Installation Manual

ManualsBrandsOFM ManualsChairs & SofasOFM 130-DK-A05 Mesh Comfort Series Ergonomic Task Chair with Drafting Kit

Chair Back

1 Unit

Chair Seat

1 Unit

Seat Mechanism

1 Unit

Casters

5 Units

Gas Lift

1 Unit

Telescopic Bellows

1 Unit

8x20mm Screws

4 Units

Chair Base

1 Unit

Models 130/130-AA3/130-AA3-DK/130-DK Modern Mesh Ergonomic Task Chair

Parts Listing

161 Tradition Trail, Holly Springs, NC, 27540

800-520-7471 (voice) 919-362-4765 (fax)

919-303-6389 (voice) www.ofminc.com

support@ofminc.com

Assembly Notes:

During assembly, hand tighten screws only. When all screws

are in place, you may then tighten all screws completely.

CAUTION:

1. Do not use this chair as a step ladder.

2. Check for loose screws and tighten them every 6 months.

WEIGHT CAPACITY: 250 lbs.

12.12.13

STOP

Assembly Instructions:

Tools Needed: Philips Head Screwdriver

Please read all instructions before assembly.

Step 1: Insert Casters (D) into Base (H).

If you are assembling a model with a DK Foot Ring please proceed

to subsequent pages for drafting kit assembly instructions.

Step 2: Insert Gas Lift (E) into Base (H).

Step 3: Cover Gas Lift (E) with 3 piece Telescopic Bellows (F).

Step 4: Place Chair Seat (B) upside down on a level,

non-abrasive surface and align pre-drilled holes in

Seat Mechanism (C), with holes in Chair Seat.

Step 5: Insert four 30mm Screws (G) through holes in the

Seat Mechanism (C), and into the Chair Seat (B).

Tighten with screwdriver.

If you are assembling a model with optional Adjustable Arms please

proceed to subsequent pages for armrest assembly instructions.

Step 6: Carefully place Chair Seat (B) with attached Seat

Mechanism (C) onto the Gas Lift (E), aligning the hole

in the Seat Mechanism with Gas Lift. Press down

on Chair Seat to secure onto Base (H).

Step 7: Slide Chair Back (A) with attached back support bar

into the slot on Seat Mechanism (C).

Step 8: Hand tighten tension knob on Seat Mechanism (C)

until the Chair Back (A) is properly secured.

Step 9: Carefully sit on chair to make sure the Gas Lift (E)

is properly inserted into the Base (H).

Step 10: Operate the Gas Lift lever on the Seat Mechanism (C),

to be sure unt is working properly.

Step 11: Readjust Chair Back (A) by loosening tension knob

on the Seat Mechanism (C) accordingly, for your

personal comfort.

Summary of content (3 pages)

PAGE 1
Models 130/130-AA3/130-AA3-DK /130-DK Modern Mesh Ergonomic Task Chair Parts Listing A Chair Back 1 Unit Assembly Instructions: B Chair Seat 1 Unit STOP Tools Needed: Philips Head Screwdriver Please read all instructions before assembly. Step 1: Insert Casters (D) into Base (H). A STOP If you are assembling a model with a DK Foot Ring please proceed to subsequent pages for drafting kit assembly instructions. Step 2: Insert Gas Lift (E) into Base (H).
PAGE 2
Model AA-3 Adjustable Arms Parts Listing A AA-3 Adjustable Armrest 2 Units Assembly Instructions Height Adjustment Button A B M6x30mm Screw 6 Units STOP Tools Needed: Phillips Head Screwdriver Please read all instructions before assembly. Step 1: Turn Chair Seat upside down and place on a clean, non-abrasive surface. Step 2: Align the pre-drilled holes in the Adjustable Armrest (A) with the holes in the bottom of the Chair Seat, making sure that the arms face the correct direction.
PAGE 3
Model DK-2 Drafting Kit Assembly Parts Listing A Circular Foot Rest 1 Unit Assembly Instructions STOP Chair Seat Please read all instructions before assembly. Prior to assembly, select only one Extension Tube for desired Height 9” Extension Tube will change seat height from 24”-28” 12” Extension Tube will change seat height from 27-31” Step 1: Slide the Circular Foot Rest (A) over the smaller tapered end of your chosen Extension Tube (C / D).