F.10 v.3 OPERATING MANUAL F.10 v.3 OPERATING MANUAL © 2002 Design, 2014 1 Doc. No.
F.10 v.3 OPERATING MANUAL CONTENTS NOTICES................................................................................................2 INITIAL ACTIVATION.............................................................................3 FULL LCD..............................................................................................3 FREE SET MODES..............................................................................17 SET ALARMS................................................................
F.10 v.3 OPERATING MANUAL INITIAL ACTIVATION Oceanic Watch type dive gauges are placed in a Deep Sleep mode prior to being shipped from the factory. The intent is to extend storage life of the Battery for up to 7 years, before the unit is initially placed in service. In this mode, Date and Time are updated as they normally would be. However, they are not displayed. Upon waking the F10v3 up, the correct Date and USA Pacific Time will be displayed and it will be ready to operate with full functions.
F.10 v.3 OPERATING MANUAL Welcome to Oceanic and THANK YOU for choosing the F.10 v.3 © 2002 Design, 2014 4 Doc. No.
F.10 v.3 OPERATING MANUAL GENERAL FEATURES & DISPLAYS © 2002 Design, 2014 5 Doc. No.
F.10 v.3 OPERATING MANUAL INTERACTIVE CONTROL CONSOLE The Interactive Control Console consists of four Control Buttons that allow you to select mode options and access specific information. They are also used to enter Settings, operate the Backlight, and access additional screens of information. Throughout this manual they will be referred to as the M, S, L, and A buttons.
F.10 v.3 OPERATING MANUAL backlight To turn the Backlight On, press and release the L button momentarily (< 2 seconds). The Backlight will remain On for the Duration time set (a Set U selection) unless you turn it Off during that time. • The Backlight will come On (even if set OFF) when Alarms strike and remain On until turned Off or automatically after 10 seconds . • Pressing and releasing the L button (< 2 seconds) while the Backlight is On will turn it Off.
F.10 v.3 OPERATING MANUAL WATCH MODE © 2002 Design, 2014 8 Doc. No.
F.10 v.3 OPERATING MANUAL WATCH DEFAULT TIME Default Time is the time that is displayed on the Watch until changed. It is also the time viewed during operation in DC (Dive Computer) modes. Main Time is the current time at your home location and is normally selected as the Watch Default Time. Alternate Time will be the current time at a remote travel location. Upon arrival at the location, Alternate Time can be interchanged with Main Time to make it the Watch Default Time.
F.10 v.3 OPERATING MANUAL • A (< 2 sec) - to step forward through selections of OFF, ON, and SET (Fig. 7B). • M (< 2 sec) - to step back through the selections. • S (< 2 sec) - to save the selection. >> If OFF or ON is selected, operation reverts to the Lead-in screen. >> If SET is selected, the Set CDT screen is displayed. • S (2 sec) - to revert to CDT Lead-in, if no setting change. • M (2 sec), or 2 minutes of no button action, will revert to Watch Default Time. Fig.
F.10 v.3 OPERATING MANUAL SET TIME (& DATE) Sequence >> Lead-in >> Date Format >> Hour Format >> Time of Day >> Date >> Alternate Time >> Default Time >> Show Dual. Set Points remain as set until changed. Set Time Lead-in, information includes (Fig. 12): > Graphics GoTo and SEt t. • • • • S (< 2 sec) - to access Set Date Format. A (< 2 sec) - to step forward to Chrono Lead-in. M (< 2 sec) - to step back to Daily Alarm Lead-in. M (2 sec), or 2 minutes of no button action, will revert to Watch Default Time.
F.10 v.3 OPERATING MANUAL • • • • • A (hold) - to scroll upward through Month Set Points (8/sec) from 1 to 12 in increments of 1. A (< 2 sec) - to step upward through Set Points. M (< 2 sec) - to step back through Set Points. S (< 2 sec) - to save the Month Set Point, replace the graphic MNTH with DAY, and flash the Day digits. S (2 sec) - to step back to Set Year. • • • • • • A (hold) - to scroll upward through Day Set Points (8/sec) from 1 to 31 (max for that month) in increments of 1.
F.10 v.3 OPERATING MANUAL CHRONOGRAPH (Stop Watch, Lap/Run Timer) The Chrono is operational during all modes (Watch, Free Surface, and Dive). Once started, the Chrono remains on the display and continues to run until M is pressed (< 2 sec) to revert to the Lead-in (Go To) screen if in Watch or FREE Surface mode or to the Dive Main if a dive was started while the Chrono was running. It runs unseen in the background when being displayed. Chrono Lead-in, information includes (Fig.
F.10 v.3 OPERATING MANUAL surface mode © 2002 Design, 2014 14 Doc. No.
F.10 v.3 OPERATING MANUAL SURFACE MODE Surface Main is the default screen displayed while in FREE Mode. Like Watch mode, you can access a group of functions including >> ALTs (Countdown Timer and additional data), Set Alarms, Set Utilities, Serial Number, and Chronograph. The CDT is separate from the one featured in Watch Mode. The Chronograph is the same one as Watch Mode with it's operations carrying over between the two modes.
F.10 v.3 OPERATING MANUAL SURF ALT 1 (CDT Status), information includes (Fig. 22): > Graphic TIMR. > Countdown Time (min:sec) with TIME icon, as >> 0:00 if no time has been set, or it completed the countdown; min:sec set if Off (or Auto) and ready to start; min:sec remaining if On (or Auto) with a countdown in progress. > Graphic OFF (or ON, or Auto) flashing. • • • • • • • S (< 2 sec) - to start/stop the countdown. Once started when set for Auto, the countdown repeats until stopped.
F.10 v.3 OPERATING MANUAL • • • • • • • • • • • • A (hold) - to scroll upward through Minute Set Points (8/sec) from 0: to 59: in increments of 1: (min). A (< 2 sec) - to step upward through Minute Set Points. M (< 2 sec) - to step back through Set Points. S (< 2 sec) - to save the Minute setting and flash the Seconds digits. A (hold) - to scroll upward through Seconds Set Points (8/sec) from :00 to :59 in increments of :01 (sec). A (< 2 sec) - to step upward through Seconds Set Points.
F.10 v.3 OPERATING MANUAL Set SRT (Surface Recovery Time) Alarm, information includes (Fig. 29): > Graphic SRT. > Recovery Time (min:sec) with SURF & TIME icons. > Graphic OFF (or ON), flashing upon access. • A (< 2 sec) - to step forward through the selections of OFF, ON, and SEt. • M (< 2 sec) - to step back through the selections. • S (2 sec) - to step back to Set Audible. • S (< 2 sec) - to save the setting. Fig.
F.10 v.3 OPERATING MANUAL Set DD1 (Descending Depth Alarm, DD2 & DA3 similar), information includes (Fig. 32): The Depth Alarms can only be set at progressively deeper depths with DD2 deeper than DD1 and DD3 deeper than DD2, then any of the alarms can be set OFF or ON as needed. > Graphic DD1. > Depth with MAX and FT (or M) icons. > Set Point OFF (or ON), flashing upon access. Fig. 32 - SET DD ALARM • A (< 2 sec) - to step forward through the selections of OFF, ON, and SEt.
F.10 v.3 OPERATING MANUAL Set Water Type, information includes (Fig. 36): > Graphics TYPE and H2O. > Graphic SEA (or FrESH), flashing upon access. • A or M (< 2 sec) - to toggle between SEA and FRESH. • S (2 sec) - to step back to Set Wet Activation. • S (< 2 sec) - to save the setting and access Set Backlight Duration. Fig. 36 - SET WATER TYPE Set Backlight Duration, information includes (Fig. 37): > Graphics GLO and durA. > Time (min:sec) flashing upon access, with TIME icon.
F.10 v.3 OPERATING MANUAL LOG & HISTORY • A (2 sec), while Watch Main Time or FREE SURF Main is displayed, will access and step through Log and History modes. Sequence: Main >> Log >> Day History >> Full History. LOG MODE Log Mode displays information from the latest 99 dives sequentially in reverse order (the most recent first). Log information is retained until over written by another dive. After exceeding 99 dives, the most recent Dive completed will be added to the Log and the oldest deleted.
F.10 v.3 OPERATING MANUAL LOG 4 (Profile) The Log 4 screen allows you to analyze dives on site without the use of the PC interface system. The dive's Depth can be observed while elapsed dive time is increased or decreased throughout the dive beginning at descent. LOG 4, information includes (Fig. 45): > Graphic No with the dive number (1 to 99). > Max Depth with FT (or M) icon. > Log (book) icon. > Graphic Pro, indicating that the screen is displaying interactive Profile data for that dive.
F.10 v.3 OPERATING MANUAL DAY HISTORY 4, information includes (Fig. 49): > Graphics DAY and AVE, indicating that the data displayed represents Averages for all dives conducted that day. > Max Depth with MAX and FT (or M) icons. > Dive Time (min:sec)with DIVE and TIME icons. • A (< 2 sec) to revert to Day History 1 • No button (2 min) to revert to FREE SURF Main or Watch Main Time. • M (2 sec), or 2 minutes of no button action, will revert to the Main.
F.10 v.3 OPERATING MANUAL DIVE MODE Dive Mode is activated upon descent to the DSD (Dive Start Depth) set for 1 second, then the dive ends upon ascent above 2 FT (0.6 M) for the BDSI (Between Dive Surface Interval) time set. If a descent is made while the Chrono is on the display, it will remain on the display (even after a dive is started), until M is pressed/released to display the Dive Main. © 2002 Design, 2014 24 Doc. No.
F.10 v.3 OPERATING MANUAL DIVE MODE Prior to the first dive of a new series, if Wet Activation is set Off, Dive Mode will not activate during operation in any Watch Mode. It must to be in FREE Mode prior to activating Dive Mode. If Wet Activation is set On, Dive Mode will activate from any operating surface mode including Watch modes once the A/d senses the DSD (Dive Start Depth) set for 5 seconds.
F.10 v.3 OPERATING MANUAL WARNINGS & ALARMS © 2002 Design, 2014 26 Doc. No.
F.10 v.3 OPERATING MANUAL ALARMS When Alarms sound, the LED will flash. Also, the Backlight will come On (if Off) for 10 seconds, and a flashing icon or message will be displayed as an indication that an event is occurring and as a reminder to view the display to identify the event. When the Audible stops, the LED will extinguish and the message will clear. If the Audible is set OFF, it will not sound and the LED will not flash for any cautionary situation.
F.10 v.3 OPERATING MANUAL REFERENCE © 2002 Design, 2014 28 Doc. No.
F.10 v.3 OPERATING MANUAL UPLOADING SETTINGS & DOWNLOADING DATA The F10v3 is configured with a Data Port located on the back of the left side that enables it to be connected to a PC or MAC through a USB port using the Oceanic Computer Interface Cable, when viewing the Watch Default Time screen. The Settings Upload portion of the OceanLog or DiverLog program can be used to set/change the Watch Time selections, Set A group selections (Alarms), and Set U group selections (Utilities).
F.10 v.3 OPERATING MANUAL WARNINGS: Never, under any circumstances, poke any object through any slots or holes of the module. Doing so may damage the depth sensor, possibly resulting in erroneous depth displays. If you are in doubt about the accuracy of your unit's depth readings, DO NOT attempt to dive with it until it has been inspected by Oceanic. Never pressure test the module in an air environment. Doing so may damage the depth sensor, possibly resulting in erroneous depth or time readings.
F.10 v.3 OPERATING MANUAL • Using care not to damage the Contact (Fig. 71a), slide the Battery up and out of the Left side of the Battery Compartment. • Discard the Battery according to local regulations governing disposal of Lithium batteries. a CAUTION: DO NOT allow a metal object to short circuit the top of the Battery which is positive (+) to the negative ( - ) contact of the Battery Compartment.
F.10 v.3 OPERATING MANUAL SPECIFICATIONS CAN BE USED AS • Watch • Digital Gauge for Free Dive activity WATCH MODES • Main Time • Alternate (supplemental information) • Countdown Timer • Daily Alarm • Set Time/Date • Chronograph (run timer) • Set Time/Date: Date Format (M.D, D.
F.10 v.3 OPERATING MANUAL SPECIFICATIONS (continued) OPERATIONAL PERFORMANCE Function: • Depth • Timers Accuracy: ±1% of full scale 1 second per day Dive Counter: • Dives 1 to 99, 0 if no dive made yet. • Resets to Dive 1, after midnight or by A+S (2 sec). Dive Log Modes: • Stores 99 most recent dives in memory for viewing. • After 99 dives, adds next dive in memory and deletes the oldest dive. Altitude: • Operational from Sea Level (= 0 to 3,000 feet/915 meters) to 14,000 feet (4,270 meters) elevation.
F.10 v.3 OPERATING MANUAL GLOSSARY Audible Alarm ‑ A emitted tone that alerts the diver to potential danger. Depth Sensor ‑ An electro-mechanical device that converts water pressure into an electrical signal, that is converted to a visual depth display. Display ‑ A visual readout of information. Dive Log Mode ‑ A display of recorded dive information. Elapsed Dive Time ‑ The total time spent underwater during a dive that begins at the start depth set and ends upon ascent to the end depth.
F.10 v.
F.10 v.3 OPERATING MANUAL F.10 v.3 OPERATING MANUAL © 2002 Design, 2014 36 Doc. No.