USER MANUAL OAKWORKS EC Procedure Chair ® made in the USA with US & imported parts www.oakworksmed.com · 717.235.
© Copyright 2014 Oakworks® , Inc. Notice The information contained in this document is subject to change without notice and should not be construed as a commitment by Oakworks®, Inc. Printed in U.S.A. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent of Oakworks®, Inc. Oakworks® is a registered trademark of Oakworks®, Inc. Oakworks®, Inc.
TABLE OF CONTENTS Product Use Description ........................................................................................... 1 Important Safety Instructions Symbol Identification............................................................................................ 1 Safety Instructions ........................................................................................... 1-2 Product Description & Photo EC Procedure Chair....................................................................
PRODUCT USE DESCRIPTION / IMPORTANT SAFETY INSTRUCTIONS PRODUCT USE DESCRIPTION The Oakworks EC Procedure Chair is used to support the patient during examinations and procedures. It is intended to be operated by a healthcare professional in a medical environment. No special training is required but a review of the following Safety Instructions is important for the safety of the operator and patient. The healthcare professional should read and understand this entire manual before use with a patient.
IMPORTANT SAFETY INSTRUCTIONS Weight Limit: (patient and accessories) 550 lbs. (250 kg) Do not exceed. • The Back Rest and Leg Rest sections are not designed to support the entire weight of the patient. Do not sit on the Back Rest or Leg rest sections. • Be certain that the chair is completely lowered prior to discharging an ambulatory patient. The patient may lose balance and fall. • This chair is not suitable for use in the presence of flammable anesthetic mixture with air or oxygen or nitrous oxide.
PRODUCT DESCRIPTION EC Procedure Chair Optional Side Rails Manual Lift-Assist Back Rest Optional Stirrups Steel Scissor-style powder-coated base with dual crossbeams (1) Single 24v motor with cover Wheels (2) Articulating Foot/Leg Rest Section STANDARD SPECIFICATIONS OPTIONS 3 Section Top 29” (74cm) wide x 73” (185cm) long Stirrups Back rest 29” (74cm) wide x 39” (99cm) long Side Rails Seat 29” (74cm) wide x 23” (58cm) long Arm Rest Leg rest 29” (74cm) wide x 10” (25cm) long Locking Twin C
INSTALLATION The Chairs come completely assembled and ready to use. Plug the cord into a functioning outlet that is rated for the chair. (see Grounding below) Arrange the power cord and control cords so that they will not create a tripping hazard and where the controls are located to your liking and are conveniently accessible. Be sure access to plug is not blocked for disconnecting the chair from power. GROUNDING DANGER Risk of Electric Shock - Connect this furnishing to a properly grounded outlet only.
DIRECTIONS FOR USE CONTROL OPERATIONS CAUTION Be sure the self-locking rubber feet are flat side down to ensure safety and stability. The chair offer height positioning with electronic ease. Operate the Foot control or optional hand control as shown below to raise or lower the height of the chair.
DIRECTIONS FOR USE ARTICULATING LEG REST USE CAUTION Do not sit or stand on the articulating leg rest section. Do not use leg rest section in assisting the patient on or off the chair. Grasp Firmly & Lift Release Knob TO RAISE THE LEG REST TO LOWER THE LEG REST: Grasp the edge of the section and lift up until you have achieved the angle needed. Release and it will lock into place automatically. Twist and hold the knob under the leg rest and push leg rest down.
DIRECTIONS FOR USE MOVING THE CHAIR CAUTION Before moving the Chair, disconnect the power cord from the power outlet. The chair weighs as much as 200 lbs. (91 kg.) Use caution when lifting the chair to move it. Two people are required to move the chair safely. DO NOT use the chair to transport a patient. The chairs are equipped with two wheels at one end and two self-locking feet at the other. When ready to move the chair, first lower the chair to its lowest position.
DIRECTIONS FOR USE RETRACTABLE FOOT RESTS (STIRRUP) USE CAUTION Pinch Point - Keep fingers away from pinch point. 1. Fully rase the leg rest. 4. Fold out to fully open position. 2. Grasp Stirrup handle & pull out firmly while lifting slightly. 5. Place feet in stirrups. 7. Rotate stirrup to the desired angle. 6. Lower leg rest. 3. Rotate outward. 8. To reduce stirrup length, lift the handle slightly and push into desired position. Stirrup will automatically lock into nearest detent position.
CLEANING & DISINFECTION / INSPECTIONS / WARRANTY CLEANING & DISINFECTION WARNING Before cleaning with any liquid cleaner be sure to unplug the power cord from the outlet. Use a 10% sodium hypochlorite (bleach) solution or Recommended Disinfectants on all surfaces. Clean all sides of each upholstered section. Follow the directions on the disinfectant and wipe off excess.
MODEL NUMBER & SERIAL NUMBER EC PROCEDURE CHAIR Model Number Serial Number PX, PT, EC & ProLuxe Series Tables and Chairs Model Numbers and Serial Numbers always start with a letter. 16796025 PXSLA3311873ACTTVN Ser#: PXR563146 US G2 30 x 22-38 x 72 3M/TT/2S TTSKYBLUE 01/04/2013 Order#:654321 Notes: Sample Product Label 2.0 A The model number and serial number are located on the underside of the foot section. Part No. CN70537-9 Rev.
SPECIFICATIONS PRODUCT SPECIFICATIONS Chair Weight: Shipping Weight: Lifting Capacity 165 lbs. (75 kg.) 245 lbs. (111 kg.) 550 lbs. (250 kg.
SPECIFICATIONS Guidance and manufacturer’s declaration - electromagnetic emissions The chair is intended for use in the electromagnetic environment specified below. The customer or the user of the chair should assure that it is used in such an environment. Emissions Test Compliance Electromagnetic environment - guidance RF emissions CISPR 11 Group 1 The chair uses RF energy only for its internal function.
SPECIFICATIONS Guidance and manufacturer’s declaration - electromagnetic immunity The chair is intended for use in the electromagnetic environment specified below. The customer or the user of the chair should assure that it is used in such an environment.
SPECIFICATIONS Guidance and manufacturer’s declaration - electromagnetic immunity The chair is intended for use in the electromagnetic environment specified below. The customer or the user of the chair should assure that it is used in such an environment.
This page is intentionally blank
This page is intentionally blank
USER MANUAL OAKWORKS EC Procedure Chair ® CONTACT INFORMATION: Oakworks® Inc. 923 East Wellspring Road New Freedom, PA 17349 Phone: 717-235-6807 FAX: 717-235-6798 www.oakworksmed.com 3034177 CONFORMS TO: ANSI/AAMI STD ES60601-1 IEC STD 60601-1 3RD EDITION IEC STD 60601-1-2 3RD EDITION IEC STD 60601-1-6 3RD EDITION CERTIFIED TO CAN/CSA STD C22.2 NO.
