Datasheet

MPC5674F Microcontroller Data Sheet, Rev. 9
Electrical Characteristics
Freescale Semiconductor32
27 Operating Current V
DDE
/V
DDEH
17
Supplies
V
DDE2
V
DDEH1
V
DDEH3
V
DDEH4
V
DDEH5
V
DDEH6
V
DDEH7
I
DD2
I
DD1
I
DD3
I
DD4
I
DD5
I
DD6
I
DD7
—
—
—
—
—
—
—
note
17
mA
mA
mA
mA
mA
mA
mA
28 Fast I/O Weak Pull Up/Down Current
18
3.0 V–3.6 V I
ACT_F
42 158 A
29 Medium I/O Weak Pull Up/Down Current
19
3.0 V–3.6 V
4.5 V–5.5 V
I
ACT_S
15
35
95
200
A
A
30 I/O Input Leakage Current
20
I
INACT_D
–2.5 2.5 A
31 DC Injection Current (per pin) I
IC
–1.0 1.0 mA
32 Analog Input Current, Channel Off
21
, AN[0:7], AN38,
AN39
Analog Input Current, Channel Off, all other analog
inputs AN[x]
I
INACT_A
–250
–150
250
150
nA
nA
33 V
SS
Differential Voltage V
SS
–V
SSA
–100 100 mV
34 Analog Reference Low Voltage V
RL
V
SSA
V
SSA
+100 mV
35 V
RL
Differential Voltage V
RL
–V
SSA
–100 100 mV
36 Analog Reference High Voltage V
RH
V
DDA
–100 V
DDA
mV
37 V
REF
Differential Voltage V
RH
–V
RL
4.75 5.25 V
38 V
SSSYN
to V
SS
Differential Voltage V
SSSYN
–V
SS
–100 100 mV
39
Operating Temperature Range—Ambient (Packaged) T
A
(T
L
to T
H
) –40.0 125.0

C
40 Slew rate on power supply pins — — 25 V/ms
41 Weak Pull-Up/Down Resistance
22
, 200 K Option R
PUPD200K
130 280 k
42 Weak Pull-Up/Down Resistance
22
, 100 K Option R
PUPD100K
65 140 k
43 Weak Pull-Up/Down Resistance
22
, 5 K Option R
PUPD5K
1.4 7.5 k
44 Pull-Up/Down Resistance Matching Ratios
23
(100K/200K)
R
PUPDMTCH
–2.5 +2.5 %
1
Voltage overshoots during a high-to-low or low-to-high transition must not exceed 10 seconds per instance.
2
2.0 V for 10 hours cumulative time, 1.2 V +10% for time remaining.
3
Assumed with DC load.
4
5.3 V for 10 hours cumulative time, 3.3 V +10% for time remaining.
5
6.4 V for 10 hours cumulative time, 5.0 V +10% for time remaining.
6
V
STBY
below 0.95 V the RAM will not retain states, but will be operational. V
STBY
can be 0 V when bypass standby mode.
7
Regulator is functional with derated performance, with supply voltage down to 4.0 V for system with V
DDREG
=4.5V (min).
8
2.7 V minimum operating voltage allowed during vehicle crank for system with V
DDREG
= 3.0 V (min). Normal operating voltage
should be either V
DDREG
= 3.0 V (min) or 4.5 V (min) depending on the user regulation voltage system selected.
9
Required to be supplied when 3.3 V regulator is disabled. See Section 4.5, “PMC/POR/LVI Electrical Specifications.”
Table 14. DC Electrical Specifications (continued)
Spec Characteristic Symbol Min Max Unit