Pocke User Manual
Please Read Before Proceeding THE BATTERY IS NOT CHARGED WHEN YOU TAKE IT OUT OF THE BOX. DO NOT REMOVE THE BATTERY PACK WHEN THE DEVICE IS CHARGING. YOUR WARRANTY IS INVALIDATED IF YOU OPEN OR TAMPER WITH THE DEVICE’S OUTER CASING. PRIVACY RESTRICTIONS Some countries require full disclosure of recorded telephone conversations, and stipulate that you must inform the person with whom you are speaking that the conversation is being recorded.
Macromedia, Flash, Macromedia Flash, Macromedia Flash Lite and Reader are trademarks and/or registered trademarks of Macromedia Netherlands, B.V. or Adobe Systems Incorporated. Copyright © 2006, JATAAYU SOFTWARE (P) LTD. All Rights Reserved. Copyright © 2006, Dilithium Networks, Inc. All Rights Reserved. Copyright © 2006, Tao Group Limited. All Rights Reserved. ArcSoft MMS Composer™ Copyright © 2003-2006, ArcSoft, Inc. and its licensors. All Rights Reserved.
Important Health Information and Safety Precautions When using this product, the safety precautions below must be taken to avoid possible legal liabilities and damages. Retain and follow all product safety and operating instructions. Observe all warnings in the operating instructions on the product. To reduce the risk of bodily injury, electric shock, fire, and damage to the equipment, observe the following precautions.
• AC Adapter 1. Delta, Model ADP-5FH X 2. Phihong, Models PSAA05X-050 Handle battery packs carefully This product contains a Li-ion Polymer battery. There is a risk of fire and burns if the battery pack is handled improperly. Do not attempt to open or service the battery pack. Do not disassemble, crush, puncture, short external contacts or circuits, dispose of in fire or water, or expose a battery pack to temperatures higher than 60˚C (140˚F).
NOTE: For France, Headphones, Earphones (listed below) for this device have been tested to comply with the Sound Pressure Level requirement laid down in the applicable NF EN 50332-1:2000 and/or NF EN 50332-2:2003 standards as required by French Article L. 5232-1. 1. Earphone, manufactured by Cotron, Models CHM-60STV07002.
SAFETY PRECAUTIONS FOR RF EXPOSURE • Avoid using your device near metal structures (for example, the steel frame of a building). • Avoid using your device near strong electromagnetic sources, such as microwave ovens, sound speakers, TV and radio. • Use only original manufacturer-approved accessories, or accessories that do not contain any metal. • Use of non-original manufacturer-approved accessories may violate your local RF exposure guidelines and should be avoided.
GENERAL PRECAUTIONS • Heed service markings Except as explained elsewhere in the Operating or Service documentation, do not service any product yourself. Service needed on components inside these compartments should be done by an authorised service technician or provider.
• Mounting Accessories Do not use the product on an unstable table, cart, stand, tripod, or bracket. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. • Avoid unstable mounting Do not place the product with an unstable base. • Use product with approved equipment This product should be used only with personal computers and options identified as suitable for use with your equipment.
Contents Chapter 1 Getting Started 15 1.1 Getting to Know Your Device and Its Accessories ........... 16 1.2 About the SIM Card and Battery ..................................... 21 1.3 Starting Up........................................................................ 23 1.4 The Today Screen .............................................................. 25 1.5 Using the Programmes .................................................... 28 1.6 Device Settings ...................................
3.4 Smart Dialing .................................................................... 47 3.5 In-call Options .................................................................. 50 3.6 Additional Dialing Information ....................................... 51 3.7 Setting Up Bluetooth SIM Access for Car Kit Phones ..... 52 Chapter 4 Synchronising Information 53 4.1 About Synchronisation .................................................... 54 4.2 Using Microsoft Windows Mobile® Device Centre ..
Chapter 6 Getting Connected 85 6.1 Connecting to the Internet .............................................. 86 6.2 Internet Explorer Mobile ................................................. 89 6.3 Using Comm Manager...................................................... 92 6.4 Using Bluetooth................................................................ 93 6.5 Using Wi-Fi ...................................................................... 102 6.6 Using Internet Sharing ................
8.3 Using Windows Media Player Mobile ............................ 164 8.4 Using Audio Manager .................................................... 170 Chapter 9 Using Other Applications 177 9.1 Word Mobile ................................................................... 178 9.2 Excel Mobile .................................................................... 179 9.3 Viewing Slide Shows with PowerPoint Mobile ............. 180 9.4 Using Adobe Reader LE ...................................
Chapter 1 Getting Started 1.1 Getting to Know Your Device and Its Accessories 1.2 About the SIM Card and Battery 1.3 Starting Up 1.4 The Today Screen 1.5 Using the Programmes 1.
Getting Started 1.
Getting Started 17 No. Item Function 1 POWER Press and hold this button to turn on the device. When the device is turned on, press to turn off the display temporarily. This switches your device to Sleep mode, and you can still receive calls and messages. Press and hold (for about 5 seconds) to turn off the power completely. All functions including the phone will be unavailable for use. 2 SDTM Card Slot Insert a storage card (SD/MMC/SDIO card) for storing data.
Getting Started 21 24 22 23 25 19 26 20 27 28 29
Getting Started 19 No. Item Function 19 Back Cover This covers the battery and SIM card compartment. To remove, slide the latch that is located at the bottom of your device. 20 Back Cover Latch Press this latch to release the back cover. 21 Self-Portrait Mirror Turn the back side of your device to face yourself so that your image reflects on the mirror when taking self-portrait shots.
Getting Started Accessories 1 3 2 4 No. Accessory Function 1 AC adapter Recharges the battery. 2 USB Sync cable Connects your device to a PC and synchronises data. 3 Stereo headset Provides a volume control slider and a Send/End button. Press the Send/End button to pick up a call or put a call on hold; press and hold the button to end the call. 4 Pouch Acts as a protective carrying case for your device.
Getting Started 21 1.2 About the SIM Card and Battery Always turn off your device before installing/replacing the battery and SIM card. Follow the instructions in the Quick Start Guide to install a SIM (Subscriber Identity Module) card provided by your local network service provider and to install the battery. The SIM card contains your phone number, service details, and phonebook/ message memory. Your device supports both 1.8V and 3V SIM cards. Some legacy SIM cards will not function with your device.
Getting Started To check the battery power Do one of the following: • Tap the battery level icon ( • Alternatively, tap Start > Settings > System tab > Power. ) on the Today screen. Battery power information Charge the battery New batteries are shipped partially charged. Before you start using your device, it is recommended that you install and charge the battery. Some batteries perform best after several full charge/discharge cycles.
Getting Started 23 1.3 Starting Up Turn your device on and off To turn on your device, press and hold the POWER button. When you turn on your device for the first time, a Quick Start Wizard will guide you through the calibration process and the setup of regional settings, date and time, password, Outlook e-mail, and POP3/IMAP4 e-mail accounts. For more information about touch screen calibration, see “Calibrate the device”.
Getting Started Calibrate the device Calibrating the device screen involves tapping the centre of a cross with the stylus as the cross moves around the screen. This process ensures that when you tap the screen with your stylus, the tapped item is activated. If your device does not accurately respond to screen taps, follow these steps to re-calibrate it: 1. Tap Start > Settings > System tab > Screen. 2.
Getting Started 25 1.4 The Today Screen The Today screen displays important information, such as upcoming appointments and status indicators. You can tap a section on the screen to open the associated programme. • To access the Today screen, tap Start > Today. • To customise the Today screen display, including the background image, tap Start > Settings > Personal tab > Today. 2 345 1 6 7 8 9 10 11 12 13 14 15 16 1 Tap to open the Start menu. 2 Tap to view connectivity status.
Getting Started Indicators The following are some of the status icons that you may see on the device. Icon Description New e-mail or text messages; SMS notification of voice mail. New multimedia (MMS) message. New MSN message. There are more notifications. Tap the icon to view all. Voice call in progress. Call on hold. Calls are forwarded. Missed call. Dialing while no SIM card is inserted. Speakerphone on. Maximum signal strength. No signal. Phone is turned off. No phone service.
Getting Started 27 Icon Description Wi-Fi function enabled, but device not connected to a wireless network yet. Wireless network(s) detected. Connecting to wireless network (arrows moving); connected to wireless network. Synchronising via Wi-Fi. Battery is fully charged. Battery power is very low. Battery charging. Sound on. Sound off. Vibration mode. Alarm. No SIM card inserted. Device is locked. Device is unlocked. Bluetooth headset detected. GPRS Monitor currently active. Sprite Backup notification.
Getting Started The Start menu The Start menu, located at the top left corner of the Today screen, displays a list of programmes. You can start a programme by scrolling through the programmes list and then pressing ENTER, or by tapping a programme with the stylus. 1 2 3 4 5 6 1 Tap to switch to the Today screen. 2 Tap to start a programme. The items displayed in the Start menu can be customised by tapping Start > Settings > Personal tab > Menus. 3 Tap to start a recently-used programme.
Getting Started 29 1.5 Using the Programmes The following are some of the programmes that are already installed on your device. Icon Description ActiveSync Synchronises information between your device and a PC or the Exchange Server. Adobe Reader LE Enables you to view PDF (Portable Document Format) files on your device. Audio Manager Allows you to easily browse for music files by organising music files into categories such as artists, album, etc.
Getting Started Icon Description Help Enables you to see Help topics for the current screen or programme. Internet Sharing Allows you to connect your notebook computer to the Internet using your device's data connection. Internet Explorer Mobile Allows you to browse Web and WAP sites as well as download new programmes and files from the Internet. Messaging Allows you to send and receive e-mail, MMS, and text messages.
Getting Started 31 Icon Description Search Enables you to search contacts, data, and other information on your device. SIM Manager Allows you to manage the contacts that are stored on your SIM card. You can also use this programme to copy SIM contents to Contacts on your device. Spb GPRS Monitor Can be installed to your device from the disc. It measures the amount of data transfers that you have made via the GPRS or GSM network connection, and calculates network usage costs.
Getting Started 1.6 Device Settings You can adjust the device settings to suit the way you work. To see all available settings, tap Start > Settings, then tap the Personal, System, and Connections tabs located at the bottom of the screen. Personal tab Icon Description Buttons Assigns a programme or function to a hardware button. Input Sets options for each of the input methods. Lock Sets a password for your device. Menus Sets what programmes will appear in the Start menu.
Getting Started 33 System tab Icon Description About Allows you to specify a name for your device. Also shows the Windows Mobile version and copyright information. Backlight Sets the backlight timeout and brightness. Certificates Shows information about certificates that are installed on your device. Clear Storage Removes all your data and files from the memory and resets your device to factory default settings.
Getting Started Icon Description Remove Programs Lets you remove programmes that you installed on your device. Screen Allows you to change the screen orientation, re-calibrate the screen, and change the screen text size. Task Manager Allows you to configure the Exit button ( ) to end programmes and free up the memory that's occupied by them. Connections tab Icon Description Beam Enables your device to receive incoming infrared and Bluetooth beams.
Chapter 2 Entering and Searching Information 2.1 Entering Information 2.2 Using the On-screen Keyboard 2.3 Using Letter Recognizer 2.4 Using Block Recognizer 2.5 Using Transcriber 2.6 Using Notes to Draw, Write and Record Voice Notes 2.
Entering and Searching Information 2.1 Entering Information When you start a programme or select a field that requires text or numbers, the Input Panel icon becomes available on the menu bar. Tap the Input Selector arrow (that appears next to the Input Panel icon) to open a menu where you can select a text input method and customise input options. After selecting a text input method, the corresponding Input Panel is then displayed and you can use it to enter text.
Entering and Searching Information 37 2.2 Using the On-screen Keyboard The on-screen Keyboard is available when text entry is possible. You can enter text by tapping keys on the keyboard that are displayed on the screen. To enter text using the on-screen Keyboard 1. In a programme, tap the Input Selector arrow, and tap Keyboard. 2. Enter text by tapping keys on the on-screen Keyboard. To enlarge the on-screen Keyboard 1. Tap the Input Selector arrow, then tap Options. 2.
Entering and Searching Information 2.4 Using Block Recognizer With Block Recognizer, you use a single stroke to write letters, numbers, symbols, and punctuation, which are then converted into typed text. To use Block Recognizer 1. From a programme, tap the Input Selector arrow, and tap Block Recognizer. 2. Write characters, numbers, and symbols in the designated writing area. • Enter letters by writing in the abc (left) area of the box. • Enter numbers by writing in the 123 (right) area of the box.
Entering and Searching Information 39 To write using Transcriber 1. In a programme, position the cursor where you want text to appear. 2. Use the stylus to write anywhere on the screen. The handwriting will be converted to text shortly after you lift the stylus from the screen. To enter punctuation and symbols Transcriber comes with an on-screen keyboard that provides an easy way to add punctuation or a special symbol to existing text. • From a programme, tap on the Transcriber toolbar.
Entering and Searching Information 2.6 Using Notes to Draw, Write and Record Voice Notes Using Notes, you can draw directly on the screen, or write on the screen and save notes in your own handwriting. You can also create a stand-alone recording (voice note) or you can add a recording to a note. For more information on what you can do with Notes, please see “Notes” in Chapter 7. 2.
Chapter 3 Using Phone Features 3.1 Using the Phone 3.2 Making a Call 3.3 Receiving a Call 3.4 Smart Dialing 3.5 In-call Options 3.6 Additional Dialing Information 3.
Using Phone Features 3.1 Using the Phone Like a standard mobile phone, you can use your device to make, receive, and keep track of calls and send SMS/MMS messages. You can also dial directly from Contacts, and easily copy phonebook entries from your SIM card to Contacts on your device. The Phone screen From the Phone screen, you can access Call History, Speed Dial, and Phone settings. To open the Phone screen, do one of the following: • Tap Start > Phone. • Press the TALK button ( ).
Using Phone Features 43 Turn the phone function on and off In many countries, you are required by law to turn off your phone while on board an aircraft. To turn off the phone function Tap the Comm Manager icon ( following: • ) on the Today screen, then do one of the On the Comm Manager screen, tap the Phone button to turn off the icon indicates the phone function is phone function. The turned off.
Using Phone Features Notes • To adjust the conversation phone volume, you must do it during a call. Adjusting the volume at another time will affect the ring, notification, and MP3 sound levels. • When you activate Vibrate mode, sound will automatically be muted and your device will vibrate when an incoming call is received. The Vibrate ) will appear in the title bar to indicate that Vibrate mode is icon ( activated. 3.
Using Phone Features 45 Make a call from Contacts Tap Contacts on the Today screen or tap Start > Contacts, then do one of the following: • Press NAVIGATION up or down to select a contact, and press TALK. • Tap the desired contact in the contacts list, and tap the phone number that you want to call. • Tap and hold the desired contact, and on the shortcut menu, tap Call Work, Call Home, or Call Mobile.
Using Phone Features To create a Speed Dial entry 1. On the Phone screen, tap Speed Dial. 2. Tap Menu > New. 3. Tap a contact. Select the phone number that you want to add to Speed Dial. 4. In the Location box, select an available location for the new Speed Dial entry. Note Location 1 is generally reserved for your voice mail, and Speed Dial will designate the next available location by default.
Using Phone Features 47 3.3 Receiving a Call When you receive a phone call, a message will appear, giving you the option to either answer or ignore the incoming call. To answer or reject an incoming call • To answer the call, tap Answer, or press TALK on the device. • To reject the call, tap Ignore, or press END on the device. To end a call Once an incoming or outgoing call is in progress, you can tap End or press END on the device to hang up. 3.
Using Phone Features Tips on using Smart Dialing Smart Dialing starts looking for numbers or contacts that match the sequence you have entered. Below are some tips on how to use Smart Dialing to quickly find a desired phone number or contact. To find a phone number • Simply enter the first one or two digits to find a phone number in Call History. • Enter the first three digits or more if you want to find a phone number from the saved contacts on your device and SIM card.
Using Phone Features 49 4. Do one of the following: • When the correct contact is selected, tap Talk or press the TALK ) to make a voice call. button ( • To send a text message to the selected contact, tap and hold the contact, and tap Send Text Message. • To call a different phone number associated with the selected contact, tap and hold the selected contact, and tap the phone number you want to call. Tap and hold the contact to pop up the shortcut menu.
Using Phone Features • • Select the Enable double-click for dialing check box to make a voice call by double-tapping the item in the matched list. In Scroll unit, you can set the amount of scrolling when tapping / ). the arrows ( 3.5 In-call Options To put a call on hold Your device notifies you when you have another incoming call, and gives you the choice of rejecting or accepting the call.
Using Phone Features 51 Warning! To avoid damage to your hearing, do not hold your device against your ear when the Speakerphone is turned on. To mute a call You can turn off the microphone during a call, so that you can hear the caller but the caller cannot hear you. • During a call, tap Mute. • When the microphone is turned off, the mute icon ( ) appears on the screen. Tap Unmute to turn on the microphone again. 3.
Using Phone Features 3.7 Setting Up Bluetooth SIM Access for Car Kit Phones Car kit phones that support the SIM Access Profile (SAP) can connect to your device and access its SIM card via Bluetooth. Once a SAP connection has been established, you can download SIM contacts from your device to the car kit phone. You can also use the car kit phone to answer and make calls using your device’s SIM card.
Chapter 4 Synchronising Information 4.1 About Synchronisation 4.2 Using Microsoft Windows Mobile® Device Centre 4.3 Installing and Using Microsoft ActiveSync® 4.4 Synchronising with Your Computer 4.5 Synchronising with Exchange Server 4.6 Synchronising via Infrared and Bluetooth 4.
Synchronising Information 4.1 About Synchronisation You can take information from your computer wherever you go by synchronising them to your device.
Synchronising Information 55 4.2 Using Microsoft Windows Mobile® Device Centre Microsoft Windows Mobile® Device Centre is the replacement for Microsoft® ActiveSync® on Windows Vista™. Set up synchronisation When you connect your device to your PC and start Windows Mobile Device Centre for the first time, you are asked to create a Windows Mobile partnership with your device. Follow the steps below to create a partnership. 1. Connect your device to your PC.
Synchronising Information 4. Select the information types that you want to synchronise then click Next. 5. Enter a device name and click Set Up. When you finish the setup wizard, Windows Mobile Device Centre synchronises your device automatically. Notice that Outlook e-mails and other information will appear on your device after synchronisation.
Synchronising Information 57 Use Windows Mobile Device Centre To start using Windows Mobile Device Centre, click Start > All Programs > Windows Mobile Device Centre. Importing photos and other media from your device to your PC is fast and easy. When you click Import pictures/video from your device on the Home screen, a wizard guides you to tag and transfer photos from your device to the Photo Gallery on your Windows Vista PC.
Synchronising Information 4.3 Installing and Using Microsoft ActiveSync® Follow the steps below to install and set up ActiveSync 4.x on Windows XP or other compatible Windows systems. Note For a list of compatible Windows systems, please go to http://www.microsoft. com/windowsmobile/activesync/activesync45.mspx. Install ActiveSync 1. Insert the Getting Started Disc into the disc drive on your PC. 2. ActiveSync is available in English and several other languages.
Synchronising Information 59 4.4 Synchronising with Your Computer Connect your device to the PC using the USB cable, infrared, or Bluetooth connection. Windows Mobile Device Centre or ActiveSync then opens and lets you synchronise. Tip If you are synchronising directly with Exchange Server, you can use this connection to the PC to "pass through" to the network, or you can synchronise without connecting to the PC over a cellular network.
Synchronising Information 1. In ActiveSync on your device, tap Menu > Options. 2. Select the check box for any items you want to synchronise. If you cannot select a check box, you might have to clear the check box for the same information type elsewhere in the list. 3. To change synchronisation settings for an information type, for instance, E-mail, select it and tap Settings. You can then set the download size limit, specify the time period of information to download, and more.
Synchronising Information 61 4.5 Synchronising with Exchange Server You can set up synchronisation with Exchange Server on your device, if it is available to you through your company or wireless service provider. However, you should first gather information, such as Exchange Server name, domain name, your user name, and password, and then carry on with the steps. (For information about how to check the Exchange server name and domain on your PC, see “Installing and Using Microsoft ActiveSync.
Synchronising Information To receive e-mails and synchronise other information instantly Direct Push technology (push e-mail feature) enables you to receive new e-mails on your device as soon as they arrive in your Inbox on the Exchange Server. With this feature, items such as contacts, calendar and tasks are also immediately updated onto your device when these items have been changed or new entries have been added on the Exchange Server.
Synchronising Information 63 Note When both the GPRS and Wi-Fi connections are turned on at the same time, the Direct Push feature will always opt for GPRS, for which you could be charged per your network operator’s service plan. To schedule synchronisation at regular time intervals You can set how often to synchronise during Peak times (which usually refer to your working hours) when e-mail volume is high, as well as Offpeak times when e-mail volume is low. 1.
Synchronising Information 3. Tap Menu > Connect via Bluetooth. Make sure the Bluetooth function of both your device and the computer are turned on and set to visible mode. 4. If this is the first time you have connected to this computer via Bluetooth, you must first complete the Bluetooth wizard on your device and set up a Bluetooth partnership between your device and the computer. For more information about creating a Bluetooth partnership, see “Bluetooth partnerships” in Chapter 6.
Chapter 5 Managing Your Pocket PC Phone 5.1 Personalising Your Pocket PC Phone 5.2 Adding and Removing Programmes 5.3 Managing Memory 5.4 Copying and Managing Files 5.5 Backing Up Data 5.6 Protecting Your Pocket PC Phone 5.
Managing Your Pocket PC Phone 5.1 Personalising Your Pocket PC Phone Customise the Today screen The Today screen shows your upcoming appointments, active tasks, and information about incoming messages. You can customise the Today screen on your device. To customise the Today screen 1. Tap Start > Settings > Personal tab > Today. 2. On the Appearance tab, select the desired theme for the background of the Today screen. 3. On the Items tab, select the items you want to appear on the Today screen.
Managing Your Pocket PC Phone 67 4. Do any of the following: • Select Next appointment to show only the next appointment in your schedule, or Upcoming appointments to show multiple appointments. • Clear the Display all day events check box if you do not want to display all-day events. To set options for displaying tasks on the Today screen If you have a large number of tasks, you may want to specify the kind of tasks that are displayed on the Today screen. 1. Tap Start > Settings > Personal tab > Today. 2.
Managing Your Pocket PC Phone Why is the device name important? The device name is used to identify the device in the following situations: • Synchronising with a PC • Connecting to a network • Restoring information from a backup Note If you synchronise multiple devices with the same PC, each device must have a unique name. To change the device name 1. Tap Start > Settings > System tab > About. 2. Tap the Device ID tab. 3. Enter a name.
Managing Your Pocket PC Phone 69 5. Tap the alarm icon ( ) to specify the type of alarm you want. You can choose a flashing light, a single sound, a repeating sound, or vibration. 6. If you choose to play a sound, tap the list next to the Play sound check box and tap the sound you want. To set the time and date for a different location If you visit or communicate with someone in a particular time zone often, you can select it as your visiting time zone. 1.
Managing Your Pocket PC Phone 3. Tap the button you want to reassign. To help you identify the buttons, there are numbers and icons representing the original function of the button. 4. In the Assign a program box, tap the programme or shortcut you want to assign. 5. Tap OK. To increase or decrease the size of text on the screen 1. Tap Start > Settings > System tab > Screen > Text Size tab. 2. Move the slider to increase or decrease the text size. To choose how to be notified about events or actions 1.
Managing Your Pocket PC Phone 71 To make the battery last longer • Tap the battery icon ( ) on the Today screen. On the Advanced tab of the Power settings screen, you can specify when your device turns off the display to conserve battery power. For optimum conservation, specify 3 minutes or less. • Use the AC adapter to plug your device into external power whenever possible, especially when using an SD card or when using a modem or other peripherals. • Adjust the backlight settings.
Managing Your Pocket PC Phone Phone settings You can customise phone settings, such as the ring type and ring tone to be used for incoming calls, and the keypad tone to be used when entering phone numbers. Open the Phone programme to customise these settings. To change the ring tone 1. On the Phone screen, tap Menu > Options > Phone tab. 2. In the Ring tone list, tap the sound you want to use. Tip To use custom *.wav, *.mid, *.mp3, or *.
Managing Your Pocket PC Phone 73 Networks You can view available mobile phone networks, determine the order in which your device accesses another network if the current one is unavailable, and specify whether you want to change networks manually or automatically. For more information about network settings, see Help on your device. To change phone network settings 1. Tap Start > Settings > Personal tab > Phone > Network tab. 2.
Managing Your Pocket PC Phone To add programmes 1. Download the programme to your PC (or insert the CD or disc that contains the programme into your PC). You may see a single *.exe file, a *.zip file, a Setup.exe file, or several versions of files for different device types and processors. Be sure to select a programme designed for your device and processor type. 2. Read any installation instructions or documentation that comes with the programme. Many programmes provide special installation instructions. 3.
Managing Your Pocket PC Phone 75 5.3 Managing Memory You may need to stop a programme if it becomes unstable or the programme memory is low. To see how much memory is available • Tap Start > Settings > System tab > Memory. • On the Main tab, the amount of memory allocated to file and data storage versus programme storage is displayed, as well as the amount of memory in use versus the available memory.
Managing Your Pocket PC Phone To close a programme Tapping the button in a programme may just close the programme screen. In this case, the programme continues to run in the background. You can end running programmes manually by following these steps: 1. Tap Start > Settings > System tab > Memory > Running Programs tab. 2. In the Running Programs List, tap the programme you want to close, and tap Stop.
Managing Your Pocket PC Phone 77 5. To copy a file from your PC to your device: a. On your PC, navigate to the folder that contains the file you want to copy. b. Right-click the file, then click Copy. c. Right-click the destination folder under Mobile Device, then click Paste. Copying a file results in separate versions of a file on your device and PC. Because the files are not synchronised, changes made to one file will not affect the other.
Managing Your Pocket PC Phone To automatically save files on a storage card In the Word Mobile, Excel Mobile, and Notes programmes, you may find it helpful to save all new documents, notes, and workbooks directly on a storage card. 1. From the programme file list, tap Menu > Options. 2. With a storage card inserted in your device, in the Save to box, select the appropriate storage card to automatically save new files on the storage card. 3. Tap OK.
Managing Your Pocket PC Phone 79 Basic mode Advanced mode Basic mode Basic mode is the default mode, and allows you to easily back up your entire Pocket PC with the tap of a button. Note To change backup options or location, you will need to do it in Advanced mode. To back up data in Basic mode 1. On the Basic mode screen, tap Backup Now. 2. Specify a password (between 6 to 15 characters in length) for the backup file. Enter this password twice, then tap OK. 3.
Managing Your Pocket PC Phone To back up data in Advanced mode 1. Tap Options > Switch to Advanced Mode. 2. The Backup tab of the Advanced mode screen shows a tree view of the data and files on your device. Tap the ‘+’ symbol at the left of an item to view its sub-items. Use the check boxes to select or exclude items for backup. 3. Tap Backup and follow the on-screen instructions to complete the backup. To restore data in Advanced mode 1. On the Advanced mode screen, tap the Restore tab. 2.
Managing Your Pocket PC Phone 81 3. Before you perform a backup, tap then specify a backup file name. To schedule automatic backups 1. Tap Options > Scheduled Backup, then tap Change Scheduling. 2. Select the Enable Scheduled Backup check box, and set the frequency of backups to perform, date and time, and other options. 3. Tap OK. To enable remote backups to the computer via ActiveSync 1. Tap Options > Networking. 2. Select the Enable Remote Backup check box. 3. Select Via ActiveSync, then tap OK. 4.
Managing Your Pocket PC Phone To protect your device with a password 1. Tap Start > Settings > Personal tab > Lock. 2. Select the Prompt if device unused for check box, and in the box to the right, select how long your device must be idle before a password is required. In the Password type box, select the type of password you would like to use. Enter the password and, if necessary, confirm the password.
Managing Your Pocket PC Phone 83 3. If you want additional text displayed, tap the Notes tab and enter the text (for instance: Reward if found). 4. On the Options tab, select the Notes check box. 5. Tap OK. Tip To display owner information on the Today screen, tap Start > Settings > Personal tab > Today. On the Items tab, select the Owner Info check box. 5.7 Resetting Your Pocket PC Phone Occasionally, you may need to reset your device.
Managing Your Pocket PC Phone To perform a hard reset 1. Press and hold the left SOFT KEY and the right SOFT KEY, and at the same time, use the stylus to press the RESET button at the bottom of your device. 2. Release the stylus, but continue pressing the two SOFT KEYs until you see the following message on the screen: Press SEND to restore factory default, press END to quit. 3. Release the two SOFT KEYs, and then press the device.
Chapter 6 Getting Connected 6.1 Connecting to the Internet 6.2 Internet Explorer Mobile 6.3 Using Comm Manager 6.4 Using Bluetooth 6.5 Using Wi-Fi 6.6 Using Internet Sharing 6.7 Using Spb GPRS Monitor 6.
Getting Connected 6.1 Connecting to the Internet Your device is equipped with powerful networking functions that enable you to connect to the Internet through Wi-Fi, GPRS (General Packet Radio Service) or the mobile phone network. Connecting your device to the Internet through a private or free wireless network is your best choice since this will not incur any cost. Take note, however, that using Wi-Fi on your device will drain battery power faster.
Getting Connected 87 5. Enter the Access point name, then tap Next. 6. Enter the user name and password, only if required. 7. Tap Finish. Notes • To view help information for any screen, tap the help icon ( ). • To modify your connection settings, tap Manage existing connections on the Connections screen, and complete the connection wizard.
Getting Connected To set up a dial-up connection to your ISP When you use your device to dial up to your ISP and connect to the Internet, you will be billed by the number of minutes that you use. To establish a dial-up connection on your device, you need the same settings that you normally use when you dial up from your computer. This includes the ISP server phone number, your user name and password. 1. Tap Start > Settings > Connections tab > Connections. 2. Under My ISP, tap Add a new modem connection.
Getting Connected 89 If you have set up multiple types of connections on your device, you can manually start a connection. 1. Tap Start > Settings > Connections tab > Connections. 2. Tap Manage existing connections. 3. Tap and hold the name of the desired connection, then tap Connect. To disconnect the GPRS connection Do one of the following: • Tap the Comm Manager icon ( Data Connection button ( • Press and hold END ( ) on the Today screen, then tap the ). ) on your device for at least three seconds.
Getting Connected 1. In Windows Mobile Device Centre or ActiveSync on your PC, on the Tools menu, click Options, and select Favorites. 2. In Internet Explorer on your PC, click Favorites > Add to Favorites and save or move favourite links to the Mobile Favorites subfolder in the Favourites list. 3. Connect your device to your PC. If synchronisation does not start automatically, click Sync. To add a favourite 1. In Internet Explorer Mobile, go to the page you want to add. 2.
Getting Connected 91 To clear the History list 1. In Internet Explorer Mobile, tap Menu > Tools > Options > Memory tab. 2. Tap Clear History. To save a picture from a Web page 1. In Internet Explorer Mobile, tap and hold the picture, and tap Save Image. 2. Do one of the following: • To save the picture in My Pictures on your device, tap Yes. • To save the picture in another location, such as a storage card, tap Save As.
Getting Connected 6.3 Using Comm Manager Comm Manager acts like a central switcher that lets you enable or disable phone features as well as manage your data connections easily. To open Comm Manager • Tap the Comm Manager icon ( • ) on the Today screen; or Tap Start > Settings > Connections tab > Comm Manager. Simply tap the corresponding button to enable or disable a feature. 1 5 2 6 3 7 4 8 1 Tap to toggle between turning on or off Flight mode.
Getting Connected 93 6.4 Using Bluetooth Bluetooth is a short-range wireless communications technology. Devices with Bluetooth capabilities can exchange information within a distance of about 10 metres without requiring a physical connection. You can even beam information to a device in a different room, as long as it is within the Bluetooth signal coverage range.
Getting Connected Note By default, Bluetooth is turned off. If you turn it on, then turn off your device, Bluetooth also turns off. When you turn on your device again, Bluetooth automatically turns on. To turn Bluetooth on and make your device visible 1. On your device, tap Start > Settings > Connections tab > Bluetooth. 2. Select the Turn on Bluetooth and Make this device visible to other devices check boxes. 3. Tap OK.
Getting Connected 95 To accept a Bluetooth partnership 1. Ensure that Bluetooth is turned on and in visible mode. 2. Tap Yes when prompted to establish a partnership with the other device. 3. Enter a passcode (the same passcode that is entered on the device requesting the partnership) to establish a secure connection. The passcode must be between 1 and 16 characters. 4. Tap Next. 5. Tap Finish. You can now exchange information with the paired device. To rename a Bluetooth partnership 1.
Getting Connected To connect a Bluetooth hands-free or stereo headset 1. Make sure that both your device and the Bluetooth headset are turned on and within close range, and that the headset is visible. Refer to the manufacturer’s documentation to find out how to set the headset in visible mode. 2. Tap Start > Settings > Connections tab. 3. Tap Bluetooth > Devices tab > Add new device. Your device searches for other Bluetooth-enabled devices and displays them in the list. 4.
Getting Connected 97 Beam information using Bluetooth You can beam information, such as contacts, calendar items, and tasks, as well as files from your device to your computer or to another Bluetoothenabled device. Note If your computer does not have built-in Bluetooth capability, you need to connect and use a Bluetooth adapter or dongle on your computer. To beam information from your device to a computer 1. Turn on Bluetooth on your device, and make your device visible.
Getting Connected 5. To beam a contact, tap Menu > Send Contact > Beam. To beam other types of information, tap Menu > Beam [type of item]. 6. Tap the device name to which you want to send the beam. 7. If you beamed an Outlook item and it is not automatically added to Outlook, select File > Import and Export in Outlook to import it. To beam information to a Bluetooth-enabled device such as another Pocket PC, follow steps 3 to 6 in the above procedure.
Getting Connected 99 3. Select the Enable File Sharing check box. You can use the default Bluetooth shared folder, or tap Browse to use another folder as your shared folder. To use Bluetooth Explorer 1. Bluetooth Explorer is integrated with the File Explorer programme. You can open it by tapping Start > Programs > Bluetooth Explorer or by tapping Down arrow ( ) on the upper left of File Explorer then tapping Bluetooth. 2.
Getting Connected Use the device as a Bluetooth modem You can connect your device to a notebook or desktop computer through Bluetooth and use the device as a modem for the computer. Note If your computer does not have built-in Bluetooth capability, you need to connect and use a Bluetooth adapter or dongle on your computer.
Getting Connected 101 5. From the Network Connection list, select the name of the connection that your device uses to connect to the Internet. 6. Tap Connect. 7. On your computer, set up a Bluetooth Personal Area Network (PAN) with your device: a. Tap Start > Control Panel > Network Connections. b. Under Personal Area Network, click the Bluetooth Network Connection icon. c. Under Network Tasks, click View Bluetooth network devices. d.
Getting Connected To use a Bluetooth phone as a modem for your device 1. On your device, tap Start > Settings > Connections tab > Connections. 2. Tap Add a new modem connection. 3. Enter a name for the connection. 4. In the Select a modem list, tap Bluetooth. 5. Tap Next. 6. If the phone appears in the My Connections list, skip to step 11. 7. If the phone does not appear in the My Connections list, tap Add new device, and follow the remaining steps. 8. Select the phone from the list and tap Next. 9.
Getting Connected 103 To connect to a wireless network 1. Open the Comm Manager. 2. Tap the WLAN button to turn on/off the wireless function. The WLAN icon indicates the wireless status. : Wi-Fi is turned on. : Wi-Fi is turned off. 3. After Wi-Fi has been turned on, your device then scans for available wireless networks in your area. The network names of the detected wireless networks will be displayed on a pop-up message window. Tap the desired wireless LAN, then tap OK. 4.
Getting Connected Next time you use your device to detect wireless networks, you will not see the pop-up message windows again, and you will not be prompted to enter the network key of the previously accessed wireless network (unless you perform a hard reset which will erase custom settings on your device). Note Wi-Fi networks are self-discoverable, which means no additional steps are required for your device to connect to a Wi-Fi network.
Getting Connected 105 To check the wireless LAN status You can check the current wireless connection status from the following three screens of your device: • Title bar. When you enable Wi-Fi on your device, the Wi-Fi ON icon ( ) will appear on the title bar of the Today screen. After Wi-Fi is turned on, your device scans for available wireless networks and the wireless signal icon ( ) appears on the title bar.
Getting Connected 6.6 Using Internet Sharing Internet Sharing connects your PC or notebook computer to the Internet by using your device’s data connection (GPRS for instance). You can choose to connect via USB or Bluetooth. Follow the procedure in this section to set up your device as a USB modem. To learn how to set up your device as a Bluetooth modem, see “Use the device as a Bluetooth modem” in this chapter.
Getting Connected 107 6.7 Using Spb GPRS Monitor Spb GPRS Monitor measures the amount of data transfers that you have made via GPRS or a phone dial-up connection, and calculates network usage costs. Using this programme, you can monitor how much data you have sent and received on your device, and check the network usage costs by taking into account your service plan details: inclusive data amount, data block size, etc.
Getting Connected To show or hide items on the Today Plug-in 1. Tap Start > Settings > Personal tab > Today. 2. On the Items tab, tap GPRS Monitor then tap Options. 3. On the Display tab, specify the refresh interval for updating statistics, time period for monitoring data transfers, and the types of information to be shown on the plug-in. 4. On the Additional Items tab, choose whether to show or hide the brightness panel, battery panel, and shortcut icons on the plug-in. 5. Tap OK.
Getting Connected 109 To customise the GPRS Monitor pop-up window When you tap the GPRS Monitor icon on the title bar, a pop-up window opens and shows you detailed statistics about data transfers, such as the data size just transferred and its cost, the data amount left that you are allowed to transfer, and more. On the GPRS Monitor screen, tap Tools > Options > Popup tab to choose what types of statistics to show on the pop-up window.
Getting Connected Options: Tariff tab Options: Tariff Details tab To set up traffic limit notifications You can set up traffic limit notifications if you want to be notified when a traffic limit is reached. 1. On the GPRS Monitor screen, tap Tools > Options. 2. Enable the notifications on the Day Warn and Month Warn tabs. You can specify up to three daily and three monthly limits. Once traffic reaches one of these limits, you will receive a notification.
Getting Connected 111 4. Enter the tariffs that you are charged for this connection. For more information about tariffs, see “To enter service plan details”. 5. Repeat steps 1 to 4 to configure more profiles. 6. When you have finished profile setup, tap OK. To switch between profiles 1. On the GPRS Monitor screen, tap Tools > Profiles. 2. Select your desired profile, or select Auto change profile to enable the GPRS Monitor to automatically change to an active profile based on the connection you are using. 3.
Getting Connected 6.8 Using Terminal Services Client The Terminal Services Client allows you to log on to a PC running Terminal Services or Remote Desktop, and use all the resources available on that PC. For example, instead of running Word Mobile on your device, you can run the PC version of Word and access the .doc files available on that PC. To connect to a Terminal Server 1. On your device, tap Start > Programs > Terminal Services Client. 2. Enter the server name. 3.
Getting Connected 113 Notes • • Do not use the Start menu on your device. If a network administrator has configured Terminal Services Client on your device to reconnect to disconnected sessions, and you previously disconnected from a Terminal Server without ending the session, the Terminal Services Client reconnects to that session. To disconnect after ending a session 1. From the Terminal Services Client screen on your device, tap Start > Shutdown. 2. Tap Log Off.
Getting Connected
Chapter 7 Exchanging Messages and Using Outlook 7.1 E-mail and Text Messages 7.2 MMS Messages 7.3 Pocket MSN 7.4 Calendar 7.5 Contacts 7.6 Tasks 7.7 Notes 7.
Exchanging Messages and Using Outlook 7.1 E-mail and Text Messages Messaging is where all of your e-mail accounts and your text message account are located. You can send and receive Outlook e-mail, Internet e-mail through an Internet service provider (ISP), as well as SMS (Short Messaging Service) text messages using your mobile phone network. You can also access e-mail from work using a VPN connection.
Exchanging Messages and Using Outlook 117 1. To synchronise remotely, you need to set up and connect to an overthe-air connection (GPRS or ISP dial-up). For more details, see the procedures in “Connecting to the Internet” in Chapter 6. 2. Disconnect your device from your computer or LAN. (If you have an over-the-air connection, there is no need to disconnect). 3. Tap Start > Programs > ActiveSync. 4.
Exchanging Messages and Using Outlook 6. Enter your name (the name you want displayed when you send email), user name, and password; tap Next. Select the Save password check box if you want to save your password so that you do not need to enter it again. If Auto configuration was successful, the Your name and User name fields automatically get populated. Tap Next, then Finish to complete setting up your account, or tap Options under Server information to access additional settings.
Exchanging Messages and Using Outlook 119 Setting Outgoing mail requires authentication Use separate settings Description Select this if your outgoing e-mail server (SMTP) requires authentication. Your user name and password from above will be used. Select this if your outgoing e-mail server requires a different user name and password than the ones you entered before. Outgoing server settings: User name Enter your user name for the outgoing e-mail server.
Exchanging Messages and Using Outlook Tips • To enter symbols, tap Shift using the on-screen keyboard. • To set the priority, tap Menu > Message Options. • If you are working offline, e-mail messages are moved to the Outbox folder and will be sent the next time you connect. • If you are sending a text message and want to know if it was received, before composing the message, tap Menu > Tools > Options. Tap Text Messages and select the Request delivery notifications check box.
Exchanging Messages and Using Outlook 121 To receive attachments An attachment sent with an e-mail message or downloaded from the server appears below the subject of the message. Tapping the attachment opens the attachment if it has been fully downloaded, or marks it for download the next time you send and receive e-mail. You can also download attachments automatically with your messages if you have an Exchange Server mail account. If you have an Outlook e-mail account, do the following: 1.
Exchanging Messages and Using Outlook e-mail server. For more information, see “To download messages from the server” later in this chapter. • Text messages are automatically received when the phone is turned on. When the phone is turned off, messages are held by your service provider until the next time the phone is turned on.
Exchanging Messages and Using Outlook 123 Set up e-mail security Windows Mobile on your device protects your Outlook e-mails through Secure/Multipurpose Internet Mail Extension (S/MIME), which allows you to digitally sign your messages as well as encrypt them. Using authorisation keys and certificates, S/MIME allows you to digitally sign your e-mail messages to prove your identity to the recipients.
Exchanging Messages and Using Outlook Individually sign and encrypt a message Encrypting an Outlook e-mail message protects the privacy of the message by converting it from plain, readable text into cipher (scrambled) text. Only the recipient who has the authorisation key can decipher the message. Digitally signing a message applies your certificate with the authorisation key to the message.
Exchanging Messages and Using Outlook 125 Note There can be several reasons why a digital signature is not valid. For example, the sender’s certificate may have expired, it may have been revoked by the certificate authority, or the server that verifies the certificate is unavailable. Contact the sender to report the problem. Manage folders Each Messaging account has its own folder hierarchy with five default Messaging folders: Inbox, Outbox, Deleted Items, Drafts, and Sent Items.
Exchanging Messages and Using Outlook 7.2 MMS Messages Creating and sharing multimedia messages (MMS) with your friends and family are easy with your device. You can attach pictures or video, and an audio clip in an MMS. You can even use the device camera to capture photos and video clips while composing a new MMS message, and send them along with your message. Notes • Please note that MMS is a charged service. In order to use MMS successfully, this has to be provisioned on your mobile account.
Exchanging Messages and Using Outlook 127 4. In the Preferences tab, select or clear the provided check boxes according to your needs. You can choose to keep track of your MMS messages, retrieve messages immediately, accept or reject messages, and request a delivery or read receipt. You can also specify a resolution for images you send and message delivery attempts. 5. Tap the Servers tab and check if your device is preset with MMS server settings.
Exchanging Messages and Using Outlook Note If you add several MMS service providers to the MMS Configuration screen, you can choose one as your default MMS provider. Select the MMS provider's name in the list then tap Set As Default. Create and send MMS messages After configuring the required settings, you can start to compose and send MMS messages.
Exchanging Messages and Using Outlook 129 Repeat steps 5 and 6 to insert a photo/video, text, and audio into each slide that you added. While on a slide, you can: • Tap to preview the slide. • Tap to go to the previous slide. • Tap to go to the next slide. 8. While composing an MMS message, you can also do the following: • Tap Menu > Options > Background to choose a background colour from the list.
Exchanging Messages and Using Outlook To add text to an MMS message When entering text into an MMS message, you can do the following: • Tap inside the text box and enter your own text. • Choose from common words or phrases. Tap from the My Text list. • Tap • You can easily include a Web page link. Tap then select a Web page address from the Internet Favourites list on your device. Tip to add a text string to add an emoticon.
Exchanging Messages and Using Outlook 131 View and reply MMS messages To view an MMS message • Use the playback controls • , , and . Tap Objects to see a list of files included in the message. On the Message Objects screen, you can do the following: • To save a file, select it, and tap Menu > Save. • To save the contents of a text file to the My Text list, tap Menu > Save into “My Text”. • To associate a photo to one of your contacts, tap Menu > Assign to Contact.
Exchanging Messages and Using Outlook To start MSN Messenger 1. Tap Start > Programs > Pocket MSN. 2. Tap MSN Messenger. To sign in or out • To sign in, tap anywhere on the MSN Messenger screen. Enter the email address and password for your Passport or Hotmail account, and tap Sign In. Signing in may take several minutes, depending on your connection speed. • To sign out, tap Menu > Sign Out. Your status changes to Offline.
Exchanging Messages and Using Outlook 133 To schedule an appointment 1. Tap Start > Calendar. 2. Tap Menu > New Appointment. 3. Enter a name for the appointment, and enter information such as start and end times. 4. To schedule an all-day event, in the All Day box, tap Yes. 5. When finished, tap OK to return to the calendar. Notes • All-day events do not occupy blocks of time in Calendar; instead, they appear in banners at the top of the calendar.
Exchanging Messages and Using Outlook 2. Tap Menu > Options > Appointments tab. 3. Select the Set reminders for new items check box. 4. Set the time when you want the reminder to alert you. 5. Tap OK to return to the calendar. 7.5 Contacts Contacts is your address book and information storage for the people and businesses you communicate with. Store phone numbers, e-mail addresses, home addresses, and any other information that relates to a contact, such as a birthday or an anniversary date.
Exchanging Messages and Using Outlook 135 3. Tap Save to save the information on your SIM card. To change contact information 1. Tap Start > Contacts. 2. Tap the contact. 3. Tap Menu > Edit and enter the changes. 4. When finished, tap OK. Tip: To change contact information on your SIM card, tap Start > Programs > SIM Manager, then tap a SIM contact and edit it. After modifying, tap Save. To work with the contact list There are several ways to use and customise the contact list. Here are a few tips: 1.
Exchanging Messages and Using Outlook To copy contacts to the SIM card Only one phone number per contact name can be stored on a SIM card. When you copy a contact that has several phone numbers to your SIM card, SIM Manager saves each number under a separate name. To save each number under a different contact name on the SIM card, SIM Manager appends an indicator at the end of each name. By default, /M, /W and /H are appended to indicate mobile, work and home phone numbers respectively.
Exchanging Messages and Using Outlook 137 • Filter the list by categories. In the contact list, tap Menu > Filter, then tap a category you’ve assigned to a contact. To show all contacts again, select All Contacts. To find a contact online In addition to having contacts on your device, you can also access contact information from your organisation’s Global Address List (GAL).
Exchanging Messages and Using Outlook 4. Enter the part or full contact name and tap Find. Tap Select to choose the desired contact(s) from the list. Notes • Your device must be set up with a data connection. • You can search on the following information as long as that information is included in your organisation’s GAL: First name, Last name, E-mail name, Display name, E-mail address, or Office location. To send contact information via text messaging 1. Tap Start > Contacts, then select a contact.
Exchanging Messages and Using Outlook 139 2. Tap Menu > New Task, enter a subject for the task, and fill in information such as start and due dates, priority, and so on. 3. When finished, tap OK. Tip You can easily create a short, to-do type task. Simply tap the Tap here to add a new task box, enter a subject, and tap the Enter button on the on-screen keyboard. If the task entry box is not available, tap Menu > Options and select the Show Tasks entry bar check box.
Exchanging Messages and Using Outlook To locate a task When your list of tasks is long, you can display a subset of the tasks or sort the list to quickly find a specific task. 1. Tap Start > Programs > Tasks. 2. In the task list, do one of the following: • Sort the list. Tap Menu > Sort By, and tap a sort option. • Filter the list by category. Tap Menu > Filter, and tap the category you want displayed. Tip To filter your tasks further, tap Menu > Filter > Active Tasks or Completed Tasks. 7.
Exchanging Messages and Using Outlook 141 To create a note 1. Tap Start > Programs > Notes. In the note list, tap New. 2. Tap the Input Selector arrow next to the Input Method icon on the menu bar, tap the input method you want, and enter your text. 3. If the Input Selector arrow is not displayed, tap the Input Method icon. 4. When finished, tap OK to return to the note list. Notes • To select handwritten text, tap and hold next to the writing.
Exchanging Messages and Using Outlook Record a voice note You can create a stand-alone recording (voice note) or you can add a recording to a note. To create a voice note 1. Tap Start > Programs > Notes. 2. Do one of the following: • To create a stand-alone recording, record from the note list. • To add a recording to a note, create or open a note. 3. If you do not see the Recording toolbar, tap Menu > View Recording Toolbar. 4. Tap the Record icon ( ) to begin recording. 5.
Exchanging Messages and Using Outlook 143 7.8 Voice Recorder Voice Recorder lets you record your voice and then quickly send it via MMS or e-mail, beam it or set the recorded voice as your ringtone. Note Voice Recorder saves voice recordings in AMR-NB (Adaptive Multi-Rate Narrowband) format only. This is a common speech audio format used in mobile devices. To record your voice 1. On the Today screen, tap Start > Programs > Voice Recorder. 2. Hold the device’s microphone near your mouth. 3.
Exchanging Messages and Using Outlook To send the voice recording via e-mail 1. On the Voice Recorder screen, select the voice recording you want to send via e-mail. 2. Tap Menu > Send > Outlook E-mail. This automatically opens the Outlook E-mail with the voice recording automatically inserted as an attachment for the e-mail. See “Send and receive messages” in this chapter to learn how to compose and send e-mails. To beam the voice recording 1.
Chapter 8 Experiencing Multimedia 8.1 Using Camera 8.2 Using Pictures & Videos 8.3 Using Windows Media Player Mobile 8.
Experiencing Multimedia 8.1 Using Camera Taking photos and recording video clips along with audio are easy with your device’s built-in camera. Now you can use this 2.0 Megapixels camera to capture high resolution pictures and video clips accompanying audio. The camera also supports the macro function which enables you to take close-up shots of a subject.
Experiencing Multimedia 147 The available capture modes of the camera are as follows: • Photo: Captures standard still images. • Video: Captures video clips, with or without accompanying audio. • MMS Video: Captures video clips suitable for sending via MMS. • Contacts Picture: Captures a still image and gives you the option to immediately assign it as a Photo ID for a contact. • Picture Theme: Captures still images and places them within frames.
Experiencing Multimedia • • • • • Press the CAMERA button or the ENTER button to take a photo or contacts picture. Press the CAMERA button or the ENTER button to start recording video; press it again to stop recording. Press the CAMERA button or the ENTER button each time when taking photos for a picture theme or panorama. To take consecutive shots in Sports mode, press the CAMERA button or the ENTER button shortly, then move your device to follow the movement of your subject.
Experiencing Multimedia 149 4 Storage. Tap to toggle between saving captured photos or video clips on the device memory ( ) or on the memory card ( ). 5 Remaining information indicator. In Photo, Contacts Picture, Picture Theme, Sports, and Burst modes, this shows the remaining, available shots of pictures based on current settings. In Video and MMS Video modes, this shows the remaining duration that can be recorded. While recording video, this shows the recorded duration. 6 Zoom control.
Experiencing Multimedia Still image capture modes While using Still Image capture modes, such as Photo, Contacts Picture, Picture Theme, Panorama, Sports, and Burst, you can capture still image(s) by pressing the CAMERA button on the device or the ENTER button on the NAVIGATION. Still images will be saved in JPEG format. While capturing an image in the Picture Theme capture mode, you can select a preset template. To view and select from different templates, tap on the Camera screen.
Experiencing Multimedia 151 The Review screen After taking a still image or recording a video clip, you can view the image or video clip on the Review screen. In addition, you can tap the icons at the bottom of the Review screen to delete a captured image or video, send it via e-mail or MMS, and more. Review screen icons 1 2 3 4 5 Photo, Video, MMS Video Picture Theme, and Panorama modes Sports and Burst modes 1 Back. Tap 2 Delete. Tap 3 Send.
Experiencing Multimedia 5 Assign to Contacts. Tap contact. to associate the photo to a selected 6 Browse. After you have taken photos in Sports or Burst mode, the total number of consecutive shots is shown in the lower right corner of the Review screen. Tap the up/down arrow ( ) or press NAVIGATION up/down to browse through the sequence of photos. To change the display duration of the Review screen 1. Tap to open the Camera Settings screen. 2. On the Camera Settings screen, tap appears. .
Experiencing Multimedia 153 Capture mode Video MMS Video Contacts Picture Picture Theme Panorama Sports Burst Note Capture size setting Zoom range CIF (352 x 288) No zooming available Large (320 x 240) No zooming available Medium (176 x 144) 1x to 2x Small (128 x 96) 1x to 2x Medium (176 x 144) 1x to 2x Small (128 x 96) 1x to 2x Large (480 x 640) No zooming available Medium (240 x 320) 1x to 2x Small (120 x 160) 1x to 4x Determined by the current template Depends on the size of
Experiencing Multimedia The Camera Settings screen While capturing a still image or video clip using any capture modes, tap the Tool ) to access the Camera Settings icon ( screen. The Camera Settings screen allows you to configure the capture settings. Camera Settings screen in Photo mode When you tap the icons at the bottom of the Camera Settings screen, different menus will appear. Some menus and options may be available only in certain capture modes.
Experiencing Multimedia 155 3 3 Tap to select a setting and close the submenu. Alternatively, press NAVIGATION up/down to select a setting, then press NAVIGATION left to close the submenu. For more information about the different menus and settings, see the succeeding sections. Self-timer menu • Self-timer. Select the Self-timer option for capturing images: Off, 2 seconds, or 10 seconds.
Experiencing Multimedia Ambience menu • White Balance. Select a white balance setting type such as Fluorescent, Night, etc. to suit your lighting environment. • Effect. Choose a special effect such as Grayscale, Sepia, etc., to apply to your photos or video clips. Capture Settings menu • Resolution. Select the desired image or video size. • Quality. Select the JPEG image quality level for all captured still images. You can choose from Basic, Normal, Fine, and Super Fine. • Metering Mode.
Experiencing Multimedia 157 • Capture Format. Select the desired file format. • Shutter Sound. Choose whether or not you want the camera to make a shutter sound when you press the ENTER button or the CAMERA button to take photos or record video clips. • Grid (Photo mode only). Choose whether or not to show a grid on the Camera screen. Showing a grid helps you frame and centre your subject more easily and accurately. Grid • Keep Backlight.
Experiencing Multimedia “IMAGE” or “VIDEO” followed by a sequential number, for example: IMAGE_001.jpg. You may also choose to name files using either the current Date or Date & Time as the prefix. • Counter. By default, the newly captured image or video files are named with a prefix and some sequential numbers, such as 001, 002, and so on. To reset the numbering to “001” for your captured files, tap Reset. • Recording Limit. Specify the maximum time or file size for recording.
Experiencing Multimedia 159 8.2 Using Pictures & Videos The Pictures & Videos programme collects, organises, and sorts images and video clips in the following formats on your device. File Type File Extensions Image *.bmp, *.jpg, *.gif GIF animation *.gif Video *.avi, *.wmv, *.mp4, *.3gp You can view the pictures as a slide show, beam them, send them via e-mail, edit them, or set them as the background on the Today screen.
Experiencing Multimedia The down arrow GIF animation icon Tap to view the selected image. To play videos with audio 1. Tap Start > Programs > Pictures & Videos. By default, the contents of the My Pictures folder will be shown. 2. To find the video clips that you captured, tap the down arrow ( ) next to the My Pictures folder and tap My Documents > My Videos. Video clips are displayed as thumbnails by default, which appear with ). a media icon ( The media icon 3.
Experiencing Multimedia 161 To view slide shows You can view your pictures as a slide show on your device. Pictures are shown in full-screen view with 5-second intervals between slides. 1. Tap Start > Programs > Pictures & Videos. 2. Tap Menu > Play Slide Show. Note You can specify how pictures are scaled to optimise their display in a slide show. Tap Menu > Options, then tap Portrait pictures or Landscape pictures on the Slide Show tab.
Experiencing Multimedia • • Note To crop a picture, tap Menu > Crop. Next, tap and drag to select the area to crop. Tap inside the box to crop, or tap outside the box to cancel cropping. To adjust the brightness and contrast levels of a picture, tap Menu > Auto Correct. To undo an edit, tap Menu > Undo. To cancel all unsaved edits you made to the picture, tap Revert to Saved. To set a picture as the Today screen background You can use a picture as the background on the Today screen. 1.
Experiencing Multimedia 163 3. Tap Menu > Beam. 4. Select a device to beam the file to. 5. Tap OK. To assign pictures to contacts You can assign a picture to a contact so that you can easily identify the contact at any point of time. 1. Tap Start > Programs > Pictures & Videos. 2. Select the picture you want to assign to a contact. 3. Tap Menu > Save to Contact. 4. Tap the contact, or navigate and tap Select to choose the contact from your Contacts list. To customise more image settings 1.
Experiencing Multimedia 8.3 Using Windows Media Player Mobile You can use Windows Media Player Mobile to play digital audio and video files that are stored on your device or on a network, such as on a Web site. The following file formats are supported by Windows Media Player Mobile. Video File Formats Supported • • • • • Windows Media Video MPEG4 Simple Profile H.
Experiencing Multimedia 165 This control Does this Play/Pause a file. Display the video in full screen. Display a Web site where you can find music and videos to play. Adjust the playback progress of a selected file. Skip to the beginning of the current file or to the previous file. Skip to the next file. Decrease the volume level. Increase the volume level. Turn the sound on or off. About the screens and menus Windows Media Player Mobile has three primary screens: • Playback screen.
Experiencing Multimedia About licences and protected files Some media files have associated licences that protect them from being unlawfully distributed or shared. If you want to copy a protected file from your PC to your device, use the Windows Media Player on your PC to synchronise the file to your device. This will ensure that the licence is copied along with the protected file. For more information about synchronising files to your device and other mobile devices, see the Windows Media Player Help.
Experiencing Multimedia 167 2. Click the Sync tab on the Windows Media Player of your PC. Select a Playlist or a Library on the left panel of the Windows Media Player. 3. From the Content List, drag the media files that you want to sync to your device and drop them to the Sync List. Playlists and Library List Content List Sync List 4. Click Start Sync to start synchronising the selected files to your device.
Experiencing Multimedia 2. On the Library screen, tap the Library arrow (near the top of the screen), then tap the media storage that you want use, for example, Storage Card. 3. In most cases, Windows Media Player Mobile automatically updates the library. However, you can manually update the library to ensure that it contains new files that you recently copied to your device or storage card. Tap Menu > Update Library to manually update the library list. 4.
Experiencing Multimedia 169 about synchronising media, see “Synchronise video and audio files” earlier in this chapter. In Windows Media Player Mobile on your device, your playlists are available in the Library under the My Playlists category. There is also a temporary playlist, called Now Playing, which lists the currently playing file, as well as any files that have been queued up to play next.
Experiencing Multimedia 8.4 Using Audio Manager Audio Manager is a music browser and player in one. It gives you access to all the music files on your device, and allows you to easily browse for the music that you want to play by organising music into categories such as title, artist, album, etc. You can also create playlists of your favourite songs and use the integrated Music Player to play them back. To launch Audio Manager • Tap Start > Programs > Audio Manager.
Experiencing Multimedia 171 No. Description 1 Opens the All Songs submenu where you can browse music files by file name or song title. 2 Opens the Playlists submenu where you can create playlists and play them back. 3 Opens a submenu where you can browse music files by the selected category. 4 Switches to the Music Player screen. (Music Player does not automatically start playback. You need to tap the icon). 5 Shows the current submenu name. Tap to return to the upper-level menu.
Experiencing Multimedia Music Player Music Player is integrated within Audio Manager, and it lets you play back music files. After selecting a song in the Library, Music Player opens and automatically plays it. Use the available buttons to control the playback. Note No. 1 2 3 4 5 7 8 6 10 9 If the last screen you were in was the Music Player when you closed Audio Manager, next time you launch Audio Manager, it will open Music Player directly. To switch back to the Library, tap Library.
Experiencing Multimedia 173 Playlists A playlist is a list of music files that play in a sequential order. The Playlists screen shows the current playlists that are found on your device and memory card. There are two types of playlists that will be shown on the Playlists screen: • Windows Media Player playlists.
Experiencing Multimedia 2. On the Playlists screen, tap Menu > New. 3. Enter a Playlist name and tap OK. 4. On the Playlists screen, tap the playlist you have just created and tap Edit. 5. Tap Menu > Add. 6. Tap the check boxes to select the songs you want to add to the playlist, then tap OK. Tap Menu to open a list of selection methods. 7. Tap OK twice. To play a playlist 1. On the Playlists screen, tap to select a playlist. 2. Tap the first song in the selected playlist.
Experiencing Multimedia 175 Set music as ring tone Audio Manager allows you to select your favourite music and set it as a ring tone for your device. 1. Use the NAVIGATION Control to select a song in the Library, or tap a song to play it in Music Player. 2. Tap Menu > Set as Ring Tone. 3. If the selected song is in MP3 format, you can trim it first to make it shorter. Tap Trim to open the MP3 Trimmer and trim the song. For more information about trimming, see “MP3 Trimmer”. 4. Tap Set as Default Ring Tone.
Experiencing Multimedia No. Description 1 Title. Shows the ring tone name for the song. 2 Duration. Shows the length of the song after trimming. 3 Time. Shows the playback time when the song is played. 4 Trimmer. Allows you to mark the part of the song that will be used for the ring tone. Drag the left handle to mark the start time (mark-in point), then drag the right handle to mark the end time (mark-out point). 5 Play/Stop. Tap to toggle between playing and stopping playback.
Chapter 9 Using Other Applications 9.1 Word Mobile 9.2 Excel Mobile 9.3 Viewing Slide Shows with PowerPoint Mobile 9.4 Using Adobe Reader LE 9.5 Using MIDlet Manager 9.6 Using ZIP 9.
Using Other Applications 9.1 Word Mobile Word Mobile is a streamlined version of Microsoft Word. Word documents created on your PC can be opened and edited on your device. You can also create and edit documents and templates in Word Mobile and save them as *.doc, *.rtf, *.txt, and *.dot files. You can have only one document open at a time. When you open a second document, the first one is saved and closed automatically. To create a Word file 1. In Word Mobile, tap New.
Using Other Applications 179 9.2 Excel Mobile Excel Mobile makes it easy for you to open and edit Excel workbooks and templates created on your PC. You can also create new workbooks and templates on your device. To create an Excel file 1. In Excel Mobile, tap New. You’ll see either a blank worksheet or template, depending on what you’ve selected as the default template. 2. Tap a cell to select it. Using the on-screen keyboard, enter your data then tap the Enter key. 3.
Using Other Applications 9.3 Viewing Slide Shows with PowerPoint Mobile With PowerPoint Mobile, you can open and view slide show presentations created on your PC. Slide shows in *.ppt and *.pps format created using PowerPoint '97 and later can be viewed in PowerPoint Mobile. Many presentation elements built into the slide shows such as slide transitions and animations will play back on the device. If the presentation is set up as a timed slide show, one slide will advance to the next automatically.
Using Other Applications 181 9.4 Using Adobe Reader LE Adobe Reader LE is an application for viewing PDF (Portable Document Format) documents on your device. It supports a subset of the features found in the PC versions of Adobe Reader. To open a PDF file on your device Do one of the following: • Tap Start > Programs > Adobe Reader LE. Browse the folders on your device or storage card and find the desired PDF file. Tap the file to open it.
Using Other Applications Tips Alternatively, you can also tap the following toolbar buttons at the bottom of the screen: • Tap to Fit Screen; tap to Fit Width. • Tap to zoom in; tap to zoom out. To rotate the view • Tap Tools > View > Rotate Right to rotate the document view clockwise in 90 degree increments. • Tap Tools > View > Rotate Left to rotate the document view counterclockwise in 90 degree increments.
Using Other Applications 183 9.5 Using MIDlet Manager MIDlets are Java applications that can run on mobile devices. Your device supports Java 2 Micro Edition, J2ME. The MIDlet Manager allows you to download Java applications, such as games and tools that are specifically designed for mobile devices. Although some Java applications and games have already been installed on your device, the Java MIDlet Manager gives you the flexibility of installing and managing additional J2ME applications from the Internet.
Using Other Applications To run MIDlets on your device 1. Tap Start > Programs > MIDlet Manager. 2. Tap a MIDlet to run. To view the MIDlets currently running • Tap the down arrow on the top left of the MIDlet Manager screen, then tap Running. Note To view the most recently used MIDlets, tap Show > Recent. To stop running a MIDlet 1. Tap the down arrow on the top left of the MIDlet Manager screen, then tap Running. 2. Tap and hold a MIDlet on the Running MIDlets screen, and tap Stop.
Using Other Applications 185 To change the display name of a MIDlet 1. Tap and hold a MIDlet, and tap Rename. 2. Enter a new name for the MIDlet, then tap OK. Note You cannot change the name of a MIDlet suite. To uninstall a MIDlet/MIDlet suite Before you uninstall a MIDlet/MIDlet suite, make sure that it is not running. 1. Tap and hold the MIDlet/MIDlet suite, and tap Uninstall. 2. Tap OK to confirm.
Using Other Applications Security Option Description Net Access Determine whether a MIDlet/MIDlet suite can access the Internet. Local Connectivity Enable a MIDlet/MIDlet suite to access services, such as infrared and Bluetooth. App Auto Run Enable a MIDlet/MIDlet suite to run at specified times, or any time. Messaging Determine whether a MIDlet/MIDlet suite can send and/or receive SMS messages. Multimedia Recording Note Enable a MIDlet/MIDlet suite to record sounds and images.
Using Other Applications 187 Note You cannot select multiple ZIP files. 2. The files contained in the zip file are then displayed. Select files by doing one of the following: • Tap to select a file. • To select several files, tap Action and make sure Multi-Select Mode is selected. Select files by tapping each file. (Tap a selected file to deselect it). • To select all files, tap Action > Select All. 3. Tap Action > Extract. 4. Choose a folder in which files will be extracted to, then tap Extract.
Using Other Applications 9.7 Using Voice Speed Dial You can record voice tags so that you can dial a phone number or launch programmes simply by speaking a word. Create a voice tag for a phone number 1. Tap Start > Contacts to open the Contacts list. 2. Do one of the following: • Tap and hold the desired contact, then tap Add Voice Tag. • Select the desired contact, then tap Menu > Add Voice Tag. • Tap the desired contact to open the contact’s detailed screen, then tap Menu > Add Voice Tag. 3.
Using Other Applications 189 5. When you create a voice tag for the item, you can do one of the following: • Tap the Record button ( ) to rebuild the voice tag. • Tap the Play button ( ) to play the voice tag. • Tap the Delete button ( ) to delete the voice tag. Tip To ensure voice recognition accuracy, please record your voice in a quiet place. Create a voice tag for a programme 1. Tap Start > Settings > Personal tab > Voice Speed Dial. 2.
Using Other Applications
Appendix A.1 Regulatory Notices A.2 PC Requirement to Run ActiveSync 4.x A.
Appendix A.1 Regulatory Notices Regulatory Agency identifications For regulatory identification purposes, your product is assigned a model number of PAND100. To ensure continued reliable and safe operation of your device, use only the accessories listed below with your PAND100. The Battery Pack has been assigned a model number of TRIN160. This product is intended for use with a certified Class 2, rated 5 Volts DC, maximum 1 Amp power supply unit.
Appendix 193 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) for radio equipment and services; Part 7: Specific conditions for mobile and portable radio and ancillary equipment of digital cellular radio telecommunications systems (GSM and DCS). • ETSI EN 301 489-17 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2.
Appendix Safety precautions for RF exposure • Use only original manufacturer-approved accessories, or accessories that do not contain any metal. • Use of non-original manufacturer-approved accessories may violate your local RF exposure guidelines and should be avoided. Exposure to radio frequency (RF) signals Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy.
Appendix 195 Telecommunications & Internet Association (TIA) safety information Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of six inches be maintained between a handheld wireless phone and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research.
Appendix WEEE Notice The Directive on Waste Electrical and Electronic Equipment (WEEE), which entered into force as European law on 13th February 2003, resulted in a major change in the treatment of electrical equipment at end-of-life. The purpose of this Directive is, as a first priority, the prevention of WEEE, and in addition, to promote the reuse, recycling and other forms of recovery of such wastes so as to reduce disposal.
Appendix 197 A.2 PC Requirement to Run ActiveSync 4.x To connect your device to the PC, you must have Microsoft® ActiveSync® programme installed on your PC. ActiveSync 4.
Appendix A.3 Specifications System Information Processor Samsung® SC32442A, 400 MHz Memory - ROM : 256 MB - RAM : 128 MB SDRAM (Figures are the total ROM and RAM memory available for use and storage. Since the memory is shared by the Operating System, applications, and data, the actual available memory is less than what is written). Operating System Windows Mobile® Version 5.0 Pocket PC Phone Edition Power Battery Rechargeable Lithium-ion polymer battery, 1500 mAh Charging Time Up to 3.
Appendix 199 Camera Module Type 2.0 Megapixel colour CMOS camera Resolution Photo: 1600x1200 (UXGA), 1280x960 (SXGA), 640x480 (VGA), 320x240 (QVGA), 160x120 (QQVGA) Video: 176x144 (QCIF), 128x96 Digital Zoom Up to 8X Connections Infrared IrDA SIR I/O Port HTC ExtUSBTM : an 11-pin mini-USB and audio jack in one (ExtUSB is a proprietary connection interface that is trademarked by HTC). Car Antenna Connector Yes Wireless Connections Bluetooth 2.0, Wi-Fi (IEEE 802.
Appendix Audio Audio Controller AGC Microphone/ Speaker Built-in/Dual, Hands-free Headphone AMR/AAC/WAV/WMA/MP3 codec Expansion Slots Card Slot SDTM Card
Index
Index A B A2DP 95 About licences and protected media 166 ActiveSync 58 - Comm Manager 92 - copy files 76 - overview 28 - synchronise 59 Add and remove programmes 73 Add attachment to message 120 Adobe Reader LE 181 - adjust display size 181 - change page layout 182 - exit 182 - navigate through document 181 - rotate the view 182 - search for text in the document 182 Alarm 68 Answer/end a call 47 Appointment search 40 Assign pictures to contacts 163 Assign programmes or shortcuts to hardware buttons 69
Index 203 Camera - capture modes 146, 147 - controls 147 - file formats 147 - icons 147 - overview 29 - settings 154 - specifications 199 Change - device name 68 - screen text size 70 Clock & Alarms 32, 68 Close programme 76 Comm Manager 33, 92 Compose messages 119 Conference call 50 Connect device to Internet - set up dial-up connection to ISP 88 - set up GPRS connection 86 - start a connection 88 Connect to private network 88 Contacts 29, 134 Contacts Picture capture mode 147 Contacts search 40 Cookies 91 C
Index F Favourites (Internet Explorer) 89 File Explorer 29 Find - device information 70 - operating system version number 70 Find contact - online 137 - on device 136 Forward message 120 G Games 29 GIF animation 159 GPRS 86 GPRS Monitor 30, 107 H Hard reset 84 Help 29 Help search 40 Home page (Internet Explorer) 89 I IMAP4 117 Infrared (IR) - beam picture or video 162 - synchronise 63 Input methods - Block Recognizer 38 - Keyboard 37 - Letter Recognizer 37 - Transcriber 38 Input Panel 36 Install -
Index 205 Microsoft Windows Mobile Device Centre 55 MIDlet Manager - configure MIDlet security 185 - install MIDlets from Internet 183 - install MIDlets from PC 183 - manage MIDlets/MIDlet suites 184 - overview 29, 183 - uninstall MIDlets/MIDlet suites 185 MMS 126 - add audio clip 130 - add emoticon 130 - add photo/video 128 - add text 130 - add Web page address from Favourites 130 - create and send 128 - MMS settings 126 - reply message 131 - view message 131 MMS Video capture mode 147, 150 MP3Trimmer 29 MS
Index - Camera 29, 146 - Comm Manager 33, 92 - Contacts 29, 134 - Download Agent 29 - Excel Mobile 29, 179 - File Explorer 29 - Games 29 - GPRS Monitor 30 - Help 29 - Internet Explorer Mobile 29, 89 - Internet Sharing 29, 106 - Messaging 29, 116 - MIDlet Manager 29, 183 - MP3Trimmer 29 - Notes 29, 140 - Phone 29, 44 - Pictures & Videos 30, 159 - Pocket MSN 30, 131 - PowerPoint Mobile 30, 180 - SAPSettings 30 - Search 30, 40 - SIM Manager 30, 46, 134 - Spb GPRS Monitor 107 - Sprite Backup 30, 78 - STK (S
Index 207 Settings (Personal tab) - Buttons 31 - Input 31 - Lock 31 - Menus 31 - MSN Options 31 - Owner Information 31 - Phone 32 - Sounds & Notifications 32 - Today 32 - Voice Speed Dial 32 Settings (System tab) - About 32 - Backlight 32 - Certificates 32 - Clear Storage 32 - Clock & Alarms 32 - Device Information 32 - Error Reporting 32 - Key Lock 32 - Memory 33 - Microphone AGC 33 - Power 33 - Regional Settings 33 - Remove Programmes 33 - Screen 33 - Task Manager 33 Set picture as Today screen background 1
T Tasks 30, 138 Tasks search 40 Task Manager 71 Temporary Internet files (Internet Explorer) - delete 91 Terminal Services Client 112 Text size - screen 70 - Web pages 90 Time 68 Today screen 25, 66 Transcriber 38 Troubleshoot Windows Media Player Mobile 169 Turn device on and off 23 Turn phone function on and off 43, 92 U USB modem 106 USB to PC 60 V Verify digital signature 124 Vibrate 43, 92 Video capture mode 150 View - MMS 131 - photo slideshows 161 - pictures 159 Voice call 44 Voice note 142 Voice R
