User guide

ManualsBrandsOFNA Racing ManualsHardware91849 DigiPeak 3

FEATURES:

1.Super function3 in 1 16 bits microchip CPU controller

2. AC, DC are both compatible

AC 110V or 230V switching power supply technologyinput DC 11V ~ 18V input usable

3. Two-line 16 characters dot matrix large LCD display

4. AC & DC's plug socketsare removable

5. Universal output terminal

6. Deactivate and reactivatethe beeper by using the "select" button

7. Detect inversion of the battery automaticallyand input reverse protection

8. Built-ina DC cooling fan

9. Entire aluminumcasing design - compactand portable

SPECFICATION:

Input : AC 110V OR 230V / DC 11~18V

Battery Type : Ni-Cd / Ni-MH / Li-Po

Battery Cell : Ni-Cd/Ni-MH1 - 14 Cell (1.2V - 16.8V)

Li-Po 1 - 4 Cell (3.7V - 14.8V)

Charge Rate : 0.3A ~ 5A (0.1A

increments

)

Discharge Rate : 2A (Constant current)

Peak Detection

(AUTO SENSING)

NiCd 1-14 cells

Ni-Mh 1-14 cells

Li-Po 1-4 cells

DIGIPEAK

-3

AC/DC CHARGER

CHARGES Ni-Cd or Ni-Mh or Li-Po

1-14 Cell

5 Amp

Summary of content (7 pages)

PAGE 1
DIGIPEAK-3 AC/DC CHARGER CHARGES Ni-Cd or Ni-Mh or Li-Po 1-14 Cell 5 Amp Peak Detection (AUTO SENSING) NiCd 1-14 cells Ni-Mh 1-14 cells Li-Po 1-4 cells SPECFICATION: FEATURES: 1.Super function 3 in 1 16 bits microchip CPU controller 2. AC, DC are both compatible AC 110V or 230V switching power supply technologyinput DC 11V ~ 18V input usabl e 3. Two-line 16 characters dot matrix large LCD display 4. AC & DC's plug sockets are removable 5. Universal output terminal 6.
PAGE 2
Charge Mode A B (ENTER) into charge mode. 1.MAIN MENU -> press the 2.Set the current rate before charging. Adjustable charge rates from 300mA-5000mA. The default current is 2A, you can use the +(INCREASE) and -(DECREASE) button to adjust the charge rate. C See the table below to select the charge rate for Ni-Cd & Ni-MH battery packs. We recommend that you charge 1800mAh receiver packs at 1.8 amp. (1C). Battery Capacity Charge Rate 600mAH 1300mAH 3300mAH Charge Time 0.6A 60 ~ 80 Min. 1A 78 ~ 94 Min.
PAGE 3
Operation Instr uction Operation Signal Function Button INCREASE + DECREASE ENTER S START ' FLASH ' A Plug the charger into an AC 110V/230V wall outlet or a DC 12V power source. The charger power is on now and the LCD displays the MAIN MENU. 1 2 NI-CD CHARGE C=2.OA 3 1:Battery type 3:Charge current 4 B The LCD displays the data below.
PAGE 4
In Ni-Cd or Ni-MH mode Discharging Process Charging Process NI-CD CHARGE C=2.0A NI-CD 'CHARGE' C=2.0A + - NI-CD CHARGE C='2.0A' NI-CD 'DISCHARGE' D=0.5A END=6.0V NI-CD DISCHARGE D='0.5A' END=6.0V Set the CHARGE current - + - + - NI-CD CHARGE C='5.0A' + NI-CD DISCHARGE D='2.0A' END=6.0V MIN. DISCHARGE current is 0.3A MAX. DISCHARGE current is 2A MIN. CHARGE current is 0.3A MAX. CHARGE current is 5A NI-CD CHARGE C=2.0A NI-CD DISCHARGE D=2.0A END='6.0V' S - + NI-CD DISCHARGE D=2.
PAGE 5
In Li-Po mode Discharging Process Charging Process LI-PO CHARGE C=2.0A 7.4V LI-PO 'CHARGE' C=2.0A 7.4V LI-PO CHARGE C='2.0A' 7.4V + - LI-PO CHARGE C='4.0A' 7.4V MIN. CHARGE current is 0.3A MAX. CHARGE current is 4A LI-PO CHARGE C=2.0A '3.7V' 1 CELL - + LI-PO CHARGE C=2.0A '7.4V' 2 CELL - + LI-PO CHARGE C=2.0A '11.1V' 3 CELL + - LI-PO CHARGE C=2.0A '14.8V' + + - LI-PO 'DISCHARGE' D=0.5A END=6.0V LI-PO DISCHARGE D='0.5A' END=6.0V - + LI-PO DISCHARGE D='2.0A' END=6.0V MIN.
PAGE 6
Beep Setup TONE ENABLE TONE 'ENABLE' + TONE 'DISABLE' TONE ENABLE TONE DISABLE TONE ON TONE OFF Error Message LCD Display Problem [Error] REVERSE POLARITY The output terminal is connected inversely to the polarity of the battery pack. [Error] OUTPUT SHORT Short circuit protection for the output terminal. [Error] OPEN CIRCUIT The battery pack is not connected to the charger before charging. 1.Battery pack fail. 2.Battery pack disconnect charger.
PAGE 7
Safety Precautions : 1.Please check the voltage in your house if it's consistent to this charger, you can only use it when the voltages are the same. 2.Do not allow children to charge battery packs unless supervised by a responsible adult. 3.Use only rechargeable batteries. This charger cannot charge primary batteries such as "Heavy duty", "Alkaline battery" or "Mercury battery". 4.During use, please keep in a well ventilated area and never put beside flammables chemicals. 5.