PCF85063A Tiny Real-Time Clock/calendar with alarm function and I2C-bus Rev. 4 — 24 November 2014 Product data sheet 1. General description The PCF85063A is a CMOS1 Real-Time Clock (RTC) and calendar optimized for low power consumption. An offset register allows fine-tuning of the clock. All addresses and data are transferred serially via the two-line bidirectional I2C-bus. Maximum data rate is 400 kbit/s. The register address is incremented automatically after each written or read data byte.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 4. Ordering information Table 1. Ordering information Type number Package Name Description Version PCF85063AT SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 PCF85063ATL DFN2626-10 plastic thermal enhanced extremely thin small outline package; no leads; 10 terminals; body 2.6 2.6 0.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 6. Block diagram 26&2 26&, &/.2( N+] 26&,//$725 ',9,'(5 32:(5 21 5(6(7 &/2&. &$/,%5$7,21 2))6(7 9'' &/2&. 287 &/.287 6<67(0 &21752/ ,17(55837 &21752/ ,17 966 6'$ 6&/ O & %86 ,17(5)$&( 5($/ 7,0( &/2&. $/$50 $1' 7,0(5 &21752/ 3&) $ DDD Fig 1. PCF85063A Product data sheet Block diagram of PCF85063A All information provided in this document is subject to legal disclaimers. Rev.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 7. Pinning information 7.1 Pinning 3&) $7 26&, 9'' 26&2 &/.287 ,17 6&/ 966 6'$ DDD For mechanical details, see Figure 32. Fig 2. Pin configuration for SO8 (PCF85063AT) 3&) $7/ 26&, 9'' 26&2 &/.287 &/.2( Q F ,17 6&/ 966 6'$ DDD 7UDQVSDUHQW WRS YLHZ For mechanical details, see Figure 33. Fig 3.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 7.2 Pin description Table 4. Pin description Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8. Functional description The PCF85063A contains 18 8-bit registers with an auto-incrementing register address, an on-chip 32.768 kHz oscillator with integrated capacitors, a frequency divider which provides the source clock for the Real-Time Clock (RTC) and calender, and an I2C-bus interface with a maximum data rate of 400 kbit/s.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors PCF85063A Product data sheet 8.1 Registers organization Table 5.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2 Control registers 8.2.1 Register Control_1 Table 6. Control_1 - control and status register 1 (address 00h) bit description Bit Symbol 7 EXT_TEST 6 - 5 STOP 4 Value - 2 CIE 1 external clock test mode Section 8.2.1.1 normal mode 1 external clock test mode 0 unused - STOP bit Section 8.2.1.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.1.1 EXT_TEST: external clock test mode A test mode is available which allows for on-board testing. In this mode, it is possible to set up test conditions and control the operation of the RTC. The test mode is entered by setting bit EXT_TEST in register Control_1. Then pin CLKOUT becomes an input. The test mode replaces the internal clock signal with the signal applied to pin CLKOUT.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.1.2 STOP: STOP bit function The function of the STOP bit (see Figure 6) is to allow for accurate starting of the time circuits. The STOP bit function causes the upper part of the prescaler (F2 to F14) to be held in reset and thus no 1 Hz ticks are generated. It also stops the output of clock frequencies below 8 kHz on pin CLKOUT.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Table 7. First increment of time circuits after STOP bit release Bit Prescaler bits STOP F0F1-F2 to F14 [1] 1 Hz tick Time Comment hh:mm:ss Clock is running normally 0 12:45:12 01-0 0001 1101 0100 prescaler counting normally STOP bit is activated by user.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.1.3 Software reset A reset is automatically generated at power-on. A reset can also be initiated with the software reset command. Software reset command means setting bits 6, 4, and 3 in register Control_1 (00h) logic 1 and all other bits logic 0 by sending the bit sequence 01011000 (58h), see Figure 8.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus The PCF85063A resets to: Time — 00:00:00 Date — 20000101 Weekday — Saturday 8.2.2 Register Control_2 Table 9. Control_2 - control and status register 2 (address 01h) bit description Bit Symbol 7 AIE 6 Value Description Reference alarm interrupt Section 8.2.2.1 Section 8.5.6 0[1] disabled 1 enabled AF alarm flag 0[1] read: alarm flag inactive Section 8.2.2.1 Section 8.5.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.2.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus VHFRQGV FRXQWHU PLQXWHV FRXQWHU ,17 ZKHQ 0, HQDEOHG 7) ZKHQ 0, HQDEOHG DDD In this example, the TF flag is not cleared after an interrupt. Fig 10. INT example for MI Table 10.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.2.4 COF[2:0]: Clock output frequency A programmable square wave is available at pin CLKOUT. Operation is controlled by the COF[2:0] bits in the register Control_2. Frequencies of 32.768 kHz (default) down to 1 Hz can be generated for use as a system clock, microcontroller clock, input to a charge pump, or for calibration of the oscillator. Pin CLKOUT is a push-pull output and enabled at power-on.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.3 Register Offset The PCF85063A incorporates an offset register (address 02h) which can be used to implement several functions, such as: • Accuracy tuning • Aging adjustment • Temperature compensation Table 12.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.3.1 Correction when MODE = 0 The correction is triggered once every two hours and then correction pulses are applied once per minute until the programmed correction values have been implemented. Table 14.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.3.2 Correction when MODE = 1 The correction is triggered once every four minutes and then correction pulses are applied once per second up to a maximum of 60 pulses. When correction values greater than 60 pulses are used, additional correction pulses are made in the 59th second. Clock correction is made more frequently in MODE = 1; however, this can result in higher power consumption. Table 16.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.3.3 Offset calibration workflow The calibration offset has to be calculated based on the time. Figure 11 shows the workflow how the offset register values can be calculated: 0HDVXUH WKH IUHTXHQF\ RQ SLQ &/.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus GHYLDWLRQ DIWHU FRUUHFWLRQ LQ 02'( SSP GHYLDWLRQ DIWHU FRUUHFWLRQ LQ 02'( SSP PHDVXUHG FDOFXODWHG GHYLDWLRQ SSP DDD With the offset calibration an accuracy of 2 ppm (0.5 offset per LSB) can be reached (see Table 13). 1 ppm corresponds to a time deviation of 0.0864 seconds per day.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Table 20. Seconds coded in BCD format Seconds value in decimal Digit (unit place) Bit 6 Bit 3 Bit 5 Bit 4 Bit 2 Bit 1 Bit 0 00[1] 0 0 0 0 0 0 0 01 0 0 0 0 0 0 1 02 0 0 0 0 0 1 0 : : : : : : : : 09 0 0 0 1 0 0 1 10 0 0 1 0 0 0 0 : : : : : : : : 58 1 0 1 1 0 0 0 59 1 0 1 1 0 0 1 [1] 8.3.1.1 Upper-digit (ten’s place) Default value.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.3.2 Register Minutes Table 21. Minutes - minutes register (address 05h) bit description Bit Symbol Value Place value Description 7 - 0 - unused MINUTES 0[1] ten’s place actual minutes coded in BCD format 6 to 4 [1] to 5 0[1] to 9 3 to 0 unit place Default value. 8.3.3 Register Hours Table 22.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Table 25. Weekday assignments Day[1] Bit 2 1 0 Sunday 0 0 0 Monday 0 0 1 Tuesday 0 1 0 Wednesday 0 1 1 Thursday 1 0 0 Friday 1 0 1 Saturday[2] 1 1 0 [1] Definition may be reassigned by the user. [2] Default value. 8.3.6 Register Months Table 26.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.3.7 Register Years Table 28. Bit 7 to 4 Years - years register (0Ah) bit description Symbol Value Place value Description YEARS 0[1] to 9 ten’s place 0[1] to 9 unit place 3 to 0 [1] actual year coded in BCD format Default value. 8.4 Setting and reading the time Figure 14 shows the data flow and data dependencies starting from the 1 Hz clock tick.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus W V 67$57 6/$9( $''5(66 '$7$ '$7$ 6723 DDD Fig 15. Access time for read/write operations Because of this method, it is very important to make a read or write access in one go, that is, setting or reading seconds through to years should be made in one single access. Failing to comply with this method could result in the time becoming corrupted.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.5.2 Register Minute_alarm Table 30. Minute_alarm - minute alarm register (address 0Ch) bit description Bit Symbol 7 AEN_M 6 to 4 Value minute alarm MINUTE_ALARM 3 to 0 [1] Place value Description 0 - enabled 1[1] - disabled 0[1] to 5 ten’s place 0[1] to 9 unit place minute alarm information coded in BCD format Default value. 8.5.3 Register Hour_alarm Table 31.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.5.5 Register Weekday_alarm Table 33. Weekday_alarm - weekday alarm register (address 0Fh) bit description Bit Symbol 7 AEN_W 6 to 3 2 to 0 [1] Value Description weekday alarm 0 enabled 1[1] disabled - 0 WEEKDAY_ALARM 0[1] unused to 6 weekday alarm information coded in BCD format Default value. 8.5.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus H[DPSOH FKHFN QRZ VLJQDO $(1B6 $(1B6 6(&21' $/$50 6(&21' 7,0( $(1B0 0,187( $/$50 0,187( 7,0( $(1B+ +285 $/$50 VHW DODUP IODJ $) +285 7,0( $(1B' '$< $/$50 '$< 7,0( $(1B: :((.'$< $/$50 :((.'$< 7,0( DDD (1) Only when all enabled alarm settings are matching. It is only on increment to a matched case that the alarm flag is set. Fig 16. Alarm function block diagram 8.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.6.2 Register Timer_mode Table 35. Timer_mode - timer control register (address 11h) bit description Bit Symbol Value Description 7 to 5 - 000 unused 4 to 3 TCF[1:0] 2 timer clock frequency 00 4.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus When the counter decrements from 1, the timer flag (bit TF in register Control_2) is set and the counter automatically re-loads and starts the next timer period.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus At the end of every countdown, the timer sets the countdown timer flag (bit TF in register Control_2). Bit TF can only be cleared by command. The asserted bit TF can be used to generate an interrupt at pin INT. The interrupt may be generated as a pulsed signal every countdown period or as a permanently active signal which follows the condition of bit TF.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 9. Characteristics of the I2C-bus interface The I2C-bus is for bidirectional, two-line communication between different ICs or modules. The two lines are a Serial DAta line (SDA) and a Serial CLock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor. Data transfer may be initiated only when the bus is not busy. 9.1 Bit transfer One data bit is transferred during each clock pulse.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 0$67(5 75$160,77(5 5(&(,9(5 6/$9( 75$160,77(5 5(&(,9(5 6/$9( 5(&(,9(5 0$67(5 75$160,77(5 5(&(,9(5 0$67(5 75$160,77(5 6'$ 6&/ PJD Fig 20. System configuration 9.4 Acknowledge The number of data bytes transferred between the START and STOP conditions from transmitter to receiver is unlimited. Each byte of 8 bits is followed by an acknowledge cycle.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 9.5 I2C-bus protocol 9.5.1 Addressing One I2C-bus slave address (1010001) is reserved for the PCF85063A. The entire I2C-bus slave address byte is shown in Table 39. Table 39. I2C slave address byte Slave address Bit 7 6 5 4 3 2 1 MSB 0 LSB 1 0 1 0 0 0 1 R/W After a START condition, the I2C slave address has to be sent to the PCF85063A device.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus DFNQRZOHGJH IURP 3&) $ 6 VODYH DGGUHVV DFNQRZOHGJH IURP 3&) $ $ ZULWH ELW $ UHJLVWHU DGGUHVV K WR K DFNQRZOHGJH IURP 3&) $ 6 VODYH DGGUHVV UHDG ELW $ '$7$ %<7( VHW UHJLVWHU DGGUHVV 3 6723 DFNQRZOHGJH IURP PDVWHU QR DFNQRZOHGJH $ $ /$67 '$7$ %<7( 3 UHDG UHJLVWHU GDWD WR Q GDWD E\WHV DXWR LQFUHPHQW PHPRU\ UHJLVWHU DGGUHVV DXWR LQFUH
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 10. Internal circuitry 3&) $ 9'' 26&, &/.287 26&2 &/.2( 6&/ ,17 6'$ 966 DDD Fig 24. Device diode protection diagram of PCF85063A 11. Safety notes CAUTION This device is sensitive to ElectroStatic Discharge (ESD). Observe precautions for handling electrostatic sensitive devices. Such precautions are described in the ANSI/ESD S20.20, IEC/ST 61340-5, JESD625-A or equivalent standards.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 12. Limiting values Table 40. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VDD supply voltage IDD supply current VI input voltage VO output voltage II input current at any input IO output current at any output Ptot total power dissipation VESD Conditions Min Max Unit 0.5 +6.5 V 50 +50 mA 0.5 +6.5 V 0.5 +6.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 13. Characteristics Table 41. Static characteristics VDD = 0.9 V to 5.5 V; VSS = 0 V; Tamb = 40 C to +85 C; fosc = 32.768 kHz; quartz Rs = 60 k; CL = 7 pF; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit supply voltage interface inactive; fSCL = 0 Hz [1] 0.9 - 5.5 V interface active; fSCL = 400 kHz [1] 1.8 - 5.5 V CLKOUT disabled; VDD = 3.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Table 41. Static characteristics …continued VDD = 0.9 V to 5.5 V; VSS = 0 V; Tamb = 40 C to +85 C; fosc = 32.768 kHz; quartz Rs = 60 k; CL = 7 pF; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit fosc/fosc relative oscillator frequency variation VDD = 200 mV; Tamb = 25 C - 0.075 - ppm CL(itg) integrated load capacitance on pins OSCO, OSCI CL = 7 pF 4.2 7 9.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus DDD ,'' Q$ 7HPSHUDWXUH & CL(itg) = 7 pF; CLKOUT disabled. (1) VDD = 5.5 V. (2) VDD = 3.3 V. DDD ,'' Q$ 7HPSHUDWXUH & CL(itg) = 12.5 pF; CLKOUT disabled. (1) VDD = 5.5 V. (2) VDD = 3.3 V. Fig 26.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus DDD ,'' $ 9'' 9 Tamb = 25 C; fCLKOUT = 32768 Hz. (1) 47 pF CLKOUT load. (2) 22 pF CLKOUT load. DDD ,'' Q$ 9'' 9 Tamb = 25 C; CLKOUT disabled. (1) CL(itg) = 12.5 pF. (2) CL(itg) = 7 pF. Fig 27.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus DDD ,'' Q$ 56 N VDD = 3.3 V; CLKOUT disabled. (1) CL(itg) = 12.5 pF; 50 C; maximum value. (2) CL(itg) = 7 pF; 50 C; maximum value. (3) CL(itg) = 12.5 pF; 25 C; typical value. (4) CL(itg) = 7 pF; 25 C; typical value. Fig 28.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Table 42. I2C-bus characteristics VDD = 1.8 V to 5.5 V; VSS = 0 V; Tamb = 40 C to +85 C; fosc = 32.768 kHz; quartz Rs = 60 k; CL = 7 pF; unless otherwise specified. All timing values are valid within the operating supply voltage and temperature range and referenced to VIL and VIH with an input voltage swing of VSS to VDD[1].
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus SURWRFRO 67$57 FRQGLWLRQ 6 W68 67$ ELW 06% $ W/2: ELW $ W+,*+ I ELW 5 : DFNQRZOHGJH $ 6723 FRQGLWLRQ 3 6&/ 6&/ W%8) WU WI 6'$ W+' 67$ W68 '$7 W+' '$7 W9' '$7 W9' $&. W68 672 DDD Fig 30. I2C-bus timing diagram; rise and fall times refer to 30 % and 70 % PCF85063A Product data sheet All information provided in this document is subject to legal disclaimers. Rev.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 14. Application information 9'' 6'$ 5 0$67(5 75$160,77(5 5(&(,9(5 6&/ ) Q) 9'' &/.2( &/.287 ,17 6&/ 26&, 26&2 9'' 3&) $ 6'$ 5 966 5 5 SXOO XS UHVLVWRU 5 6'$ 6&/ , & EXV WU &E DDD A 1 farad super capacitor combined with a low VF diode can be used as a standby or back-up supply.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 15.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus ')1 SODVWLF WKHUPDO HQKDQFHG H[WUHPHO\ WKLQ VPDOO RXWOLQH SDFNDJH QR OHDGV WHUPLQDOV ERG\ [ [ PP 627 ; % ' $ $ ( $ $ WHUPLQDO LQGH[ DUHD GHWDLO ; H WHUPLQDO LQGH[ DUHD H & & $ % & Y Z E \ & \ / N (K 'K 'LPHQVLRQV 8QLW PP PD[ QRP PLQ PP VFDOH $ $ $ E ' 'K ( (K H H
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 76623 SODVWLF WKLQ VKULQN VPDOO RXWOLQH SDFNDJH OHDGV ERG\ ZLGWK PP ' ( 627 $ ; F \ +( Y 0 $ = $ SLQ LQGH[ $ $ $ ș /S / GHWDLO ; H Z 0 ES PP VFDOH ',0(16,216 PP DUH WKH RULJLQDO GLPHQVLRQV 81,7 $ PD[ $ $ $ ES F ' ( H +( / /S Y Z \ = ș PP
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 16. Handling information All input and output pins are protected against ElectroStatic Discharge (ESD) under normal handling. When handling Metal-Oxide Semiconductor (MOS) devices ensure that all normal precautions are taken as described in JESD625-A, IEC 61340-5 or equivalent standards. 17. Packing information 17.1 Tape and reel information For tape and reel packing information, please see for PCF85063AT — Ref.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 18. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 18.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 18.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 35. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 19.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus )RRWSULQW LQIRUPDWLRQ IRU UHIORZ VROGHULQJ RI ')1 SDFNDJH 627 +[ *[ ' 3 $\ *\ %\ 63\ 6/\ Q63\ +\ Q63[ 63[ 6/[ *HQHULF IRRWSULQW SDWWHUQ 5HIHU WR WKH SDFNDJH RXWOLQH GUDZLQJ IRU DFWXDO OD\RXW VROGHU ODQG VROGHU SDVWH GHSRVLW VROGHU ODQG SOXV VROGHU SDVWH RFFXSLHG DUHD VROGHU UHVLVW ',0(16,216 LQ PP 3 $\ ,VVXH GDWH %\ ' 6/[ 6/\ 63[ 63\ *[ *\ +[ +\
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus VROGHU ODQGV RFFXSLHG DUHD 'LPHQVLRQV LQ PP VRW BIU Fig 38. Footprint information for reflow soldering of SOT505-1 (TSSOP8) of PCF85063ATT PCF85063A Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 24 November 2014 © NXP Semiconductors N.V. 2014.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors PCF85063A Product data sheet 20. Appendix 20.1 Real-Time Clock selection Table 45.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Selection of Real-Time Clocks …continued Alarm, Timer, Interrupt Interface IDD, Battery Timestamp, Watchdog
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 21. Abbreviations Table 46.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 22.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 23. Revision history Table 47. Revision history Document ID Release date Data sheet status Change notice Supersedes PCF85063A v.4 20141124 Product data sheet - PCF85063A v.3 Modifications: • • • Added new product type PCF85063ATT Corrected rise and fall time specification according to the I2C standard, see Table 42 Adjusted Section 8.2.3 PCF85063A v.3 20140604 Product data sheet - PCF85063A v.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 24. Legal information 24.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use.
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 26. Tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Table 35. Table 36. Ordering information . . . . . . . . . . . . . . . . .
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 27. Figures Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Fig 10. Fig 11. Fig 12. Fig 13. Fig 14. Fig 15. Fig 16. Fig 17. Fig 18. Fig 19. Fig 20. Fig 21. Fig 22. Fig 23. Fig 24. Fig 25. Fig 26. Fig 27. Fig 28. Fig 29. Fig 30. Fig 31. Fig 32. Fig 33. Fig 34. Fig 35. Fig 36. Fig 37. Fig 38. Block diagram of PCF85063A . . . . . . . . . . . . . . . .3 Pin configuration for SO8 (PCF85063AT) . . . . . .
PCF85063A NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 28. Contents 1 2 3 4 4.1 5 6 7 7.1 7.2 8 8.1 8.2 8.2.1 8.2.1.1 8.2.1.2 8.2.1.3 8.2.2 8.2.2.1 8.2.2.2 8.2.2.3 8.2.2.4 8.2.3 8.2.3.1 8.2.3.2 8.2.3.3 8.2.4 8.3 8.3.1 8.3.1.1 8.3.2 8.3.3 8.3.4 8.3.5 8.3.6 8.3.7 8.4 8.5 8.5.1 8.5.2 8.5.3 8.5.4 8.5.5 8.5.6 8.6 8.6.1 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . .