.4 Port B Slew Rate Enable Register (PTBSE)
- 6.6.2.5 Port B Drive Strength Selection Register (PTBDS)
- 6.6.2.6 Port B Interrupt Status and Control Register (PTBSC)
- 6.6.2.7 Port B Interrupt Pin Select Register (PTBPS)
- 6.6.2.8 Port B Interrupt Edge Select Register (PTBES)
- 6.6.3 Port C Registers
- 6.6.1 Port A Registers
- Chapter 7 Central Processor Unit (S08CPUV2)
- 7.1 Introduction
- 7.2 Programmer’s Model and CPU Registers
- 7.3 Addressing Modes
- 7.4 Special Operations
- 7.5 HCS08 Instruction Set Summary
- Chapter 8 Analog Comparator 5-V (S08ACMPV2)
- Chapter 9 Analog-to-Digital Converter (S08ADCV1)
- 9.1 Introduction
- 9.2 External Signal Description
- 9.3 Register Definition
- 9.3.1 Status and Control Register 1 (ADCSC1)
- 9.3.2 Status and Control Register 2 (ADCSC2)
- 9.3.3 Data Result High Register (ADCRH)
- 9.3.4 Data Result Low Register (ADCRL)
- 9.3.5 Compare Value High Register (ADCCVH)
- 9.3.6 Compare Value Low Register (ADCCVL)
- 9.3.7 Configuration Register (ADCCFG)
- 9.3.8 Pin Control 1 Register (APCTL1)
- 9.3.9 Pin Control 2 Register (APCTL2)
- 9.3.10 Pin Control 3 Register (APCTL3)
- 9.4 Functional Description
- 9.5 Initialization Information
- 9.6 Application Information
- Chapter 10 Internal Clock Source (S08ICSV2)
- 10.1 Introduction
- 10.2 External Signal Description
- 10.3 Register Definition
- 10.4 Functional Description
- Chapter 11 Inter-Integrated Circuit (S08IICV2)
- Chapter 12 Modulo Timer (S08MTIMV1)
- Chapter 13 Real-Time Counter (S08RTCV1)
- Chapter 14 Serial Communications Interface (S08SCIV4)
- Chapter 15 Serial Peripheral Interface (S08SPIV3)
- Chapter 16 Timer Pulse-Width Modulator (S08TPMV3)
- Chapter 17 Development Support
- 17.1 Introduction
- 17.2 Background Debug Controller (BDC)
- 17.3 On-Chip Debug System (DBG)
- 17.4 Register Definition
- 17.4.1 BDC Registers and Control Bits
- 17.4.2 System Background Debug Force Reset Register (SBDFR)
- 17.4.3 DBG Registers and Control Bits
- 17.4.3.1 Debug Comparator A High Register (DBGCAH)
- 17.4.3.2 Debug Comparator A Low Register (DBGCAL)
- 17.4.3.3 Debug Comparator B High Register (DBGCBH)
- 17.4.3.4 Debug Comparator B Low Register (DBGCBL)
- 17.4.3.5 Debug FIFO High Register (DBGFH)
- 17.4.3.6 Debug FIFO Low Register (DBGFL)
- 17.4.3.7 Debug Control Register (DBGC)
- 17.4.3.8 Debug Trigger Register (DBGT)
- 17.4.3.9 Debug Status Register (DBGS)
- Appendix A Electrical Characteristics
- A.1 Introduction
- A.2 Parameter Classification
- A.3 Absolute Maximum Ratings
- A.4 Thermal Characteristics
- A.5 ESD Protection and Latch-Up Immunity
- A.6 DC Characteristics
- A.7 Supply Current Characteristics
- A.8 External Oscillator (XOSC) Characteristics
- A.9 Internal Clock Source (ICS) Characteristics
- A.10 Analog Comparator (ACMP) Electricals
- A.11 ADC Characteristics
- A.12 AC Characteristics
- A.13 FLASH Specifications
- A.14 EMC Performance
- Appendix B Ordering Information and Mechanical Drawings
Chapter 5 Resets, Interrupts, and General System Control
MC9S08SH8 MCU Series Data Sheet, Rev. 3
66 Freescale Semiconductor
5.7.1 Interrupt Pin Request Status and Control Register (IRQSC)
This direct page register includes status and control bits, which are used to configure the IRQ function,
report status, and acknowledge IRQ events.
76543210
R0
IRQPDD IRQEDG IRQPE
IRQF 0
IRQIE IRQMOD
W IRQACK
Reset 00000000
= Unimplemented or Reserved
Figure 5-2. Interrupt Request Status and Control Register (IRQSC)
Table 5-3. IRQSC Register Field Descriptions
Field Description
6
IRQPDD
Interrupt Request (IRQ) Pull Device Disable — This read/write control bit is used to disable the internal pullup
device when the IRQ pin is enabled (IRQPE = 1) allowing for an external device to be used.
0 IRQ pull device enabled if IRQPE = 1.
1 IRQ pull device disabled if IRQPE = 1.
5
IRQEDG
Interrupt Request (IRQ) Edge Select — This read/write control bit is used to select the polarity of edges or
levels on the IRQ pin that cause IRQF to be set. The IRQMOD control bit determines whether the IRQ pin is
sensitive to both edges and levels or only edges. When the IRQ pin is enabled as the IRQ input and is configured
to detect rising edges. When IRQEDG = 1 and the internal pull device is enabled, the pull-up device is
reconfigured as an optional pull-down device.
0 IRQ is falling edge or falling edge/low-level sensitive.
1 IRQ is rising edge or rising edge/high-level sensitive.
4
IRQPE
IRQ Pin Enable — This read/write control bit enables the IRQ pin function. When this bit is set the IRQ pin can
be used as an interrupt request.
0 IRQ pin function is disabled.
1 IRQ pin function is enabled.
3
IRQF
IRQ Flag — This read-only status bit indicates when an interrupt request event has occurred.
0 No IRQ request.
1 IRQ event detected.
2
IRQACK
IRQ Acknowledge — This write-only bit is used to acknowledge interrupt request events (write 1 to clear IRQF).
Writing 0 has no meaning or effect. Reads always return 0. If edge-and-level detection is selected (IRQMOD = 1),
IRQF cannot be cleared while the IRQ pin remains at its asserted level.
1
IRQIE
IRQ Interrupt Enable — This read/write control bit determines whether IRQ events generate an interrupt
request.
0 Interrupt request when IRQF set is disabled (use polling).
1 Interrupt requested whenever IRQF = 1.
0
IRQMOD
IRQ Detection Mode — This read/write control bit selects either edge-only detection or edge-and-level
detection. The IRQEDG control bit determines the polarity of edges and levels that are detected as interrupt
request events. See Section 5.5.2.2, “Edge and Level Sensitivity,” for more details.
0 IRQ event on falling edges or rising edges only.
1 IRQ event on falling edges and low levels or on rising edges and high levels.