Table of Content V1.1.0 Table of Content ........................................................................... 1 Safety Precautions ....................................................................... 2 Conformity .................................................................................... 5 Listening Cautions........................................................................ 6 Support ........................................................................................
Safety Precautions Do not subject the device to severe impact or drop it from heights. Do not use the device in extreme hot or cold, dusty or damp conditions. Do not expose it to direct sunlight. Avoid using the device near strong magnetic fields. Keep the device away from water and other liquids. In the event that water or other liquids enter the device, power off the product immediately and clean the device.
There is danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type. The battery (battery or batteries or battery pack) should not be exposed to excessive heat such as sunlight, fire or the like. Please follow responsible procedures for battery disposal. If the power adaptor is disconnected from the device, the device will remain operable as long as the battery has sufficient charge.
Note Please only charge the battery while the device is turned off. The charging time will be shorter and the lifetime of the battery will be enlarged. Please fully charge the battery before first use. Note Please note that the internal battery can only be replaced by qualified personnel. If necessary please contact to the ODYS customer service at www.odys.de. Disposal Correct Disposal of this product. This marking indicates that this product should not be disposed of with other household waste in the EU.
Conformity We, Axdia International GmbH, hereby declare that this Android Tablet corresponds to the basic requirements and relevant regulations outlined in guideline 1999/5/EG, 2014/30/EU, 2014/35/EU. The CE declaration of conformity for this product may be found on the following link: www.odys.de – Service – Downloads (http://www.odys.de/web/downloads_de.
Listening Cautions Hearing Safety Listen at a moderate volume: Using headphones at a high volume can impair your hearing. This product can produce sounds in decibel ranges that may cause hearing loss for a normal person, even for exposure less than a minute. The higher decibel ranges are offered for those that may have already experienced some hearing loss. Sound can be deceiving. Over time your hearing ‘comfort level’ adapts to higher volumes of sound.
Support http://www.odys.de support@odys.de On our website you will find the latest information about this product, other products of our enterprise, our company itself and valid warranty terms. The latter you will find under Service Downloads. Firmware upgrades for this device are also offered on our website. For questions or problems read our FAQs on our website or contact our after sales service. The product includes software components licensed under GNU General Public License (GPL).
Appropriate use Device is designed for playing music and video files in commonly used formats, showing photos and access internet functions using the build in Wi-Fi function. It is exclusively meant for this purpose and must only be used for the same. This also includes paying attention to all information contained in this operating manual, especially in the safety instructions. Any other usage is considered to be improper and may lead to material damages and even personal injuries.
Firmware updates (OTA update) ODYS would like to offer an easy and most comfortable way to keep the operating system of your device up-to-date. Using this specially for ODYS Tablet PCs designed App, which you can download from the Google Play Store; you can easily update the system. The ODYS Update App is preinstalled at your ODYS Device. Select, if you would like to update manually or if the system update should be done automatically. Please note that updates improve the capability oft that device.
Feature Summary Wi-Fi Connectivity With the latest Wi-Fi technology, this device can connect you to the Internet wherever you are. Touch Screen Touch or slide your finger on the screen, the screen responds instantly. Third-party Application Support With the built-in Android TM OS, you can install a large number of third-party applications in this device. Please note that you need to insert a Micro SD-Card for it.
Buttons & Ports 1. Micro USB 2. Headphone jack 3. Front camera 4. Earpiece 5. Volume key + / 6. Power button Support for USB stick, Surf stick, Keyboards and Mouse. Note: An OTG supporting adapter cable is required (optional) Charge and power the tablet with the included power adapter. Audio output connection for headphones. Note: The integrated speaker is automatically disabled when headphones are connected to the device. Front-facing camera for taking avatar pictures.
7. Microphone 8. Rear camera 9. Camera light 10. Micro SD slot 11. Micro Sim Slot 12. Speaker turn on or off the device; briefly press the button to turn the screen on or off. Press and hold for 15 seconds to turn off the device if it freezes or behaves otherwise abnormally (Reset). Rear-facing camera for taking pictures. For use with standard Micro SD/SDHC memory card. Accommodates any Micro Sim Card.
Charging Battery The device has a built-in rechargeable battery. No extra battery installation is required. Just charge the device when it indicates low battery. To charge the battery, connect the device to any standard wall outlet via the DC-IN port using the power adaptor. It takes about 6 hours to fully charge the battery. Note: a. We advice to use only the delivered power adapter with this tablet. b. You can operate the device even when it is being charged.
Card Tray - As illustrated, position the device with the camera facing upwards. - Turn the device over with the display facing downwards and place it on a soft base. The card slot should now be at the right. - ①On the upper left corner, slide a fingernail between the - ②Insert the card as illustrate to the right and follow the - ③Close the tray by attaching the cover to the bottom edge and device and cover and use a thumb to gently press against the back of the device.
Installing Memory Card - To use a memory card, find the card slot at the side of the device and then insert the memory card into the slot in the correct. - Push the Micro SD Card card gently and completely into the card slot. Check that the Micro SD card is in the correct position with the contact pin facing downwards as illustrated. You may damage the card and the reader if Micro SD card is not inserted in correct position.
Connect via USB Connect a USB Cable Screen Top Bottom Hooks Please note: Only use connecting cable with a maximum length of 80cm. Please make sure when connecting the USB adapter or connector cables attention to the correct alignment of the connector before inserting it into the USB socket on the unit. Incorrect insertion may cause damage to plug and socket. On the side of the plug there are usually small sizes of hooks that secure the fixation.
Transferring Files Before reading or playing files, you need to transfer media files from a computer to the device. (1) Connect the device to a computer with the supplied USB cable. (2) Once connected, a MTP media device will show on your computer. Containing the internal memory of the device, and the memory card inserted into the device. Now you can copy files from or to these disk drives just as you would on your hard drive. (3) Disconnect the device from the PC safely.
Turning On/Off To turn on the device, press and hold the Power button on the unit until you see the boot-up screen then release. It may take a few minutes to start up the system, please wait before you proceed. To turn off the device, press and hold the Power button until you see the option “Power Off”, tap on “Power Off” and then tap on “OK”. Tip: This device will sleep with the screen off if it stays inactive for a few seconds. You can briefly press the Power button to turn on the screen and wake it up.
Home Screen a. System Hints Informs the user if attached memory or updates are available and other system status information’s b. System settings c. Google Search Bar d. Google Voice Search e. System Settings f. Contacts g. Phone h. Applications Tap on this icon to reveal all applications inicon stalled on your Tablet • You can copy the applications onto the Home screen by pressing and holding on their icons.
j. Browser Tap to launch the Browser to visit your favorite websites. To open the camera app k. Camera l. MS Office m. eManual Manual in ebook format n. Back soft key Tap to return to the previous screen. If the keyboard is on the screen, tap to close the keyboard. o. Home soft Tap to return to the home screen. key p. Running Show apps which are currently running in apps background.
Status bar areas The status bar at the top of the screen is divided into two areas. 1. System hints Wipe from the upper edge towards the centre to open the bar. Here status information and system messages are diplayed.
System settings Wipe the screen top down again to provide direct access to the most important system settings. System information’s like wifi and battery status and the current time will be shown here. Caution! This view may vary and could show different or less elements at your device.
Display all Applications The device supports most of popular third-party applications. It has many useful applications pre-installed, such as music player, video player, photo viewer, alarm clock, calculator, etc. Furthermore, you can add more applications to the device by installing them manually. To display all applications installed on your device, tap the Application Tab. Refer to the figure below.
Using the Touch Screen This device is equipped with a touch-screen. Following are a few tips on how to use the touch screen. Tip: For a proper usage please use your finger. Main Touch Screen Actions - In many applications, you can go back one level in the interface (see below center of the by tapping on the Back icon screen). - Wherever you are in the interface, you can go back directly to the Home Screen by tapping on the Home icon (see below center of the screen).
Other Touch Screen Actions When watching a video or listening to music, you can tap the progression bar to go directly to a different location in the video or song. You can also use your finger to drag the cursor in the progression bar to another location in the video or song. In the file browsers (File, Music, Video, Photo, etc.), you can drag your finger up and down to scroll the file list up and down.
Bluetooth Connection Your tablet is equipped with an integrated Bluetooth technology to enable your device be connected with other Bluetooth devices such as other tablets, mobile phones, headsets or Bluetooth keyboards. Pair other devices (1) Touch the icon for the „Settings“ on the home screen. (2) Tap on “Bluetootth” and if necessary activate the function by tapping on “OFF”. Bluetooth is “ON“ will be displayed. (3) Select the device that you want to pair from the list. (4) Follow the pairing wizard.
Access Internet - Wifi Your Tablet features built-in Wi-Fi technology so that you can access the internet via Wi-Fi network. First of all, you need to configure a Wi-Fi network. For the Wi-Fi configuration procedure to work, you need to be in a Wi-Fi zone that will allow you to connect to it. Every time Your Tablet is in range of a network that you have already configured once, it will attempt to make a connection.
Connect to a WPS capable router This device also supports Wi-Fi Protected Setup (WPS), if your router is WPS capable, you can use WPS button to connect this player to your router. Note: - Consult the user manual of the router and learn how to add a WPS device to the router. - Please use the manual setup if WPS does not work. 1. Press the WPS button on the wireless router. Note: Some router use the WLAN key also for WPS Connections. Please press the WLAN-Key of your Router for 6 Seconds in these cases. 2.
3. Tap on “Wi-Fi”. 4. Activate the function by tapping on “OFF”, if necessary. “Wi-Fi ON” is displayed.
5. Open the “Advanced Wi-Fi Settings by tapping on right hand at the top. 6. Push the “WPS-Push-Button”. 7. Please wait until the pairing is completed.
Manual WIFI Configuring (1) In the Home screen, tap on the Settings icon. (2) Tap on “Wi-Fi”.
(3) Activate the function by tapping on “OFF”, if necessary. “Wi-Fi ON” is displayed. Note: The available network list is constantly refreshed automatically. When the Wi-Fi is enabled, Your Tablet will connect automatically to your configured networks when they are in range. If Your Tablet finds a network that has never been configured, it will display a notification icon.
(4)Tap on the network you want to connect to, enter the required network information (password) and then tap on “Connect”. Your Tablet will now attempt to establish a connection to that WiFi hot spot with the network parameters you entered. If the connection is successful, the message Connected to XXX will appear under the WIFI setting. Advanced Connection To manually scan for available Wi-Fi networks, in the “WIRELESS&NETWORKS” screen, tap the SCAN icon (at top right corner).
Launching the Web browser Tap the Applications icon to display all applications, and then tap the Browser icon to launch the Web browser. If you are already connected to a network, the Web browser will simply open and you can start browsing the Web. To access a new website, tap the Menu icon to display the menu, and input another address. Note: Not all wireless networks offer access to the Internet. Some Wi-Fi networks only link several computers together, without any Internet connection.
Internet Access - UMTS Please note: For Internet connection you need a SIM card plus the respective Internet connection tariff. Configure 3G Internet Connection Note Take care to connect the 3G Dongle while the device is turned off. Normally your provider settings will be set up automatically. If not, please got to „Settings“ – „Wireless & Network“ – „More…“ – „Mobile networks“ – „Access Point Names“ and check if the correct APN was selected and activate it by taping if necessary.
5. Enable the item “Data Enabled” if it is not yet ticked. 6. Select item “Access Point Names” to add an Internet access point. 7. Press the menu button and select “New APN”. Note: The list stays empty if no APN is entered or the connected dongle was not detected 8. Enter the access data obtained from your mobile service provider. Contact your mobile service provider to obtain all required access data, if necessary. 9. Press the Return button to save the settings. 10. The list of set APNs is displayed.
Virtual Keyboard Tapping on any text input field opens the virtual keyboard. Enter a website address or any required text with the virtual keyboard. a. Back-space b. OK / Enter Tabulator c. Shift d. Shift e. Switch between Numbers and Characters f. Space bar g. Emoticons h. Close keyboard Special character Some or the keys provide the possibility to enter special character. (1) Press the corresponding key and keep pressing. (2) While pressing move your finger to the desired character.
Using the Web Browser You can scroll the screen up and down by tapping on the page and dragging it up or down (be careful not to tap a link until you are ready!). To open a link, simply tap it. You can open several web pages at a time, view them all at once on the screen, and then tap one of them to view it in full screen.
Web browser options While a Web page is prompted press the menu key right corner, to open the browser settings. Refresh / Stop Forward NewTab New incognito tab Share page Find on page Request desktop site Never sleep when browsing Save for offline reading Page info Settings at the top Refresh the current page after it was fully loaded / Stops refreshing To open the next page if existing. Open a new tab Open a new tab that will not be saved in the history. There will also be no cookies crated.
Sending/Receiving E-Mails This device has an email app pre-installed. You can send or receive emails via the Internet. Make sure that you have an Internet connection before using the email service. In the Home screen, tap the email icon to access the email app. alternatively, tap on the app shortcut to display all apps and then tap on the email icon to launch the email app.
Setup Email Account First you need to setup an email account for receiving or sending emails. (1) Start up the email app and you are prompted to setup an account. Tap on “Next”. (2) Enter your email address and login password. You can set the account as default by selecting the option “Send email from this account by default”. Tap on “Next”. (3) Enter the required information for POP3/IMAP server. Contact your service provider, network administrator or search for information on the Internet.
Email Menu Email functions are displayed on the right side of the email header. Create new email. Search inbox. Delete current email. Check settings Manage Accounts You can setup more than one account and manage these accounts by checking information about the account, adding a new account or deleting an account. Add New Account Follow these steps to add a new account. (2) Launch the email app, press the Menu icon and tap on “Settings” in the top right corner to display the menu items. Select “Accounts”.
View Emails Access your mailbox when you start up the email app. In the mailbox, wipe with your finger up and down to scroll through the email list. Tap on an email to open it.
Phone Caution The phone function is only available if a valid SIM Card was set in previously. Please note that a SIM card can only be set in when the device is turned off Tap the icon at the start screen to access the desired function as below.
Phone Functions After accessing the Phone function you will see the following interface. Tap in the desired phone number or use one of the other functions.
Call settings Open the call settings to change the settings for your Mailbox, quick dial or caller ID. Write a SMS/MMS Tap at SMS/MMS to write a short message.
People Tap at this shortcut to manage your contacts list.
Playing Music Tap the Applications shortcut to display all applications and then tap the Music icon to enter the music mode. Music Library You should enter the music library once you start the music player. The Music Library shows your music files sorted by categories (Artist, Album, Title, Genre, etc.) if your music files contain these song information tags. If some of your music files do not contain information tags, they will be classified as (Unknown) in the Music Library.
Playback Screen a. Shows that the player app is running, if running in background. b. Show current playlist. c. Random playback on / off. d. Change replay mode e. Search for tracks f. Menu button – Further functions g. Back to Music Library h. CD cover (if any) i. ID3 informations (Performer, Album) j. Short press – Previous track Keep pressing – Fast rewind l k. Play/Pause l. Short press – Next track Keep pressing – Fast forward m.
To pause or resume the playback, tap on the Pause / Play icon. To play the previous/next song, tap on / . You can tap on the progression bar to go directly to a different location in the song. You can also drag the cursor in the progression bar to another location in the song. Tapping continuously on the ID3 information tag will search for the information about the track from the Internet.
Photo Playback Tap on the app icon to access all apps and tap on the photo icon to launch the photo folder. Thumbnails The first screen in photo mode shows all photos/videos and sub folders in the device or on memory card as thumbnails. Tap on a photo thumbnail to view the photo in full screen mode. Open the sub folder if the photo is stored in a sub folder to display the photo/video contents as thumbnails.
View Photo Back to previous view Edit image Share image Open App-Menu While viewing photos tap on the screen to show the status bar at top and bottom. Press the menu button or tap on the respective icon ( ) in the top right corner and then on “Slide Show” to start the slide show. Tap on the screen again to end the slide show. Wipe with your finger to the left or right over the image to display the previous/next photo.
Camera usage The camera can be used for capturing photos or videos of for internet video calls. Smile recognition HDR capture Normal mode Switch Camera Live Photo mode Shutter Video recording Face beauty mode Settings Panorama mode Image settings Exposure Szenen mode White balance Color effect Zoom Simultaneously tap with two fingers at the screen. Drag the fingers together or apart to zoom out or in.
Change the camera Tap at to toggle between front and rear facing camera. Camera settings Tap at to open the settings. Tap at the desired symbol to open. Setting GPS Location Info Image Properties Anti - Flicker Restore defaults Setting ZSD Voice Capture Face Detection Self Timer Continuous shot Picture size Preview size Value Ein /Aus Settings for sharpness, colour and saturation (high, middle, low) Ein /Aus Value ON / OFF ON / OFF ON / OFF OFF, 2 sec, 10 sec.
Setting Noise reduction EIS Microphone Audio Mode Time lapse interval Video quality 56 Value ON / OFF ON / OFF ON / OFF Normal OFF, 1 sec, 1,5 sec or 2 sec Medium, Low, high
ES File Explorer On the Home screen tap on the app icon to access all apps and tap on the explorer icon to launch the ES Explorer Screen elements path Quick Access Quick Access hidden App configuration Higher level of the file current file Menu bar Quick Access The main elements and places of memory are accessible directly from the rapid access at the left edge.
Progress From the path at the top, you could follow the file in which you are. - Press the left side of the progress bar to exit the current file. - Press the right side to access the path or select another location Note If you reached already the lowest level of the file, the left side is no longer present. Window management If a new item is opened via a quick access, it will be opened in a new window.
General Standard path is the internal SD card. Tap on the history above to toggle between connected storage media. External storage devices are in folder “mnt”: sdcard Usable internal device memory. external_sd Connected microSD memory card. usb_storage USB storage media, which are connected via USB adaptor. Navigate Files and Folders Wipe with your finger up and down to scroll through the file list. To open a file or folder, tap the file/folder.
Press and hold for (ca. 3 Seconds) on a file or folder to select it and to show other functions. . Below you can select multiple files or other folders Copy selected items Cut selected items. Delete selected items Rename selected items Additional features Copy/Move Files and Folders (1) In the file list, scroll up and down by wiping with your finger to select the file/folder to be copied or moved. (2) Hold your finger on the selected file/folder until a pop-up menu appears.
Delete Files and Folders (1) In the file list, scroll up and down by wiping with your finger to select the file/folder to be deleted. (2) Hold your finger on the selected file/folder until a pop-up menu appears. (3) Select “Delete” from the pop-up menu, then select “Delete” to confirm or “Cancel” to cancel deleting. Rename Files and Folders (1) In the file list, scroll up and down by wiping with your finger to select the file/folder to be renamed.
Manage Third-party Applications Your Tablet provides support to many useful third-party applications. You can purchase the applications to add more functions to your device. They are available online at the Internet or directly on your product. Pre-installed Applications The device has pre-installed applications when it was manufactured. You can see them by tapping Application Tab. They are video player, audio player, photo browser, calculator etc.
Uninstall Applications (1) Tap the Settings shortcut in the Home Screen to display all system settings. (2) Select “Applications”. (3) Tab on the application that you want to uninstall. (4) Tab on “Uninstall” to uninstall the application. Note: You cannot uninstall the pre-installed applications. Some of the applications developed for Android mobile might not run properly in the Tablet. Please consult the respective software developer for further information or support.
System Settings On the Home screen tap on the “Settings” icon and select the category “Wireless & Networks”, “Sound and Display”, “Date and Time”, etc. Tap on the function to change the settings. Tap on the tick box on the right side of the parameter to enable this option. Wipe with your finger over the screen to display further settings outside the screen. After completing your settings tap on the icon to return to the setting menu or tap on the icon to return to the Home screen.
Device Display Brightness Wallpaper Auto Display Rotation Sleep Daydream Sound and notifications Storage Font Size Rotating the device Coordinate system of the acceleration sensor Predefined profiles Set screen brightness. Select wallpaper. Automatic display rotation when rotating the device. Set auto off delay and screen lock. Press On/Off once to switch on again and tap on the screen once to unlock the screen. Settings for the screen saver “Daydreams”. Change the menu font size.
Battery Apps User Display of the current consumption and status of the battery. This screen allows Android™ apps management. Info display of apps installed on your device. Setting for installation and synchronization with different user accounts. Personal Location Services Security Accounts Language & Input Method Backup & Reset This screen allows certain Android™ apps to determine their current location. Set security parameters and screen locks.
Troubleshooting Touch screen does not respond Ensure that the app provides full touch screen support. Do not tap too hard on the screen; this can cause malfunctions. No sound from earphones Ensure that the volume setting is not too low and that the connection is ok. Ensure that the earphones are clean. Corrupted MP3 files can cause different noise or cannot be played. Ensure that the files are not damaged. Try different earphones.
Solve Wi-Fi connection problems 1. Open Wi-Fi settings. 2. Select and remove Wi-Fi. 3. Tick “Display Password” and enter password. 4.
Reset this device If the Power button does not reset your device, use the “pinhole reset” button, located on the back the device. Touch-screen Problems Check if the Application you are using has full touch-screen support. Don’t press too hard on the screen. This might cause a wrong behavior. No Wifi connection Take care that Wifi is enabled and a wireless network is in range. Be sure that you entered the correct password. Take care of special characters and capital letters.
Specifications Configurations CPU Intel Atom x3 Quad-core up to 1,2GHz DDR 1GB DDRIII Ram Built-in operating Android OS 6.0 system IBM PC or compatible PC, Notebook or Hardware Macintosh with USB port Internal 8GB Memory Memory Card Micro SD card: up to 32GB(SDHC) System Requirements Operation Windows2000/XP/Vista/windows 7and System MAC OS 10.4 or above USB Interface USB2.0 High speed Features Output Port 3.5mm earphone port, built-in speaker Built in microphone E-book Format EPUB, PDF MP3 (MPEG1/2/2.
Technical Parameter Read speed 8.7-9MB/S (MLC flash) Write speed 4.5-4.8MB/S (MLC flash) MP3: 8～320Kbps Audio Bit Rate OGG: 16~320 Kbit/s WAV: 8~48 kHz AVI (Max.1280X720); (Max.1280X720); Video MKV (Max. 1280X720); MOV (Max. Resolution 1280X720) Max. 6Mbps (MPEG4, XVID, DIVX4/5/6); Max. 2.5Mbps (H.264, Real video Video Bit rate 8/9/10); Max. 2Mbps (Sorenson H.263). Photo JPEG (Baseline) (Max.8000*8000), Resolution GIF(Static) (Max.1000*1000) Wi-Fi (802.
Physical Parameters Storage Temp. -20°C ～ +65°C Ambient Temp.
License conditions Copyright (c) 2013 AXDIA International GmbH License terms of AXDIA International GmbH, hereinafter referred to as AXDIA: The firmware packages provided by AXDIA contain files that are made available under various licenses, especially one or various open source licenses (GNU General Public License, GNU Lesser General Public License, or FreeBSD License). AXDIA grants you the right to use the firmware packages, which are made available as object code format.
Warranty Conditions The following conditions comprise the requirements and scope of our warranty conditions and do not affect our legal and contractual warranty obligations. We offer a warranty on our products in accordance with the following conditions: 1. We will resolve damages or defects on our products free of charge within 12 months of the purchase date under the following warranty conditions.
3. The warranty claim does not apply if repairs or other work is carried out by unauthorized persons or if our products are equipped with additional parts or accessories that are not approved for our products. 4. Warranties that have been activated do not cause the warranty period to be extended, nor do they trigger a new warranty period. The warranty period for any replacement parts installed ends with the warranty period for the entire product. 5.
Asserting a warranty claim 1. To make use of the warranty service, you must contact the AXDIA Service Center by e-mail, fax or phone (see below for contact details). You can also use the service form on our website or on the back of the warranty conditions. 2. AXDIA Service Center will try to diagnose and solve your problem. If it is determined that a warranty claim exists, you will be given an RMA number (Return Material Authorization) and you will be asked to send the product to AXDIA.
Service outside of warranty AXDIA can refuse any service claim made that is not covered by the warranty. If AXDIA agrees to provide a service outside the warranty, the customer will be invoiced for all repair and transport costs. AXDIA will not accept any packages that have not first been approved by AXDIA by means of an RMA (Return Material Authorization). .
