User MANUAL OAKWORKS 100 Series Procedure Chair ® Model 121A Model 100 www.oakworks.com · 717.235.
© Copyright 2012 OAKWORKS® , Inc. Notice The information contained in this document is subject to change without notice and should not be construed as a commitment by OAKWORKS®, Inc. Printed in USA All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent of OAKWORKS®, Inc. OAKWORKS® is a registered trademark of OAKWORKS®, Inc. OAKWORKS®, Inc.
Table of Contents Product Use Description ..................................................................................................... 1 Important Safety Instructions Symbol Identification..................................................................................................... 1 Safety Instructions ......................................................................................................1-2 Product Description & Photo 100 Series Procedure Chair .............................
Product use description / important safety instructions product use description The Procedure Chair is a powered positioning examination chair and table used to support the patient during medical procedures. It is intended to be operated by a healthcare professional in a medical environment. No special training is required but a review of the following Safety Instructions is important for the safety of the operator and patient.
Important Safety instructions The chair should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary, the chair should be observed to verify normal operation in the configuration in which it will be used. The chair is designed to be a stand alone chair. This chair must not be modified or incorporated into any other equipment. As with any moving mechanism there are potential pinch points around and underneath the chair.
product description 100 Series Procedure Chair Adjustable Head Rest Arm rest shown in up position Paper Roll Holder (1) Arm Rests (2) (optional) electric adjustment 0° to 80° Electric Fowler Arm rest shown in down position Retractable Stirrups (2) (optional) Electric Lift Towers (2) Manual Adjustable Four Position Leg Rest Aesthetic Model Thermaformed Base Foot Control Aesthetic Model Thermaformed Extended Sub-top Standard Specifications Motion 1 Powered 19” - 35” (48.3-88.9 cm.
installation The Procedure Chair come completely assembled and ready to use. Plug the cord into a functioning outlet that is rated for the chair. (see Grounding below) Arrange the power cord and control cords so that they will not create a tripping hazard and where the controls are located to your liking and are conveniently accessible. Be sure access to plug is not blocked for disconnecting the chair from power.
directions for use Foot control operations caution Do not sit on the Fowler (Backrest) or Leg Rest sections. Do not leave the patient unattended. When lowering the chair or using the Trendelenburg functions, make sure there is nothing that can impede motion (like stools, cabinets, accessory parts, cleaners, etc.) The Multi-function Foot Control and optional Hand Control operate all functions of the chair with the touch of a button. Follow the directions below to access these functions.
directions for use arm rest use To lower the arm rests To raise the arm rests Push arm rest in lightly towards the center of the table, then pull locking knob down towards the table base. Fold arm rests down and under the table. Grasp arm rest and rotate to the raised position. When fully up, the arm rest will lock into position. Check that the arm rest is locked by applying light outward pressure. retractable foot rests (stirrup) use caution 1.
directions for use adjustable head rest use caution Do not extend dowels more than 4” (10.2 cm.) from the back rest section. The head rest angle is adjusted using a single cam locking handle. The head rest distance from the table is adjusted by using a knob. To adjust the position of the head rest follow these steps: to adjust head rest angle Turn knob counter-clockwise to unlock the cam. Move head rest platform to the desired position. Turn knob clockwise to lock the cam.
directions for use manual adjustable four position leg rest use caution Do not sit on the Fowler (Backrest) or Leg Rest. (Max Capacity 150 lbs. (68 kg.)) To raise the leg Rest To lower the leg Rest Raise the leg rest by pulling it up from the lower center end of the table to the proper position for the procedure. Use a slow or medium speed. If you raise the leg rest too fast, the height locking mechanism will not engage. The leg rest will lock into the closest height position.
cleaning & disinfection / inspections / warranty cleaning & disinfection warning Before cleaning with any liquid cleaner be sure to unplug the power cord from the outlet. Use a 10% sodium hypochlorite (bleach) solution or Recommended Disinfectants on all surfaces. Clean all sides of each upholstered section. Follow the directions on the disinfectant and wipe off excess.
model number & serial number model & serial numbers The model number and serial number are located on the lift column at the foot end of the table. Procedure Tables and Chairs Model Number 3034177 Serial Number 16796025 PCEXG327197425TTZZF6BK Ser#: PC1565022 PCG 100A Series 27 x 19-35 x 74 25/TT/XXF6BK TTSKYBLUE 01/04/2013 Order#:654321 Notes: Sample Product Label Power Rating: US 120 V 60 Hz 5.
specifications product specifications North America Europe Weight 273 lbs. 124 kg. Shipping Weight 409 lbs. 186 kg. Lifting Capacity 550 lbs. 250 kg.
specifications Guidance and manufacturer’s declaration - electromagnetic emissions The chair is intended for use in the electromagnetic environment specified below. The customer or the user of the chair should assure that it is used in such an environment.
specifications Guidance and manufacturer’s declaration - electromagnetic immunity The chair is intended for use in the electromagnetic environment specified below. The customer or the user of the chair should assure that it is used in such an environment.
specifications Guidance and manufacturer’s declaration - electromagnetic immunity The chair is intended for use in the electromagnetic environment specified below. The customer or the user of the chair should assure that it is used in such an environment.
this page is intentionally left blank 15
this page is intentionally left blank 16
User MANUAL OAKWORKS 100 Series Procedure Chair ® Contact Information: Oakworks® Inc. 923 East Wellspring Road New Freedom, PA 17349 Phone: 717-235-6807 FAX: 717-235-6798 www.oakworksmed.com 3034177 CONFORMS TO: ANSI/AAMI STD ES60601-1 IEC STD 60601-1 3rd Edition IEC STD 60601-1-2 3rd Edition IEC STD 60601-1-6 3rd Edition Certified to CAN/CSA STD C22.2 No.