Installation Guide

WATER COOLER MODELS
BPA1SK, BPA1SHS, BPI1SK, BPI1SHS,
BPD1SK, BPD1SHS, BPO1SK, BPO1SHS
INSTRUCTIONS
1. INSPECTION
Inspect the carton and water cooler for evidence of rough handling and concealed damage. Damage claims should be filed with the carrier.
2. MAINTENANCE
Periodically remove dirt and lint from the black wire and tube condenser on the back of the cooler. Disconnect the power supply cord, then clean with
the small brush attachment of a vacuum cleaner. Observance of this procedure will insure adequate air circulation so operation is efficient and
economical.
3. OVERLOAD PROTECTION
The compressor motor is equipped with an automatic reset protector which will disconnect the motor from the line in case of an overload.
4. HOT TANK THERMOSTATS
ON HOT MODELS, THE HOT TANK THERMOSTATS ARE NOT DESIGNED TO OPERATE WET. AN
ELECTRICAL FAULT MAY OCCUR IF THE THERMOSTATS ARE WETTED.
a) Do not steam or wet clean in the thermostat area.
b) All minor water spills must be wiped up immediately after loading or unloading bottle onto or from the cooler.
c) Where major water spills or leaks have occurred, (internal components have gotten wet) do not operate the hot
tank until it is assured that the thermostats have had a chance to dry out (a 48 hour period is sufficient) or that the
thermostat(s) have been replaced.
5. LUBRICATION
This unit is equipped with a hermetically sealed compressor and requires no additional lubrication.
6. TO PUT WATER COOLER INTO SERVICE
a) Cold & Cook Models
1) Invert water bottle on top of cooler.
2) Draw water from faucet(s). Allow about 30 minutes for water to chill after cooler is plugged in.
b) Hot Models
1) Invert water bottle on top of cooler.
2) Open hot faucet until water flows freely.
3) Place the hot tank heater switch in the "ON" (reset) position.
CAUTION: ON MODELS WITH HOT TANK, FAILURE TO FILL HOT TANK WITH WATER BEFORE TURNING ON HOT TANK
HEATER SWITCH, CAN CAUSE PHYSICAL DAMAGE TO THE UNIT.
c) Check the available power supply against the water cooler data plate to assure correct electrical service. Plug power supply cord into
receptacle.
d) Allow cooler to operate about 30 minutes for chilled and hot water dispensing.
CAUTION: WATER FROM HOT FAUCET CAN SCALD.
e) DO NOT operate the hot tank with either of the baffle parts removed from the cold tank; water from the inverted water bottle may overflow
onto the floor. Also, electrical consumption will increase.
f) ALTERNATE FAUCETS: A safer faucet that deters accidental dispensing of water by toddlers is available. This new faucet is simple and
easy to use with one hand, yet it adds a new measure of protection to your water cooler. See your dealer for details.
7. TO DISCONTINUE USE OF WATER COOLER
a) Disconnect power supply cord.
b) Remove water bottle from cooler.
c) Open faucet(s) to drain water.
d) Hot Models: Place the hot water heater in the "OFF" position ("O" on rocker is depressed). Draw water from the hot faucet until the water is
cool. The drain tube has a black valve located on the condenser, place a container under the drain. For convenience, insert a 4” (102mm)
length of 3/8”O.D. plastic tube into the opening at the end of the black valve and turn the petcock or simply turn the valve’s petcock without
the tube in order to open the drain. Turn the drain valve to a closed position when tank is empty. Some models have a white cap that is
removed to drain the tank.
e) ALWAYS DRAIN ALL WATER WHEN FREEZING TEMPERATURES ARE ANTICIPATED AND BEFORE SHIPPING THE WATER
COOLER.
8. SANITIZING INSTRUCTIONS
If sanitizing is required, a solution can be made by adding 1/2 teaspoonful of household bleach to one (1) gallon of water or 2 ml of household bleach
to 3 L of water. DO NOT use a stronger sanitizing solution. Wash the cooling tank and baffle in the solution. Rinse immediately. DO NOT allow
sanitizing solution to remain in the cooling tank more than 5 minutes. On hot models, DO NOT allow sanitizing solution to enter hot tank; plug inlet
to hot tank. Dispense solution through cold faucet and cook faucet if so equipped. Rinse through faucet(s) with clean water. Remove plug from hot
tank water inlet. Drain hot tank and flush with clean water.
WARNING
The warranty and the Underwriters' Laboratories listing for this machine are automatically voided if this machine is altered, modified, or combined with any
other machine or device. Alteration or modification of this machine may cause serious flooding and/or hazardous electrical shock or fire.
EXCEPT AS SET FORTH HEREIN, THE MANUFACTURER MAKES NO OTHER WARRANTY, GUARANTEE OR AGREEMENT EXPRESSED,
IMPLIED OR STATUTORY, INCLUDING ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.