NPCS549 INSTRUCTION MANUAL ARIES™ PRIME WIRELESS HD TRANSMITTER
TABLE OF CONTENTS What’s Included............................................................................................................................2 Features........................................................................................................................................2 Buttons and Connections..............................................................................................................3 Setup...................................................................
BUTTONS AND CONNECTIONS Transmitter - FRONT 1 2 Transmitter - SIDE 3 4 1 Pairing button 2 LED Status Indicator 3 USB Power Input 4 HDMI input To PAIR transmitter & receiver Is a SOLID WHITE colour when the power is ON and has a successful wireless connection Connect the transmitter to the desktop or laptop’s USB port with the provided USB cable Plug in the Transmitter directly to a PC, cable box or any HDMI device -3-
BUTTONS AND CONNECTIONS Receiver - TOP Receiver - BOTTOM 1 2 3 4 Receiver - SIDE HDMI 5 1 Power Button with LED indicator 2 INFO Button 3 4 5 6 Status LED Mounting Holes DC Input HDMI Output 6 Press to turn the receiver ON and OFF. The indicator in the power button lights up in WHITE when the power is ON, and turns ORANGE in STANDBY MODE. Press this button to display OSD information on the HDTV screen. Displays the VIDEO STATUS information. Allows you to hang the Receiver on the wall.
SETUP CONNECTING THE TRANSMITTER 1. Connect the Transmitter directly to a PC, cable box or any HDMI device. 2. Connect the Transmitter directly to a PC, cable box or any HDMI device using the USB cable provided or connect the power adapter to the mini USB port of the transmitter and plug it to an available wall outlet. 3. You may also connect the Right Angle HDMI® Adapter for easier setup with certain computers.
SETUP WALL MOUNTING 1. Drill pilot holes using drilling template included below. 2. Insert the supplied two anchors into the wall. 3. Insert two screws into the anchors. Leave 1/8” length for mounting the Transmitter or Receiver. 4. Remove the rubber feet from the NPCS549. Place NPCS549 main holes over the protruding screws and slide down into position. DRILLING TEMPLATE CONNECTING THE RECEIVER TO HDTV 1.
SETUP 3. Once the Transmitter and Receiver are both connected, they will automatically pair to each other. 4. When you disconnect the transmitter and the link is disconnected over 10 minutes, the Receiver will enter STANDBY MODE (Power LED of receiver is ORANGE).
SETUP 5. Connect the power adapter to the DC Input of the Receiver and into a wall outlet. When the unit is successfully connected, the Power LED indicator on the POWER button lights up in WHITE. 6. Once the Transmitter and Receiver are both connected, they will automatically pair to each other. 7. During the warm-up period, the POWER LED will flash WHITE until the signal between the Transmitter and the Receiver is established.
SETUP 9. If all is operating normally, the POWER LED and INFO/CHANNEL LED will be SOLID WHITE.
SETUP BUTTON POWER INFO RECEIVER OSD Press the POWER button on TOP of the receiver to go from " Active mode" to " Active Standby mode". Press the INFO button on TOP of the receiver. The Signal Quality, Source, Channel and Resolution will be displayed on the OSD for your reference. Press the INFO button again to exit. OSD DISPLAY HDMI CH10 1280x1024 = OFF AUDIO BIT RATE SUPPORT • Digital Audio from HDMI inputs: Up to 6Mbit/s bit-rate support. • Support AC3 and DTS.
SETUP Windows Vista OS: 1. Go to START MENU 1 in bottom left corner of the screen. Click WINDOWS MOBILITY CENTER 2 to open. 2. On the EXTERNAL DISPLAY title, click CONNECT DISPLAY 3 to open NEW DISPLAY DETECTED 4 . 3. Choose MIRRORED or EXTENDED mode to enable external display. Windows XP OS: 1. Right click the mouse on your desktop. 2. Click GRAPHIC OPTION / OUTPUT TO. 3. Click CLONE MODE or EXTENDED DISPLAY NOTE: For more information, please type CHANGE DISPLAY SETTINGS in WINDOWS HELP AND SUPPORT.
SETUP Windows OS Audio setting to switch to HDMI output: Windows7 OS: 1. Go to START MENU in bottom left corner of the screen. Click CONTROL PANEL to open AUDIO setting. 2. Select HDMI OUTPUT 1 and Press OK 2 . WindowsXP OS: 1. Go to START MENU in bottom left corner of the screen. Click CONTROL PANEL to open AUDIO setting. 2. Select HDMI OUTPUT and Press OK. NOTE: For more information, please type CHANGE AUDIO SETTINGS in WINDOWS HELP AND SUPPORT.
SETUP Windows Vista OS: 1. Go to START MENU 1 in bottom left corner of the screen. Click WINDOWS MOBILITY CENTER 2 to open. 2. On the VOLUME 3 tab, click the CHANGE AUDIO SETTING 4 icon to open the SOUND section. 3. Select HDMI OUTPUT 5 and press OK 6 .
SETUP SUPPORTED RESOLUTIONS If the SOURCE LED continues to flash WHITE (slower than "NO SIGNAL" mode); the OSD display shows: , and there is no video displayed or the video quality is poor, it indicates that the video frame rate from your A/V source device is not supported. Ensure that the timing of your HD device is compliant with the standards listed below: VIDEO FORMAT TIMING RESOLUTION PRIMARY CEA VIDEO TIMING 640X480P @ 59.94 / 60HZ SUPPORTED YES 720X480P @ 59.
TROUBLESHOOTING Before following the troubleshooting guide below please make sure that your Transmitter, Receiver and ANY attached equipment are all properly connected, switched on and not in "Standby Mode". POWER • Make sure the power is connected to the Receiver/Transmitter. LED is not • Check that the power supplies are connected to a working power outlet. lighting up • The POWER LED of the Receiver/Transmitter should be WHITE.
SPECIFICATIONS System Requirements Supported Audio Formats Supported Video Resolutions Digital Audio Any laptop or desktop system containing an HDMI port including popular models from these manufacturers: Alienware, Lenovo, Dell, HP, Acer, Apple (Display Port cable not included) up to 6 Mbps AC3 and DTS HDMI Input 1080p, 1080i, 720p, 576p, 480p Transmission Distance System Latency Transmission Frequency Antenna Power Supply Operating temperature INTERFACES HDMI Input AV INTERFACES HDMI Output POWER POWE
FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
IC STATEMENT This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
SAFETY INFORMATION 1. 2. 3. 4. 5. 6. 7. Read all instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
SAFETY INFORMATION Do not use close to refrigerators, washing machines and metal furniture. Place on a stable surface and make sure connecting wires are routed to minimize the chance of accidents. Only use the DC power adaptors supplied, if they must be replaced make sure the replacements have the same output rating of 5V 3A DC.
NOTES - 21 -
NYRIUS® WARRANTY Thank you for choosing NYRIUS® Consumer Electronics Products! NYRIUS gives the following express warranty to the original consumer purchaser or gift recipient for this NYRIUS product, when shipped in its original container and sold or distributed by NYRIUS or by an Authorized NYRIUS Dealer: NYRIUS warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship.
