Strong Front and Rear chassis braces. Tuned Polished Dual Chamber racing pipe. INSTRUCTION Unique adjustable chassis width of 310mm or 330mm. High performance .26 engine with Shaft Start Motor handle. Full race Offset King Pin aluminum steering knuckle. Three sealed differentials with 6 steel gears. Racing Stadium and Truck tire sets. Adjustable Front and Rear roll bars. Multi disc brakes with adjustable bias. Hard Coated Threaded body oil fill shocks. 5 Degree hard coated 3mm chassis.
RTR KITS - REQUIRED FOR OPERATION THINGS NEEDED You will need to buy a few items to start the engine and run the car. • Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will over heat engine. • Buy LONG glow plugs, like OFNA/PICCO Plug (#51007 or 51008). Use plugs without idle bar. Do NOT use plugs, like the MC-59 or OS-8 In your box you will find..
MUST READ THIS BEFORE RUNNING Running a nitro kit is fun and easy, but to make this a safe and good experience you must observe a few rules. This kit is extremely fast, easily over 40MPH, and can seriously injure someone if you are not careful. Where to run car? • Any running area you choose must be dry. Do not run car near any water or wet dirt. • Do not run on public streets. It is very easy to have the car run over or damaged by hitting the curb. • Do not operate car in tight confined places.
Builds two differentials for front and rear. ASSEMBLE OF THE DIFFERENTIAL FOR FRONT AND REAR Step 1 40010 2.5x13.8mm Pin 40006 Cap Joint Step 2 OPT : JS-01 CNC Steel Diff. Gear Set 94034 4x4mm Set Screw 40010 2.5x13.8mm Pin 40009 P6 O-Ring 40004 Diff. Gear (Large) 36053 8x16mm Ball bearing 40012 6x18mm Washer 40003 Diff. Case 40010 ..........X2 2.5x13.8mm Pin 40009 P6 O-Ring Step 3 30779 4x10mm 40004 Washer 30773 Diff. Gear 4mm (Small) Cross Pin 40004 Diff. Gear (Small) 40009 P6 O-Ring .......
ASSEMBLY OF THE FRONT GEAR BOX Insert two ball bearings as shown. 40017 Gear Box 36053 8X16mm Ball bearing Adjust the backlash with the shims. 40024 13x16x0.2mm Shim 36053 8X16mm Ball bearing 40017 Gear Box 49012 Small Bevel Gear 94011 4x16mm Hex Screw 94011 4x16mm Hex Screw ..........X2 40024 13x16x0.2mm Shim 40024 13x16x0.2mm Shim 94011 4x16mm Hex Screw ..........
ASSEMBLY OF THE FRONT SHOCK STAY 40116 Shock Tower 94010 4x12mm Hex Screw 94010 3x12mm Hex Screw 94010 4x12mm Hex Screw ..........X2 94004 3x12mm Hex Screw 94010 4x12mm Hex Screw ..........
ASSEMBLY OF THE FRONT SUSPENSION ARMS Assembly of the right and left hand side are the same. Step 1 90021 E-Ring 90021 E-Ring Step 2 ASSEMBLY OF THE FRONT LOWER ARMS 40023 Lower Arm Shaft (4mm) Insert the rear drive shaft into cap joint before assembly the rear lower arm. ASSEMBLY OF THE FRONT KNUCKLE ARMS Step 3 40104 4x16mm Cap Screw 90020 2.5mm E-Ring 40104 4x16mm Cap Screw 90021 3mm E-Ring 90020 2.5mm E-Ring 40104 4x16mm Cap Screw ..........X4 90020 2.5mm E-Ring ..........
ASSEMBLY OF THE FRONT STABILIZER Assembly of the right and left hand side are the same. 40029 Stabilizer Ball End Step 1 40290 3x10mm Hex Screw ..........X4 94005 3x16mm Hex Screw ..........X2 30341 Stabilizer Ball 94035 3x8mm Set Screw ..........X2 94035 M3x8mm Set Screw 94033 M3x3 Set Screw 40199 Stabilizer Ball End ..........
ASSEMBLY OF THE REAR GEAR BOX Insert two ball bearings as shown. 40017 Gear Box 36053 8X16mm Ball bearing 40024 13x16x0.2mm Shim 36053 8X16mm Ball bearing 94011 4x15mm Hex Screw ..........X2 Adjust the backlash with the shims. 40017 Gear Box 49012 Small Bevel Gear 94011 4x15mm Hex Screw 40024 13x16x0.2mm Shim 40024 13x16x0.2mm Shim ..........
ASSEMBLY OF THE REAR SHOCK STAY Assembly of the right and left hand side are the same. 40116 Shock Tower 94010 4x12mm Hex Screw 94010 4x12mm Hex Screw 94004 3x12mm Hex Screw ..........X2 94004 3x12mm Hex Screw ..........X2 ASSEMBLY OF THE UPPER ARM ROD Assembly of the right and left hand side are the same. * Builds two upper arms for left and right hand-side. 40065 Upper arm Plastic Rod End 36860 5x60mm Turnbuckle * Anticlockwise mark.
ASSEMBLY OF THE REAR SUSPENSION ARMS Assembly of the right and left hand side are the same. Step 1 90021 3.0mm E-Ring 40023 4mm Lower Arm Shaft 90021 3.0mm E-Ring Step 2 90020 2.5mm E-Ring 90020 2.5mm E-Ring 40102 3mm Plastic Washer 40102 3mm Plastic Washer Step 3 90021 3mm E-Ring 90020 2.5mm E-Ring 35313 M3 Nylon Nut 36170 3mm Arm Shaft 35313 Nylon Nut ..........X4 ..........X2 ..........X2 *Insert the rear drive shaft before assembly.
ASSEMBLY OF THE REAR STABILIZER Assembly of the right and left hand side are the same. Step 1 40290 3x10mm Hex Screw 94005 3x16mm Hex Screw 40029 Stabilizer Ball End ..........X4 30341 Stabilizer Ball ..........X2 94035 3x8mm Set Screw 94035 M3x8mm Set Screw ..........X2 94033 M3x3 Set Screw ..........
ASSEMBLY OF THE SERVO SAVER Step 2 Step 1 40035 Servo Saver Alum. Tube 40031 Plastic Bushing 40037 Steering Plat Hex Screw 94009 4x10mm Hex Screw 40031 4x8mm Plastic flange Bushing 40037 Steering Plat Hex Screw 40031 Servo Saver Horn A 40095 Servo Saver Connecting Plate 40031 4x8mm Plastic flange Bushing 35313 M3 Nut * Put the 3mm nut before assembly.
ASSEMBLY OF THE BRAKE AND CENTER DIFF. MOUNT A 36661 Brake Pad Linings Remove the double-side tape before assembly. B C G-06A Brake Pad Linings 36660 Brake Pad Step 1 40045 Brake Pad Adjustment Screw Step 2 40040 Center Diff. Mount 40044 Brake Pad Spring 40044 Brake Pad Spring C C B B A A 40044 Brake Pad Spring 40044 Brake Pad Spring 40045 Brake Pad Adjustment Screw 40040 Center Diff. Mount Step 3 Step 4 40040 Center Diff. Mount 40040 Center Diff. Mount 40043 Center Diff.
ASSEMBLY OF THE CENTER DIFF. INTO CENTER DIFF. MOUNT Step 1 Step 2 Step 3 94033 3x3mm Set Screw 94003 3x10mm Hex Screw 40096 Center Diff. Plate 30211 Plastic Bushing 30211 Plastic Bushing 30171 Brake Lever 30213 Brake Cam 30213 Brake Cam 94003 3x10mm Hex Screw Step 4 94033 3x3mm Set Screw Step 5 40031 Fuel Proov Plate 30171 Brake Lever 94003 3x10mm Hex Screw 94033 3x3mm Set Screw ..........X4 ..........X2 ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS Insert drive shaft into cap joint.
ASSEMBLY OF THE CENTER STIFFENER ONTO CHASSIS 90018 3x25mm Cap Screw 40018 Center Chassis Brace ( Front ) 35313 3mm Nylon Nut 40018 Center Chassis Brace ( Rear ) 94004 3x12mm Hex Screw 35313 M3 Nylon Nut 94004 3x12mm Hex Screw 94027 4x16mm Flat Head Hex Screw 90018 3X25mm Cap Screw ..........X1 ..........X1 94027 4x16mm Flat Head Hex Screw ..........X4 94027 4x16mm Flat Head Hex Screw ..........
ASSEMBLY OF THE RADIO TRAY Step 1 49039 Alum. Radio Tray 94003 3x10mm Hex Screw Step 2 40027 Radio Tray Post ( Plastic ) 94003 3x10mm Hex Screw 94003 3x10mm Hex Screw Throttle Servo 40027 Radio Tray Post ( Plastic ) 40027 Radio Tray Post ( Plastic ) 94003 3x10mm Hex Screw 94003 3x10mm Hex Screw 94003 3x10mm Hex Screw Steering Servo Step 3 94004 3X12mm Hex Screw 10274 Servo Post 10274 Servo Post *Connect as per radio.
ASSEMBLY OF THE RADIO TRAY ONTO CHASSIS 94019 3x10mm Flat Head Hex Screw 94019 3x10mm Flat Head Hex Screw ..........X2 94019 3x10mm Flat Head Hex Screw 94019 3x10mm Flat Head Hex Screw ASSEMBLY OF THE SHOCKS * Builds 4 for Shocks. Step 1 Step 2 32237 40076 Shock body Fit the o-ring into groove before assembly. 32237 3.5mm O-Ring 32237 3.5mm 32237 O-Ring 2mm Washer 40059 13.8mm O-Ring 2.6x5mm Washer 32237 3.
ASSEMBLY THE DUST COVER AND SHOCK SPRING Step 1 40089 Shock Spring (Black) Step 2 30411 6mm Ball 40058 Shock Shaft Dust Cover Push 6mm ball joint into ball end. 40063 Spring Holder ASSEMBLY OF THE FRONT SHOCK ABSORBERS Assembly of the right and left hand side are the same. 90018 3X25mm Screw Take the plastic bushing from the shock plastic parts tree. 40056 Plastic Bushing 35313 M3 Nylon Nut 35313 M3 Nylon Nut 30702 3X20mm Cap Screw 90018 3X25mm Cap Screw 36610 Shock Upper Fixing ..........
ASSEMBLY OF THE BODY POST 40117 Body Support Plastic 2.6x15mm Screw 94004 3x12mm Hex Screw 94010 4x12mm Hex Screw 40117 Body Post Plastic 94042 M4 Nylon Nut 2.6x15mm Screw 40117 Body 94010 4x12mm Hex Screw 35313 M3 Nylon Nut 40117 Body 94012 4x20mm Hex Screw (FRONT) 94010 4x12mm Hex Screw 35313 M3 Nylon Nut 94042 M4 Nylon Nut 2.6x15mm Screw 94004 3x12mm Hex Screw 94010 4x12mm Hex Screw 94012 4x20mm Hex Screw ..........X2 94004 3x12mm Hex Screw 35313 M3 Nylon Nut ..........X2 ..........
ASSEMBLY OF THE FUEL TANK Step 1 Step 2 Pressure Nipple 94005 3x15mm Hex Screw 94005 3x15mm Hex Screw Pressure Nipple 40109 Fuel Tank 40047 Fuel Tank Post 94005 3x15mm Hex Screw 40047 Fuel Tank Post * Take the fuel tank post from J-42 plastic parts tree. ..........X2 94019 3x10mm Flat Head Hex Screw 94019 3x10mm Flat Head Hex Screw ..........X2 ASSEMBLY OF THE CLUTCH Step 1 10091 Pilot Shaft Place the clutch shoes with the clutch springs over the 3 pins of the flywheel.
ASSEMBLY OF THE CLUTCH INTO ENGINE 3 x 5mm Screw Notes: Non-Pull Start Engines... • Alum. Washer behind the flywheel is not needed when using Force engines or similar types. O.S. Engines will require washer spacer. 10099 3 X 8mm Washer 3 x 20mm Cap Screw • To check!..place the brass corn against the engine bearing, then flywheel. You should be covering one or two thread of the engine shaft. If this is the case, you do not need an additional washer behind the flywheel.
ASSEMBLY OF THE MANIFOLD AND MUFFLER Step 1 Step 2 10068 Manifold Adapter 10120 Manifold Spring 10060 Manifold Nylon Straps (Middle) Option: 10182 Silicone Tube, Red 10183 Silicone Tube, Yel. 10184 Silicone Tube, Blue 10184 Silcone Tube 31992 Pipe ASSEMBLY OF THE ENGINE ONTO CHASSIS Spur Gear Clutch Bell 90 degree Use note book paper to set gear backlash between spur gear and clutch bell gear. If the space is not correct the spur gear will be damaged.
ASSEMBLY OF THE FUEL TUBE Step 1 Step 2 Connect to fuel nipple. 10179 Fuel Tube Connect to fuel tank pressure nipple. Connect to carbulater. 10179 Fuel Tube Connect to pressure nipple. ASSEMBLY OF THE BUMPER 40204 Front Bumper 94004 3x12mm Screw 94004 3x12mm Screw 94028 4x20mm Flat Head Hex Screw ..........X1 ..........
ASSEMBLY OF THE FRONT STEERING ROD 94004 Step 1 Step 2 3X12mm Hex Screw 10768 Servo Horn 30410 6mm Ball 94004 3X12mm Hex Screw #312 Servo Horn Adapter 30410 Plastic Ball End Use the screw provided with your servo. 30410 Plastic Ball End 30690 3x30mm Tie Rod 30410 6mm Ball Parallel 94004 3X12mm Hex Screw Align the steering servo as shown. ..........
ASSEMBLY OF THE BRAKE LINKAGE INTO BRAKE LEAVE 3x3mm Set Screw USING BREAK ADJUST NUT #158 Alum Stopper Tighten or loose the adjuster nut will change the brake. 3x3mm Set Screw Loose Tighten More Brake Less Brake use the screw provided With your radio. 3x3mm Set Screw ..........
ASSEMBLY OF THE TIRES AND WHEELS Step 1 Step 2 86070 Stadium Tires Apply instant glue into the groove of the wheel. IN S G TA L N U T E B-21 Inner Sponge 86069 Stadium Wheel ASSEMBLY OF THE TIRE ONTO FRONT KNUCKLE AND REAR HUB 15072 Blue Wheel Nut Tire and Wheel assembly. 15072 Blue Wheel Nut Tire and Wheel assembly. Assembly of the right and left hand side are the same.
ASSEMBLY OF THE TIRES AND WHEELS Step 1 Step 2 Right - side Left - side Notice the direction of the tyres. Notice the direction of the tyres. 86101 Truck Wheel B-25 Truck Inner Sponge 86100 Truck Tire. LZ Thread 86100 Truck Tire. LZ Thread B-25 Truck Inner Sponge 86101 Truck Wheel IN S G TA L N U T E Apply instant glue into the groove of the wheel. ASSEMBLY OF THE TIRE ONTO FRONT KNUCKLE AND REAR HUB Tire and Wheel assembly. 15072 Blue Wheel Nut 15072 Blue Wheel Nut Tire and Wheel assembly.
SETTING GUIDE FRONT CAMBER ANGLE SETTING + Positive - - REAR CAMBER ANGLE SETTING + - - + Negative + Negative Positive Turnbuckle Turnbuckle Place the model car on flat surface. Raise the chassis to it's maximum clearance before the wheels leave the ground. Adjust the length of the front and rear upper arms so that the wheels are right angle to the ground. The camber angle adjustment can be moving the turnbuckle rod on the upper arms, clockwise or anti-clockwise.
APPENDIX PAGES
SHAFT START NOTICE: 9.5 BLAZER RTR KITS WILL COME WITH “SHAFT START #50000” (same as Rotor Start). THEREFORE, A PULL START ENGINE IS NOT USED AND THE SHAFT START FORCE BACK PLATE (#50010) IS ALREADY INSTALLED. BEFORE YOU CAN USE THE SHAFT START MOTOR HANDLE, YOU MUST FIRST GET OR BUY A STANDARD 7.2 BATTERY PACK. AFTER POWERING UP THE MOTOR HANDLE, INSERT THE SPECIAL DOG BONE SHAFT AND TURN OVER THE ENGINE.
TUNING AFTER BREAK-IN Close master needle by turning clockwise until it stops. Then open needle by turning counterclockwise 3 turns (rich setting). When running car, adjust carb with 1/8 clockwise turns, slowly leaner, until the top speed good. Check engine temp, if possible, for no more 250 degrees. Adjust low end needle for best throttle response. Use only small turns. From idle, give it full throttle, if throttle is slow lean out needle until good.
OFNA MICRO FAIL SAFE UNIT - #91002 (MICRO) The OFNA Fail Safe unit is used to protect your RC car from loss of control due to: • Weak radio signal • Low radio batteries • Radio interference of any kind • Another radio on the same channel • Low receiver car battery • Fits most if not all U.S. RC radio’s The Fuzzy logic CPU operates on 3.8 to 6.0 volts DC from your receiver battery pack.
BLAZER SST RTR ( 9.
40025 40028 40029 40030 40031 40032 40033 40034 40035 40036 40037 40038 40039 40040 40041 40042 40043 40044 40045 40047 40048 40049 40050 40051 40053 40055 40056 40057 40058 40059 40060 40063 40064 40065 40068 40069 40070 40071 40072 40073 40074 40075 40077 40088 40089 40090 40093 40101 40102 40103 40104 40105 40106 40107 40108 40109 40116 40117 40204 40206 40898 49012 49016 49032 86069 86070 86100 86101 90021 90026 REAR, LOWER ARM ALUM.
OWNER’S REGISTRATION CARD OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment. The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date.