Datasheet

MPC5674F Microcontroller Data Sheet, Rev. 9
Revision History
Freescale Semiconductor132
9
(Oct-2012)
Updated Table 1 (Orderable Part Numbers) with actual available parts.Added new part number
SPC5673FF3MVY2 ,Package description 516 PBGA, w/EBI, Pb-free.Speed is 200Mhz nom and max.
—Removed note attached to “Orderable Part Numbers” and “Freescale Part Number”.
Updated footnotes of Table 3 (Absolute Maximum Ratings) to:
• 2.0 V for 10 hours cumulative time, 1.2V +10% for time remaining.
• 6.4 V for 10 hours cumulative time, 5.0V +10% for time remaining.
• 5.3 V for 10 hours cumulative time, 3.3V +10% for time remaining.
Updated Table 6 (Thermal Characteristics, 324-pin Package) to show MPC5674F thermal characteristics.
In Table 10 (PMC Operating conditions) updated the parameter “Supply voltage VDD 1.2V nominal" to “Core
supply voltage".
In Table 11 (PMC Electrical Specifications) updated the following rows:
—Parameter “Nominal VRC regulated 1.2V output VDD” updated column “Typ” to 1.27 V.
—The minimum and maximum value of “Untrimmed VRC 1.2V output variation before band gap trim (unloaded)”
updated to “-14%” and “+10%” respectively.
—The minimum and maximum value of “Trimmed VRC 1.2V output variation after band gap trim (REGCTL load
max. 20mA, VDD load max 1A)” updated to “-10%” and “+5%” respectively.
In Table 12 (Power Sequence Pin States for MH and AE pads) updated the row(VDD33 = low, VDDE = high),
parameter “MH+LVDS Pads” to “Outputs disabled”.
In Table 13 (Power Sequence Pin States for F and FS pads) updated the rows
(VDD = low, VDD33 = low, VDDE = high)
and
(VDD = high, VDD33 = low, VDDE = high) ,parameter “F and FS pad” to “Outputs disabled”.
In Table 14 (DC Electrical Specifications) updated the spec 24 “Operating Current 1.2 V Supplies @ f
SYS
= 264
MHz” with 'V
DD
@ 1.32 V' Max value to 850 mA from 1.0 A, and deleted corresponding footnote stating that the
previous information was preliminary.
Updated current(mA) values in Table 15 (V
DDE
/V
DDEH
I/O Pad Average DC Current) from Spec 5 to 13.
-Spec 5 Current (mA) from 6.5 to 7.4
-Spec 6 Current (mA) from 9.4 to 10.5
-Spec 7 Current (mA) from 10.8 to 12.3
-Spec 8 Current (mA) from 33.3 to 35.2
-Spec 9 Current (mA) from 12.0 to 12.7
-Spec 10 Current (mA) from 6.2 to 6.7
-Spec 11 Current (mA) from 4.0 to 4.2
-Spec 12 Current (mA) from 2.4 to 2.6
-Spec 13 Current (mA) from8.9 to 9.1
In Table 34 (Nexus Debug Port Timing) updated the footnote of parameter “t
CYC
” to “See Notes on tcyc in
Table 27 “.Removed references to “Section I/O Pad VDD33 Current Specifications” .
Table 46. Revision History (continued)
Revision
(Date)
Description of changes