Datasheet
Table Of Contents
- MC9S08SH8DS_Readme
- MC9S08SH8_DSAD_Rev.1
- MC9S08SH8
- Chapter 1 Device Overview
- Chapter 2 Pins and Connections
- Chapter 3 Modes of Operation
- Chapter 4 Memory
- Chapter 5 Resets, Interrupts, and General System Control
- 5.1 Introduction
- 5.2 Features
- 5.3 MCU Reset
- 5.4 Computer Operating Properly (COP) Watchdog
- 5.5 Interrupts
- 5.6 Low-Voltage Detect (LVD) System
- 5.7 Reset, Interrupt, and System Control Registers and Control Bits
- 5.7.1 Interrupt Pin Request Status and Control Register (IRQSC)
- 5.7.2 System Reset Status Register (SRS)
- 5.7.3 System Background Debug Force Reset Register (SBDFR)
- 5.7.4 System Options Register 1 (SOPT1)
- 5.7.5 System Options Register 2 (SOPT2)
- 5.7.6 System Device Identification Register (SDIDH, SDIDL)
- 5.7.7 System Power Management Status and Control 1 Register (SPMSC1)
- 5.7.8 System Power Management Status and Control 2 Register (SPMSC2)
- Chapter 6 Parallel Input/Output Control
- 6.1 Port Data and Data Direction
- 6.2 Pull-up, Slew Rate, and Drive Strength
- 6.3 Ganged Output
- 6.4 Pin Interrupts
- 6.5 Pin Behavior in Stop Modes
- 6.6 Parallel I/O and Pin Control Registers
- 6.6.1 Port A Registers
- 6.6.1.1 Port A Data Register (PTAD)
- 6.6.1.2 Port A Data Direction Register (PTADD)
- 6.6.1.3 Port A Pull Enable Register (PTAPE)
- 6.6.1.4 Port A Slew Rate Enable Register (PTASE)
- 6.6.1.5 Port A Drive Strength Selection Register (PTADS)
- 6.6.1.6 Port A Interrupt Status and Control Register (PTASC)
- 6.6.1.7 Port A Interrupt Pin Select Register (PTAPS)
- 6.6.1.8 Port A Interrupt Edge Select Register (PTAES)
- 6.6.2 Port B Registers
- 6.6.2.1 Port B Data Register (PTBD)
- 6.6.2.2 Port B Data Direction Register (PTBDD)
- 6.6.2.3 Port B Pull Enable Register (PTBPE)
- 6.6.2.4 Port B Slew Rate Enable Register (PTBSE)
- 6.6.2.5 Port B Drive Strength Selection Register (PTBDS)
- 6.6.2.6 Port B Interrupt Status and Control Register (PTBSC)
- 6.6.2.7 Port B Interrupt Pin Select Register (PTBPS)
- 6.6.2.8 Port B Interrupt Edge Select Register (PTBES)
- 6.6.3 Port C Registers
- 6.6.1 Port A Registers
- Chapter 7 Central Processor Unit (S08CPUV2)
- 7.1 Introduction
- 7.2 Programmer’s Model and CPU Registers
- 7.3 Addressing Modes
- 7.4 Special Operations
- 7.5 HCS08 Instruction Set Summary
- Chapter 8 Analog Comparator 5-V (S08ACMPV2)
- Chapter 9 Analog-to-Digital Converter (S08ADCV1)
- 9.1 Introduction
- 9.2 External Signal Description
- 9.3 Register Definition
- 9.3.1 Status and Control Register 1 (ADCSC1)
- 9.3.2 Status and Control Register 2 (ADCSC2)
- 9.3.3 Data Result High Register (ADCRH)
- 9.3.4 Data Result Low Register (ADCRL)
- 9.3.5 Compare Value High Register (ADCCVH)
- 9.3.6 Compare Value Low Register (ADCCVL)
- 9.3.7 Configuration Register (ADCCFG)
- 9.3.8 Pin Control 1 Register (APCTL1)
- 9.3.9 Pin Control 2 Register (APCTL2)
- 9.3.10 Pin Control 3 Register (APCTL3)
- 9.4 Functional Description
- 9.5 Initialization Information
- 9.6 Application Information
- Chapter 10 Internal Clock Source (S08ICSV2)
- 10.1 Introduction
- 10.2 External Signal Description
- 10.3 Register Definition
- 10.4 Functional Description
- Chapter 11 Inter-Integrated Circuit (S08IICV2)
- Chapter 12 Modulo Timer (S08MTIMV1)
- Chapter 13 Real-Time Counter (S08RTCV1)
- Chapter 14 Serial Communications Interface (S08SCIV4)
- Chapter 15 Serial Peripheral Interface (S08SPIV3)
- Chapter 16 Timer Pulse-Width Modulator (S08TPMV3)
- Chapter 17 Development Support
- 17.1 Introduction
- 17.2 Background Debug Controller (BDC)
- 17.3 On-Chip Debug System (DBG)
- 17.4 Register Definition
- 17.4.1 BDC Registers and Control Bits
- 17.4.2 System Background Debug Force Reset Register (SBDFR)
- 17.4.3 DBG Registers and Control Bits
- 17.4.3.1 Debug Comparator A High Register (DBGCAH)
- 17.4.3.2 Debug Comparator A Low Register (DBGCAL)
- 17.4.3.3 Debug Comparator B High Register (DBGCBH)
- 17.4.3.4 Debug Comparator B Low Register (DBGCBL)
- 17.4.3.5 Debug FIFO High Register (DBGFH)
- 17.4.3.6 Debug FIFO Low Register (DBGFL)
- 17.4.3.7 Debug Control Register (DBGC)
- 17.4.3.8 Debug Trigger Register (DBGT)
- 17.4.3.9 Debug Status Register (DBGS)
- Appendix A Electrical Characteristics
- A.1 Introduction
- A.2 Parameter Classification
- A.3 Absolute Maximum Ratings
- A.4 Thermal Characteristics
- A.5 ESD Protection and Latch-Up Immunity
- A.6 DC Characteristics
- A.7 Supply Current Characteristics
- A.8 External Oscillator (XOSC) Characteristics
- A.9 Internal Clock Source (ICS) Characteristics
- A.10 Analog Comparator (ACMP) Electricals
- A.11 ADC Characteristics
- A.12 AC Characteristics
- A.13 FLASH Specifications
- A.14 EMC Performance
- Appendix B Ordering Information and Mechanical Drawings
Chapter 16 Timer/PWM Module (S08TPMV3)
MC9S08SH8 MCU Series Data Sheet, Rev. 3
252 Freescale Semiconductor
Table 16-6. TPMxCnSC Field Descriptions
Field Description
7
CHnF
Channel n flag. When channel n is an input-capture channel, this read/write bit is set when an active edge occurs
on the channel n pin. When channel n is an output compare or edge-aligned/center-aligned PWM channel, CHnF
is set when the value in the TPM counter registers matches the value in the TPM channel n value registers. When
channel n is an edge-aligned/center-aligned PWM channel and the duty cycle is set to 0% or 100%, CHnF will
not be set even when the value in the TPM counter registers matches the value in the TPM channel n value
registers.
A corresponding interrupt is requested when CHnF is set and interrupts are enabled (CHnIE = 1). Clear CHnF by
reading TPMxCnSC while CHnF is set and then writing a logic 0 to CHnF. If another interrupt request occurs
before the clearing sequence is complete, the sequence is reset so CHnF remains set after the clear sequence
completed for the earlier CHnF. This is done so a CHnF interrupt request cannot be lost due to clearing a previous
CHnF.
Reset clears the CHnF bit. Writing a logic 1 to CHnF has no effect.
0 No input capture or output compare event occurred on channel n
1 Input capture or output compare event on channel n
6
CHnIE
Channel n interrupt enable. This read/write bit enables interrupts from channel n. Reset clears CHnIE.
0 Channel n interrupt requests disabled (use for software polling)
1 Channel n interrupt requests enabled
5
MSnB
Mode select B for TPM channel n. When CPWMS=0, MSnB=1 configures TPM channel n for edge-aligned PWM
mode. Refer to the summary of channel mode and setup controls in Table 16-7.
4
MSnA
Mode select A for TPM channel n. When CPWMS=0 and MSnB=0, MSnA configures TPM channel n for
input-capture mode or output compare mode. Refer to Table 16-7 for a summary of channel mode and setup
controls.
Note: If the associated port pin is not stable for at least two bus clock cycles before changing to input capture
mode, it is possible to get an unexpected indication of an edge trigger.
3–2
ELSnB
ELSnA
Edge/level select bits. Depending upon the operating mode for the timer channel as set by CPWMS:MSnB:MSnA
and shown in Table 16-7, these bits select the polarity of the input edge that triggers an input capture event, select
the level that will be driven in response to an output compare match, or select the polarity of the PWM output.
Setting ELSnB:ELSnA to 0:0 configures the related timer pin as a general purpose I/O pin not related to any timer
functions. This function is typically used to temporarily disable an input capture channel or to make the timer pin
available as a general purpose I/O pin when the associated timer channel is set up as a software timer that does
not require the use of a pin.
Table 16-7. Mode, Edge, and Level Selection
CPWMS MSnB:MSnA ELSnB:ELSnA Mode Configuratio
X XX 00 Pin not used for TPM - revert to general
purpose I/O or other peripheral control