DVD MULTIMEDIA RECEIVER 4.
Table of Contents Safety Information .......................................................................................................... 3 Care and Installation ...................................................................................................... 4 Wiring Diagram .............................................................................................................. 5 Controls ......................................................................................................
Safety Information Installation Please read all instructions prior to installation and operation It is highly recommended to have a professional installer or an authorized dealer install your CH-4100 multimedia reciever. This product is only for use in vehicles with 12VDC negative ground only. The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to prevent driver distraction.
Installation Care and Installation Care and Maintenance 1) To clean the monitor or front panel, wipe only with a dry silicone cloth or soft cloth and neutral detergent. Do not use a stiff cloth, or volatile solvents such as paint thinner and alcohol. They can scratch the surface of the panel and/or remove the printing. ) It is recommended to use a cleaning disc in this unit more frequently then the player in your home, since your vehicle is exposed to different environmental conditions.
Wiring Diagram iPod (NOT INCLUDED) VIDEO OUTPUT 1 OPTIONAL TFT MONITOR OPTIONAL TFT MONITOR VIDEO GAME (NOT INCLUDED) MULTI-ZONE A/V OUTPUT VIDEO OUTPUT 2 Installation OPTIONAL TFT MONITOR XM DIRECT TUNER AND ANTENNA (NOT INCLUDED) A/V AUX IN iPod CABLE (INCLUDED) CENTER BACK-UP CAM PARKING BRK (-) XM Cables (INCLUDED) iPOD YELLOW / BLUE XM AUDIO LEFT/RIGHT SUBWOOFER iNPORT ADAPTER (INCLUDED) OPTIONAL BACKUP CAMERA XM DATA OPTIONAL POWER AMPLIFIERS AM/FM ANTENNA NAV INPUT Parking Lamp
Controls Reset Button 6 Controls 1 2 7 3 8 4 9 5 10 Button Operation 1) EJECT - Press once for DISC ejection 2) MUTE - Press once to MUTE audio, press again to return audio. The volume icon will change. 3) VOL / SMART DIAL - Rotate knob Q or P for desired VOLUME level. Rotate clockwise/counter clockwise to select desired item in any MODE and press once to ENTER. Press and hold to access AUDIO menu. device. Do not obstruct, or spray with any cleaning solution.
Remote Control Main Remote Buttons 1) Pull the battery insulation tape out before using IR remote 3 2 4 9) 10) 11) 1 ) 5 30 6 7 26 24 22 29 9 28 10 27 12 25 13 23 15 21 17 13) 14) 15) 16) 17) 18) 19) 0) 1) ) 8 11 19 14 16 18 3) 4) 5) 6) 7) 8) 9) 30) 20 Insert / Replacing the Battery: 1. . 3. 4. 5.
Multi-Zone Remote Multi-Zone Remote Buttons Controls Pull the battery insulation tape out before using IR remote 1) ) 3) 4) 5) 6) 7) 8) 9) 10) 11) 1 ) 13) 14) 15) 16) 17) 18) 19) 0) 1) R-SRC - Selected playing sources Mute - Toggle on/off audio output GOTO search - Search function in the VCD/ DVD disc Root - Main DVD disc menu Up/Down/Left/Right - Navigating system for selection. Next - Select the next chapter/track for playback.
Monitor Operation Safe Monitor Operation • • • The vehicle must be in park and the parking brake applied to view video on the in-dash monitor. The video display of the in-dash unit will not operate while the vehicle is moving. As a safety feature, a blue “PARKING” screen will show on the display when the vehicle's parking brake is not engaged. DVD, AV1 audio can be heard while the vehicle is in motion. It is illegal in most states for the driver to view video while the vehicle is in motion.
General Operation Power On / Off Press the VOL/SMART DIAL once to turn on the unit. Once on, press to MUTE sound, press again to restore sound. To turn off, press and hold. The unit can also be turned on using the remote. Volume Adjustment Operation Adjust the Volume using the VOL/SMART DIAL knob or the remote to adjust the volume to the desired listening level. The volume is set at a default value.
Main Access Menu Main Access Menu The MAIN menu can be access by pressing the MENU button on the remote or by touching the Area A (upper left hand side) on the monitor. 5 1 2 3 4 Touch Access Buttons 1) ) 3) 5) 6) 7) 8) 9) Operation 4) Touch to access AM/FM TUNER mode. Touch to access CD/DVD mode, CD/DVD must be inserted. Touch to access XM MODE. (XM Receiver must be connected to activate). Touch to access iPOD mode.
General Set Up Menu GENERAL Setup Menu Table Settings Default Radio Operation USA Clock adjust AM Clock Mode 12Hr Camera Image Video Format Bluetooth OSD Menu Normal Auto Off English Options USA Korea S-AMER1 China S-AMER2 Arabia Europe HH:MM 12Hr 24Hr Normal Reverse AUTO NTSC PAL Off On English Function Set to appropriate setting for your Country See adjusting the clock for more details PM 6:00 18:00 Normal Image Mirror camera input image 180 degrees System will auto detect NTSC or
Adjusting the Clock 12 or 24 Hour Clock Mode correct hour. Touch Area A of screen Touch arrow to EXIT setup Operation Touch GENERAL setup button If you desire 24Hr format, select 24Hr from CLOCK MODE Touch AM or PM to set Touch OK. Touch 00:00 area in the CLOCK row to set the hour. Keypad should appear. Enter Touch 00:00 area. Enter correct minutes.
Screen Setup Screen Setup Functions Operation Settings Default Options Brightness 10 0 to +20 Screen Saver On Touch Screen Calibration No On Off No Yes Version Function Press the < / > buttons on the remote, touch the (-) or (+) buttons on the screen or rotate the SMART DIAL to adjust the BRIGHTNESS to the desired setting Select On to activate the screen saver, Off to deactivate Touch Yes to enter the Touch Screen calibration mode Software version of unit Touch Screen Calibration It may becom
Audio Signal Processing (ASP) ASP Configuration Menu Settings Bass Freq Default 60 Hz Treble Freq 15KHz Sub Filter 80Hz 0° Bass Q-Factor 1.5 10KHz, 12.5KHz, 15KHz, 17KHz 80Hz, 120Hz, 160Hz 0° 180° 1.0, 1.25, 1.5, 2.0 Select the desired frequency to obtain the best bass effect. Sets a cut off frequency of the subwoofer's LPF (low pass filter) and the "SMALL" speakers HPF (high pass filter).
AM/FM Tuner Operation AM / FM Tuner Screen 1 2 3 4 19 5 6 Operation 18 17 16 7 15 14 1) 13 12 Current souce MODE. Touch to access MAIN menu. TUNER, DVD, XM*, iPod*, CAMERA, Bluetooth, NAVi*, AUX are indicated in the OSD (On Screen Display).
AM/FM Tuner Operation Auto Seek Tuning Press the button to auto SEEK up the next strongest station. Press the button to auto SEEK down the next strongest station. Manual Tuning button to manually tune up one step at a time. Press the button to manually tune down one step at a time. Operation Press the Auto Store (As) Press and hold AS/PS for more than 2 seconds to automatically store the twelve strongest stations in the current band.
DVD Information DVD Region Management Some DVD discs can be played only in certain playback modes according to the intentions of the software. As the CH-4100 plays discs according to their intentions, some functions may not work as intended. Please be sure to read the instructions provided with each disc. This player has been designed to play back DVD software that has been encoded for specific region areas.
Initializing Parking Brake SAFETY WARNING • • • The video display of the in-dash unit will not operate while the vehicle is moving. As a safety feature, “ENGAGE PARKING BRAKE” blue screen will show on the display when the vehicle's parking brake is not engaged. Video display on the front monitor isn't allowed until the PARKING BRAKE is active, however, DVD and AV1 audio can be heard while the vehicle is in motion without engaging the parking brake. This is a safety feature to prevent driver distraction.
DVD Operation DVD Loading Slot Eject button Disc Indicator Light Blue light indicates no disc, otherwise light is red Insert CD/DVD with label facing upwards DVD Notes: 1) ) If PARENTAL Lock is activated and the disc inserted is not authorized, a 4-digit code must be entered and/or the disc be authorized.( see "RATING MENU") Only one disc can be inserted at one time. Inserting a DISC When inserting a DVD disc, it will play automatically.
DVD Controls Touch the PLAY button or on the front panel to resume disk playback. ) Touch the PAUSE button again to suspend the disc playback. 3) Touch 4) Touch the REVERSE button to FAST REVERSE on DVD, 2x, 4x, 8x to 20x. 5) Touch the FF button to FAST FORWARD on DVD, 2x, 4x, 8x to 20x. 6) Touch the Repeat to scroll through the following: button to STOP playback, touch DVD 1) or OK on the remote to resume playback.
DVD Search Function Searching a DVD Touch the search button in AREA F. DVD Searching by Time, Title or Chapter in the TIME area. 1) Touch the ) A touch keypad will now appear, enter your desired TIME to search. 3) Enter OK. Direct Chapter / Track Selection During DVD and CD playback, you can use the numeric keypad on the IR remote to access tracks directly Viewing an Alternate Picture Angle (DVD Only) Some DVD's contain scenes that have been shot simultaneously from different angles.
DVD Setup Menu - Language 2 DVD VIDEO 7 T: 4/16 C: 1/20 00:01:42 USER LOUD ON 08:06 Rear:OFF 3 4 6 8 1 1) Indicates current source playing. ) Indicates that the fourth of sixteen title on the DVD is currently playing. 3) Indicates that the first of twenty chapters on the DVD is currently playing. 4) 5 Indicates the playback time if the current title. 5) Indicates the USER defined EQ levels or decoding mode when listening to a DVD with 5.1 surround sound.
DVD Setup Menu - Video Video Setup Menu With the monitor open in DVD mode and DVD disc inserted, press the AREA A (top left screen) to display the MAIN menu bar. Press DVD Setup to access the DVD setup menu. DVD Press VIDEO icon to select from the following menus: NORMAL- 4:3 TV Shape Press to select desired TV Shape. WIDE - 16:9 Angle Mark Press to select desired Angle Mark. Video Mode Press to select desired Video mode.
DVD Setup Menu - Ratings Ratings Setup Menu With the monitor open in DVD mode and a DVD Disc inserted, press the AREA A (top left screen) to display the MAIN menu bar. Press DVD Setup to access the DVD setup menu. DVD Press RATING icon to select from the following menus: Enable Parental Lock Password Press ---- to enter a your desired password.
DVD Setup Menu - Audio Audio Setup Menu With the unit in DVD mode, press Area A to display the MAIN menu. Press DVD Setup to access the DVD setup menu. DVD Press the AUDIO button to access the following menus: Audio Settings The Pink Noise generator is used to set the relative speaker levels for multi-channel playback. Press to activate Pink Noise generator for desired channel.
DVD Setup Menu - Speaker Speaker Setup Menu With the unit in DVD mode, press Area A to display the MAIN menu. Press DVD Setup to access the DVD setup menu. DVD Press the SPEAKER button to access the following menus: Settings Default Options Function Full 6CH 6-channel mode Speaker Mode DownMix DownMix Front* Large Surround* Large Subwoofer* None Center* None Large Small Large Small None Present None Large Small None Speaker Selection 2-channel mode.
DVD Setup Menu - Surrround I Speaker Setup Menu With the unit in DVD mode, press Area A to display the MAIN menu. DVD Press DVD Setup to access the DVD setup menu. Press the SPEAKER button to access the following menus: Decode Mode Panorama Mode* Off Surround Matrix Movie Music Off = Default On Panorama ON extends the front stereo image to include the surround speakers for a wrap around effect.
CD/DVD/MP3/WMA Information Media Compatibility The following types of discs/files are compatible: • CD-ROM (ISO), CD-R, CD-RW, DVD+R/RW, DVD-R/RW, DVD-R/DL • CD-DA, DVD Video • MP3 data • WMA data Some recordable DVDs and CDs may be incompatible with this unit, depending on media type and recording method. Playback Order MP3/WMA playback sequence is based on recorded order of files and begins in the root folder of the disc. Any empty folders or folders that do not include MP3/ WMA files are skipped.
CD Operation 1 2 3 4 18 17 5 6 16 7 15 CD 14 13 12 11 1) Current source indicator, touch AREA A to access MAIN source menu ) Disc title. 3) Track title. 4) Current TIME. 5) Touch to activate / deactivate REPEAT: Single mode. 6) Touch to activate / deactivate RANDOM mode. 7) Touch to access the DIRECT TRACK access keypad 8) Touch to SCAN CD tracks for 5 sec each track, touch again to deactivate. 10 9) 9 8 Touch to FAST FORWARD current track.
MP3/WMA Operation 1 3 2 4 15 12 16 13 17 14 18 5 6 7 8 9 10 11 Current source indicator, touch AREA A to access MAIN source menu 11) Touch to FAST FORWARD MP3 tracks, touch PLAY to deactivate. ) Disc title. 1 ) Touch to activate / deactivate REPEAT: Single mode. 3) Track title. 4) Current TIME. 5) Touch to PLAY / PAUSE disc playback. 6) Touch to STOP disc playback. 7) Touch to PAGE down. 15) Current track and total number of tracks on the disc. 8) Touch to PAGE up.
iPod Operation 1 3 2 4 18 12 19 13 14 15 20 To switch to iPod press the MODE button on the front panel or IR remote or from the MAIN source menu 16 21 17 iPod 5 6 7 8 9 10 11 1) Current source indicator, touch AREA A to access MAIN source menu ) Disc title. 3) Track title. 4) Current TIME. 5) Touch to PLAY / PAUSE disc playback. 6) Touch to STOP disc playback. 16) Touch to access DIRECT SONG access keypad. 7) Touch to PAGE down. 17) Touch to display song list.
iPod Operation Notes: 1. PHOTO FILES are only compatible with NANO and G5 iPod 2. VIDEO FILES are only compatible with G5 iPod Playing Photo or Video File From iPod 1) Make sure the following options through the iPod video settings menu are set to: TV Out = ON, Signal = NTSC and Widescreen = ON.* ) Touch VIDEO icon 3) Press PLAY on your iPod, video should now appear on the Monitor *Consult your iPod owners manual for details.
XM Radio Operation Activating Your XM Receiver (when connected): 1) ) 3) 4) 5) 6) Touch top left corner of screen. Touch to access XM MODE, XM Receiver must be connected to activate Verify channel 1 (XM Preview Channel) is playing. Select Channel 0. The XM receiver’s eight character Radio ID number will appear on the CH-4100 display. The Radio ID number is also located on the XM receiver unit (sold separately).
XM Radio Operation Tuning Modes Touch to select between XM, XM1, XM2 and XM3 bands. Channel Slection Touch momentarily to select the next available channel. Storing and Recalling Preset Channels Up to 48 XM channels can be stored. To store a channel, select XM, XM1, XM2 or XM3 band and the desired channel. Press and hold the desired preset button (1-12) for more than 2 seconds. When stored, the preset number will now be highlighted by a box and the station will appear in the display.
Bluetooth Operation Activating Bluetooth Operation Select Bluetooth option in the General Setup (see page 11 to access General Setup) and select ON to activate the Bluetooth feature. From the Main Menu, touch the Bluetooth icon on the screen. 1 2 3 4 11 10 5 9 8 Bluetooth 7 6 1) Displays current mode. 5) ) Press Talk Button to answer an incoming call or to place an outgoing call. 3) Display Indicator showing the phone number and call status.
Bluetooth Operation Bluetooth Setup Pairing Access Bluetooth setup menu and press YES option on the screen, then "Wait Pairing..." will display. Now you can pair a mobile device with the unit. When prompted by your mobile device, enter 1234 for the PIN or pass code. After the pairing process has completed, the Bluetooth icon will turn solid blue. This unit can remember more than 4 mobile devices. The head unit will delete the phone that was least used to allow for the new pairing (connection).
Navigating Operation Accessing Navigation Access the MAIN menu by pressing the NAVI button on the front panel, pressing the SRC button on the front panel or touching Area A or the upper left hand corner of the screen and select the NAVI button to enter the Navigation Operation interface. Notes: SNAV-1 , SPiN3510 or SPiN3550 must be connected to access navigation mode. Navigation Operation Please refer to the SNAV-1 or P-NAVi navigation user manuals.
Multi-Zone Operation Multi-Zone Operation Independent sources can be played simultaneously on the unit. For example, the AM/FM tuner can be selected for the front zone, while the DVD video is selected for the Mult-Zone source (for headrest monitors, overhead monitors, etc.) Multi-Zone Menu Access 1. The MAIN menu can be access by pressing the MENU button on the remote or by touching the Area A (upper left hand side) on the monitor. .
Multi-Zone AM/FM Tuner 2 1 3 13 4 5 12 11 10 Multi-Zone 8 1) Indicator for MAIN ZONE ) Displays current time on CLOCK INDICATOR 3) Indicator for MULTI-ZONE 4) Page up/down arrow for PRESET PAGE 5) Shows the preset station list by frequency for the PRESET NUMBER LIST DISPLAY. Touch and hold frequency to store presets. Touch the TUNER SCAN to scan through all available stations in the current band.
Multi-Zone XM Radio 2 1 3 12 4 11 5 10 9 8 1) Indicator for MAIN ZONE ) Displays current time on CLOCK INDICATOR 3) Indicator for MULTI-ZONE 4) Displays the CHANNEL NAME 5) Displays the TITLE of the current song 6) Touch CHANNEL SCAN to scan through all available available channels, pausing for 10 seconds on each channel. Touch again to cancel. SCAN will change to green when the scan function is active.
Multi-Zone iPod 2 1 3 13 4 12 5 11 Multi-Zone 10 42 9 1) Indicator for MAIN ZONE ) Displays current time on CLOCK INDICATOR 3) Indicator for MULTI-ZONE 4) Displays the TIME ELAPSED of the current song 5) Displays the NAME of the artist for the current song 6) Touch SONG SCAN to scan through all available available songs, pausing for 10 seconds on each song. Touch again to cancel. SCAN will change to green when the scan function is active. 7) Touch to access VIDEO MODE.
Limited One Year Warranty Limited One Year Warranty Applies to Multimedia Headunits Who is covered? PRIORITY AUDIO (the Company) extends this warranty to the original retail purchaser of products purchased through an authorized PRIORITY AUDIO retailer in the U.S.A. or Canada. This warranty is not transferable or assignable.
Troubleshooting Problem Unit will not turn on (no power) Unit has power (but no sound) Basic Unit Operation Unit blows fuse Cause Check connections for proper voltage (11~16VDC) Black wire not connected Check connection to ground Fuse blown Replace fuse Speaker wires not connected Check connections at speakers One or more speaker wires touching each other or touching chassis ground Insulate all bare speaker wires from each other and chassis ground Yellow or red wire touching chassis ground Ch
Troubleshooting XM Radio Problem Cause OFF AIR appears on display The selected channel is not in service The antenna cable is damaged Try another channel Check for pinched or cut antenna cable No song title or artist name is displayed This information may not be available for some music channels, news channels, or when there is no song playing This condition is normal, there is nothing wrong with your receiver You can not receive any XM channels Your XM Radio receiver is not activated Contact XM
Notes 46
Specifications General Operating voltage: 11-16 VDC, neg. gnd Speaker output impedance: 4~8 ohms Line output voltage: 2 Volts Line output impedance: 200 ohms Chassis dimensions: 2" x 7" x 7" (51 x178 x178 mm) FM Tuner Tuning range: Usable sensitivity: 50dB quieting sensitivity: Stereo separation @ 1kHz: Frequency response: 87.5MHz-107.9MHz 8.
OE RADIO Toll Free: 1-877-305-8972 www.oeradio.com ©2007 PRIORITY AUDIO All rights reserved.
