Operation Manual

20
OCi OPERATING MANUAL
© 2002 Design, 2013 Doc. No. 12-5335-r02 (9/12/13)
SCUBA LOG - NORM & GAUG MODES
Information from the latest 24 NORM and/or GAUG dives is stored for viewing. After exceeding 24 dives, the most recent dive
is stored while the oldest is deleted.
> Dives are numbered from 1 to 24 starting each time NORM (or GAUG) Dive Mode is activated. After the post dive 24 hour
period has elapsed, the fi rst dive of the next operation period is #1.
> 10 minutes after surfacing from dives, the Log screens for that dive as well as all other dives stored can be viewed.
> In the event that a dive’s elapsed time (EDT) exceeds 9:59 (hr:min), the data at the 9:59 interval is recorded in the Log upon
surfacing of the unit.
Surface Main >> Main Menu >> Log Data 1 >> Log Data 2 >> Log Data 3 >> Log Data 4.
LOG DATA 1 (identifi er), information includes (Fig. 25A/B):
> Graphic LOG.
The graphics NO DIVES YET are displayed until the fi rst dive is recorded
> Graphic NO-D (or DECO or GAUG or VIOL).
> Graphic DIVE - with dive number (1 to 24, 0 if no dive recorded yet).
> Time of Day* the dive began (hr:min) with A (or P).
> Day of the week the dive was conducted (MON, etc.).
> Date* the dive was conducted (Month.Day or Day.Month)
*The Times and Dates recorded are based on the Watch Default Time selected. Main (home) Time will be used unless you
have selected ALT Time (away) to be the Watch Default Time prior to the dives recorded.
• A (hold) - to scroll through Data 1 screens 8/sec, from the most recent to oldest recorded.
• A (< 2 sec) - to step through screens one at a time, from the most recent to oldest recorded.
• M (< 2 sec) - to step back through screens one at a time.
• S (< 2 sec) - to access that dive's Log Data 2 screen.
• S (2 sec) - to step back to the Main Menu.
• M (2 sec), or 2 min of no button action, - to revert to the Surface Main.
• L (< 2 sec) - to toggle the Backlight On/Off. Will be On for the duration time set.
• L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.
LOG DATA 2, information includes (Fig. 26):
> Pre dive Surface Interval (hr:min) with SURF icon, 0:00 if Dive # 1.
> Max Depth with graphic FT (or M) MAX.
> Elapsed Dive Time (hr:min) with graphic EDT.
> Graphic SEA (or EL2 to EL7), altitude at which the dive was conducted.
> Temperature with ° icon and graphic F (or C), minimum recorded during that dive.
> TLBG with the max segment fl ashing, others fi xed up to end of dive accumulation. All segments fl ashing if a Violation.
Blank if GAUG.
> VARI, max Ascent Rate sustained for 4 seconds during the dive.
> Nx icon, if any gas was set for Nitrox.
• S (< 2 sec) - to access that dive's Log Data 3 screen, or bypass to Data 4 if no TMT used.
• S (2 sec) - to step back to that dive's Log Data 1 screen.
• M (2 sec), or 2 min of no button action, - to revert to the Surface Main.
• L (< 2 sec) - to toggle the Backlight On/Off. Will be On for the duration time set.
• L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.
LOG DATA 3 (TMT 1 only, bypassed if no TMT used), information includes (Fig. 27):
> Graphic TMT1.
> Start Pressure with graphics PSI (or BAR) and START.
> End Pressure with graphics PSI (or BAR) and END.
• S (< 2 sec) - to access that dive's Log Data 3 screen.
• S (2 sec) - to step back to that dive's Log Data 2 screen.
• M (2 sec), or 2 min of no button action, - to revert to the Surface Main.
• L (< 2 sec) - to toggle the Backlight On/Off. Will be On for the duration time set.
• L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.
LOG DATA 4 (Nitrox only), information includes (Fig. 28):
> % of O2 Saturation when the dive ended with graphics..
> Graphic GAS 1 (or 2, 3, 4), the gas in use when the dive ended.
> FO2 set for the gas in use when the dive ended.
> Maximum PO2 achieved during the dive with icon.
> Nx icon.
• S (< 2 sec) - to access that dive's Log Data 1 screen.
• S (2 sec) - to step back to that dive's Log Data 3 screen.
• M (2 sec), or 2 min of no button action, - to revert to the Surface Main.
• L (< 2 sec) - to toggle the Backlight On/Off. Will be On for the duration time set.
• L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.
Fig. 26 - LOG DATA 2
Fig. 27 - LOG DATA 3
Fig. 25A - LOG DATA 1
Fig. 25B - LOG DATA 1
Fig. 28 - LOG DATA 4