OceanLED Marine Product Support A6 / M6 Gen2 INSTALLATION MANUAL OceanLED This installation manual covers the following products: A6 / M6 Gen2 Above / Below Water Kit Includes M6 or A6 Gen2 Light, Mounting Screws, Fuse Kit OceanLED INSTALL / M6-A6 / 280417 / v7.
IMPORTANT: Please read the instructions completely before proceeding with the installation. These instructions supersede any other instructions if they differ. Chapter 1........................................................................................................................................................................................................4 An overview of the installation. Chapter 2..................................................................................................
IMPORTANT SAFETY PRECAUTIONS! ATTENTION INSTALLER: This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner and/ or operator of this equipment. C CAUTION: Risk Group 2 Possibly hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be harmful to the eye. CLASS 3: This equipment is designed to operate at voltages of less than 50v DC.
Chapter 1: Overview 1 CHAPTER ONE 1.1 Identifying your model To Identify if your light is an M6 (Mast light) or an A6 (Underwater light) please refer to the packaging or label on the rear of the PCB. 1.2 DC Power / Fuse Ratings The majority of installations will utilize onboard 12/24v DC power supply from a marine battery.
Chapter 2: Installation 2 CHAPTER TWO Note: OceanLED makes every effort to protect our marine and fresh water environment as well as our natural resources. Please take care to keep packaging away from and out of the water by ensuring loose packaging materials are secured and not susceptible to being blown into the water. Please recycle all packaging materials as the sustainability of our environment is everyone's responsibility. 2.
1. Apply generous amounts of the sealant you are using to the back perimeter of the light body. Make sure to generously coat the cable of the light where it meets the back of the light. There should be an unbroken bead of sealant around the perimeter of the light unit. 2. Insert the light on to the mounting surface, feeding the cable through first and seat into place. Press the light hard into the mounting surface and ensure good adhesion. 3.
3. If you are not installing a custom fuse panel, it is imperative that the OceanLED supplied fuse is installed on each power line from each light. Please consult electrical specification on page 4 to select the correct fuse. 4. Apply generous amounts of the sealant you are using to the back perimeter of the light body. Make sure to generously coat the cable of the light where it meets the back of the light. There should be an unbroken bead of sealant around the perimeter of the light unit.
Chapter 3: Maintenance, Repair, & Parts 3 CHAPTER THREE NOTE: M6/A6 lights have active thermal protection. This means that under normal ambient conditions they run at full power. Moderate dimming may be noticeable if high ambient temperatures are reached to avoid damage. 3.1 Cleaning Instructions CAUTION: Harsh cleaning solvents will damage the light and Tritonium coating. Sea growth can collect quickly on the light and this can reduce the performance in just a few weeks.
Troubleshooting Common Problems and Their Solutions M6 / A6 Gen2 Light Problem Check Result Fix Light does not look bright. Check light is clean Dirty light Clean light. Check voltage supply to the light is between 9 volts and 28vDC. Voltage is either too high or too low. Investigate reason for high or low voltage and fix. Check voltage supply is stable and does not fluctuate. Voltage is fluctuating. Investigate reason for voltage fluctuation and fix.
Chapter 4: Appendix 4 CHAPTER FOUR SUPPLY CABLE CONDUCTOR SIZE CHART CABLE LENGTH (FEET) CIRCUIT CURRENT 2 AMP 4 AMP 6 AMP 8 AMP 10 AMP 12 AMP 14 AMP 16 AMP 0-5 18 AWG 18 AWG 16 AWG 16 AWG 16 AWG 14 AWG 14 AWG 14 AWG 10-15 18 AWG 18 AWG 16 AWG 16 AWG 14 AWG 14 AWG 14 AWG 14 AWG 15-20 18 AWG 18 AWG 16 AWG 14 AWG 14 AWG 14 AWG 12 AWG 12 AWG 20-25 18 AWG 16 AWG 14 AWG 14 AWG 12 AWG 12 AWG 12 AWG 10 AWG 25-30 18 AWG 16 AWG 14 AWG 12 AWG 12 AWG 10 AWG 10 AWG
Chapter 5: Warranty Statement: 5 CHAPTER FIVE This warranty statement is for those products supplied to and sold from all territories internationally. OceanLED stands by its products. In general terms, the company gives a full 2 year’s manufacturer’s warranty on all of its products from date of sale from OceanLED. Warranty replacements shall be covered for a period of 2 years from the date of the original product sale from OceanLED.
(if there are none) good trade practice; or the defect arises from the corrosion of metal parts or the failure of the Buyer to ensure that Goods are installed correctly, bonded correctly and that there are no active stray currents in the vicinity; or 1.3.3 the defect arises as a result of any default of, or caused by, the Buyer or (without limitation) as a result of misuse, abuse, improper installation, neglect, improper shipping by a party other than the Company; or 1.3.
2.4. Subject to the above Condition 2.3: 2.4.1 the Company’s total liability in contract, (including without limitation negligence or breach of statutory duty), misrepresentation, restitution or otherwise, arising in connection with the performance or contemplated performance of the contract with the Buyer or (without limitation) in respect of the Goods shall be limited to the original purchase; and 2.4.
6.3 Products supplied by a dealer but fitted by the Buyer 6.3.1 If you installed the products yourself, before making contact we ask that you follow the troubleshooting chart for your product, when following the appropriate troubleshooting chart we find that it is helpful to complete the appropriate warranty claim information sheet. Copies can be found in the troubleshoot section of the manual included with the product or alternatively it can be download from our website (www.oceanled.com/documents). 6.3.
NOTES __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ ________________________________________________________
Please remove this page and keep for your files For technical assistance: Europe: service@oceanled.com The Americas: warranty@oceanledusa.com Warranty Serial Code(s): © 2017 Ocean LED Marine LTD All Rights Reserved Specifications are subject to change without notice. Trademarks are the property of Ocean LED Marine LTD OceanLED INSTALL / M6-A6 / 280417 / v7.
