User MANUAL OAKWORKS 300 Series Procedure Chair ® made in the USA with US & imported parts www.oakworksmed.com · 717.235.
© Copyright 2013 OAKWORKS® , Inc. Notice This manual was originally drafted and approved in the English language. Printed in USA All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent of OAKWORKS®, Inc. OAKWORKS® is a registered trademark of OAKWORKS®, Inc. The information contained in this document is subject to change without notice and should not be construed as a commitment by OAKWORKS®, Inc. OAKWORKS®, Inc.
Table of Contents Product Use Description ..................................................................................................... 1 Important Safety Instructions Symbol Identification..................................................................................................... 1 Safety Instructions ......................................................................................................1-2 Product Description & Photo 300 Series Procedure Chair .............................
Product use description / important safety instructions product use description The Procedure Chair is a powered positioning examination table used to support the patient during medical procedures. It is intended to be operated by a healthcare professional in a medical environment. No special training is required but a review of the following Safety Instructions is important for the safety of the operator and patient.
Important Safety instructions The arm rests are not designed to be used as patient restraints. Use appropriate patient restraints. The chair should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary, the chair should be observed to verify normal operation in the configuration in which it will be used. The chair is designed to be a stand alone chair. This chair must not be modified or incorporated into any other equipment.
Product Description 300 Series Procedure Chair Adjustable Head Rest (accessory) 12 Button Hand Control Paper Roll Holder (1) Self-Adjusting Removable Arm Rests (2) (accessory) Retractable Foot Rests (Stirrups) (2) (option) Fixed T-Rail (2) (option) Rotate up to 240 º electric adjustment 0° to 80° Electric Back Rest electric adjustment 0° to 90° Swivel Base (option) Electric Leg Rest Electric Lift Towers (2) Standard Specifications Motion 1 Powered 19”-35” (48-89 cm.
installation The Procedure Chairs come completely assembled and ready to use. Plug the cord into a functioning outlet that is rated for the table. (see Grounding below) Arrange the power cord and control cords so that they will not create a tripping hazard and where the controls are located to your liking and are conveniently accessible. Be sure access to plug is not blocked for disconnecting the table from power.
directions for use hand control operations caution Do not sit on the Fowler (Backrest) or Leg Rest sections. Do not leave the patient unattended. When lowering the chair or using the Trendelenburg functions, make sure there is nothing that can impede motion (like stools, cabinets, accessory parts, cleaners, etc.) The Multi-function Hand Control operates all functions by holding down one button at a time. Follow the directions below to access these functions.
directions for use foot control operations caution Do not sit on the Fowler (Backrest) or Leg Rest sections. Do not leave the patient unattended. When lowering the chair or using the Trendelenburg functions, make sure there is nothing that can impede motion (like stools, cabinets, accessory parts, cleaners, etc.) The Multi-function Foot Control operates all functions by holding down one button at a time. Follow the directions below to access these functions.
directions for use sWIVEL bASE uSE caution When rotating the chair, make sure there is nothing around the chair that can impede the rotational motion (like stools, cabinets, etc) Rotate up to 240 º The chair can be rotated with a patient in it. Locate the black push buttons at the top of the back rest section. Press in and hold either one of the buttons to disengage the base locking mechanism. While holding in the push button, rotate the chair to the desired position up to 240°.
directions for use Head Rest uSE caution Do not extend the dowels more than 4” (10 cm.) from the Back Rest section. Adjustable Large The Adjustable head rest angle is adjusted using a locking knob. The head rest distance from the table is adjusted by using a knob. The Large head rest is adjusted by using the knob. To adjust the position of the head rest, follow these steps: hEAD rEST aNGLE (Adjustable Head Rest only) Turn knob counter-clockwise to unlock the cam.
directions for use procedure tray use caution Make sure the Leg Rest is fully lowered before using the procedure tray. Do not sit or push on the Procedure Tray when extended from the seat. Maximum Weight rating of 15 lbs. (6.8 kg.) Do not use the Procedure Tray when using the Trendelenburg function. The Chair seat must remain flat while using the Procedure Tray. Slide out the Procedure Tray by pulling on the center slot of the tray holder until the tray stops.
directions for use Arm Rest Installation and Adjustment caution Do not use the arm rest for patient support during the mounting or dismounting of the chair. The arm rest is not designed to support the patient’s weight. to install the arm rests: The Arm Rests adjust automatically as the back rest moves to remain parallel to the floor. 1. Insert end of arm rest into backrest hole while holding the arm rest at a 60° angle to the backrest. 2.
directions for use Procedure Chair Face Rest Crescent The Procedure Chair Face Rest Crescent is designed to be used for prone positioning. An Adjustable Head Rest is required for this accessory. T-Rail Adapter The T-Rail Adapter can be attached at designated locations on one or both sides of the back rest section, allowing the use of any t-rail accessory. Attach or remove using knobs. The T-Rail Adapter has a Maximum Load Capacity of 150 lbs. (68 kg.
cleaning & disinfection / inspections / warranty cleaning & disinfection warning Before cleaning with any liquid cleaner be sure to unplug the power cord from the outlet. Use a 10% sodium hypochlorite (bleach) solution or Recommended Disinfectants on all surfaces. Clean all sides of each upholstered section. Follow the directions on the disinfectant and wipe off excess.
model number & serial number model & serial numbers The model number and serial number are located on the seat acrylic on the backside of the chair. Procedure Tables and Chairs Model Number 3034177 16796025 PC30G32719743MTTZZH8BK Ser#: PC1565022 PCM 300 Series 27 x 19-35 x 74 3M/TT/XXH8BK TTSKYBLUE 01/04/2013 Order#:654321 Notes: Sample Product Label Serial Number Power Rating: US 120 V 60 Hz 5.8 A Duty Cycle: MAX 2 minutes ON/18 minutes OFF Class 1 Equipment 923 East Wellspring Rd.
specifications product specifications Weight 280-325 lbs. (127-148 kg.) Shipping Weight 372-417 lbs. (169-189 kg.) Lifting Capacity 550 lbs. (250 kg.
specifications Guidance and manufacturer’s declaration - electromagnetic emissions The chair is intended for use in the electromagnetic environment specified below. The customer or the user of the chair should assure that it is used in such an environment.
specifications Guidance and manufacturer’s declaration - electromagnetic immunity The chair is intended for use in the electromagnetic environment specified below. The customer or the user of the chair should assure that it is used in such an environment.
specifications Guidance and manufacturer’s declaration - electromagnetic immunity The chair is intended for use in the electromagnetic environment specified below. The customer or the user of the chair should assure that it is used in such an environment.
this page is intentionally left blank 18
this page is intentionally left blank 19
Revision History Revision History Revision Date A B C 08/08/2013 08/21/2013 01/27/2014 Description Word - New Document Updated to Indesign Format; Updated specification section Added caution note to Procedure Tray section; Updated Model Number Description Section 20
User MANUAL OAKWORKS 300 Series Procedure Chair ® Contact Information: Oakworks® Inc. 923 East Wellspring Road New Freedom, PA 17349 Phone: 717-235-6807 FAX: 717-235-6798 www.oakworksmed.com 3034177 CONFORMS TO: ANSI/AAMI STD ES60601-1 IEC STD 60601-1 3rd Edition IEC STD 60601-1-2 3rd Edition IEC STD 60601-1-6 3rd Edition Certified to CAN/CSA STD C22.2 No.
