OceanLED Marine Product Support Sport Series DockLight Installation Manual OceanLED This installation manual covers the following products: Sport Series DockLight Single Colour Dual Colour Multi Colour S3116d S3124d S3124d OceanLED reserve the right to change this document without notice. Please refer to www.oceanled.com for latest documentation. OceanLED INSTALLATION MANUAL / DOCK / 270717 / v7.
IMPORTANT: Please read the instructions completely before proceeding with the installation. These instructions supersede any other instructions if they differ. Chapter 1........................................................................................................................................................................................................4 An overview of the underwater light installation and mounting locations. Chapter 2..........................................................
IMPORTANT SAFETY PRECAUTIONS! ATTENTION INSTALLER: This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner and/ or operator of this equipment. CAUTION: (Risk Group 2): Possibly hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be harmful to the eye. CLASS 3: This equipment is designed to operate at voltages of less than 50v DC.
Chapter 1: Overview 1 CHAPTER ONE This handbook provides instructions to assist you in the installation and set up of the Sport DockLight Series lights from OceanLED. 1.1 Identifying your model Single Colour Dual Colour Multi Colour S3116d S3124d S3166d 1.
1.4 Accessories SPORT DOCKLIGHT FLOATING KIT #012108 Optional Easi-Kleen floating bracket mechanism makes it simple to swing the light out of the water to clean. 4 WAY V DC POWER JUNCTION BOX #019901 Provides 4x individually fused outputs. POWER SUPPLY 001-600072 Powers 2 x S3116d Single Colour, or S3124d Dual Colour, or S3166d Multi-Colour Products may vary from image shown. OceanLED INSTALLATION MANUAL / DOCK / 270717 / v7.
Finding The Mounting Location Considerations • Design - Your new OceanLED Dock Light(s) have a wide angle light beam that allows you to engineer a beautiful look around your property. Consider even spacing, boat traffic, tidal fluctuations, storms, seasons, and the overall desired effect when designing your installation. • Depth - Fixed Piling or Bulkhead - The lights should be mounted approximately 300mm - 500mm (UK) / 12" - 20" (US) below mean low water.
Chapter 2: Installation 2 CHAPTER TWO Note: OceanLED makes every effort to protect our marine and fresh water environment as well as our natural resources. Please take care to keep packaging away from and out of the water by ensuring loose packaging materials are secured and not susceptible to being blown into the water. Please recycle all packaging materials as the sustainability of our environment is everyone's responsibility. WARNINGS: • Never use power tools to secure your lights; hand tighten only.
Connecting lights to your DC power source OceanLED Sport models require a 24v DC supply. This supply should be a minimal 3A @ 24v DC per light. It is recommended to connect the light to the DC power source using a two pole, screw type terminal block with a minimum voltage rating of 50V and a current rating of at least 6A. The ends of the cable should be stripped back (if required) and suitable ferrules fitted. The terminal block should be fixed inside a waterproof enclosure (IP66 minimum).
Example connection diagram, single / dual colour: 12/24V DC Fuse Breaker (Not supplied) Power Switch (Not supplied) Red + Fuse Black - Fuse Fuse OceanLED INSTALLATION MANUAL / DOCK / 270717 / v7.
Example connection diagram, multi-colour: Note: When using the Sport Multi Colour docklights in an installation using multiple AC power supplies it is recommended to fit relays into the DC supply side of the installation to allow lights to be controlled together and kept in sync. The relays need to be controlled with a common control switch to interrupt the supply to the lights to enable changing the operation mode of the lights. See below for a connection example.
Power Supply requirements A suitably fused 24v supply is required for each light. DO NOT CONNECT DIRECTLY TO MAINS AC! A 7 Amp fuse / breaker is recommended for each light. When selecting the mains AC to DC converter(s) it is important to ensure that the overall power requirements are met, allowing a ‘reserve’ of at least 15% of the overall power to allow for losses in cable runs.
Chapter 3: Operation, Maintenance, Repair, & Parts 3 CHAPTER THREE 3.1 Dual Colour Operation The Dual colour change has four modes of operation; 1. 2. 3. 4. Single colour white – this mode is entered when the light is first turned on. Single colour blue Fade - Fade between white and blue. Dual colour (blue and white both on) To cycle between the above modes, turn off the light for less than 1 second, then back on again. PLEASE NOTE: Fade mode is not guaranteed to stay in sync between lights over time.
1. Single colour mode – this mode is entered when the light is first turned on. The light will be a single colour, either a default white, or a previously selected colour. 2. Strobe mode – to enter this mode, turn off the light for less than 1 second, then back on again. The light will flash in a pseudo-random pattern - the colour will be the same as that in single colour mode. 3. Cycle / Program mode, to enter this toggle the power to the unit off twice for less than 1 second each time.
Chapter 4: Installation 4 CHAPTER FOUR 4.1 - Cleaning Instructions Sea growth can collect quickly on the light and this can reduce the performance in just a few weeks. To prevent the build-up of sea growth, all OceanLED lights have been coated with a specialized Tritonium coating which makes the surface of the lens a non-stick layer which helps ward off long term barnacle buildup. Lights should be cleaned with a boat brush or similar biweekly or as needed to keep the lens of the light clear.
4.2 Troubleshooting Common Problems and Their Solutions Sport DockLight Problem Check Result Light does not look bright Check that there is no marine growth on the lens. Sea life / Barnacles present Clean the lens as per Chapter 3. Check voltage supply to the light is between 20 volts and 28 volts DC. Voltage is either too high or too low Investigate reason for high or low voltage and fix. Check voltage supply is stable and does not fluctuate.
Chapter 5: Appendix SUPPLY CABLE CONDUCTOR SIZE CHART CABLE LENGTH (FEET) 16 CIRCUIT CURRENT 2 AMP 4 AMP 6 AMP 8 AMP 10 AMP 12 AMP 14 AMP 16 AMP 0-5 18 AWG 18 AWG 16 AWG 16 AWG 16 AWG 14 AWG 14 AWG 14 AWG 10-15 18 AWG 18 AWG 16 AWG 16 AWG 14 AWG 14 AWG 14 AWG 14 AWG 15-20 18 AWG 18 AWG 16 AWG 14 AWG 14 AWG 14 AWG 12 AWG 12 AWG 20-25 18 AWG 16 AWG 14 AWG 14 AWG 12 AWG 12 AWG 12 AWG 10 AWG 25-30 18 AWG 16 AWG 14 AWG 12 AWG 12 AWG 10 AWG 10 AWG 10 AWG 30-3
NOTES __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ ________________________________________________________
© 2018 Ocean LED Marine LTD All Rights Reserved Specifications are subject to change without notice. Trademarks are the property of Ocean LED Marine LTD Ocean LED Marine LTD Unit 1 Jacknell Road Dodwells Bridge Industrial Estate Hinckley, Leicestershire LE10 3BS United Kingdom Tel: +44 (0) 1455 637505 Fax: +44 (0) 1455 238553 service@oceanledusa.com OceanLED INSTALLATION MANUAL / DOCK / 270717 / v7.
