/12 ELECTRIC POWERED MINI TRUGGY OFNA RACING WWW.OFNA.COM 7 VANDERBILT IRVINE, CA 92618 ADDITIONAL PARTS NEEDED * Batteries 8 AA for Radio * Receiver Batteries * Model Fuel 20% Nitro THIS IS NOT A TOY ! This kit is extremely fast, and can easily go over 40mph and can seriously injured someone. If you are under 18years of age have and adult supervision.
Hyper Engine SERIES M3x35mm Screw
Assembly of Front/Rear Differential 1 11066 10x15mm Ball bearing 1 x2 02 1 3 1 2 21003x2 2x11.8mm Shaft 21006 F/R Diff drive shaft 11066 ball bearing 21003x2 4x26.9mm Shaft 3 21003x2 6x8mm O-ring 21003 Small bevel gear 21004 Diff. Case 21003 Large bevel gear 21004x1 Seal * Sillcone oil (hard) 2 21003x2 6x12mm Washer 21001 Crow gear 21003x4 M2.6x10 F/H screw *Put silicon oil (hard) included in the package Assembly of CenterDifferential 1 11066 10x15mm Ball bearing 21003x2 2x11.
Assembly of Front/Rear Differential 94034 M4x4mm Set screw 03 T 3 L x2 21005x2 Center join cup 21002x1 Drive pinion gear 21007 Gear box 21007 Gear box 11065 5x11mm Ball bearing Assembly of Front Suspension step-1 21015x4 Pillow ball 4 21014 Lx1,RX1 LR 21014x4 21014 M3x8mm Screw 22012x2 5.
Assembly of Front Suspension step-3 11066 10x15mm ball bearing 04 6 LR 21017 x4 2x10.8mm Shaft 18075 6x13mm ball bearing 3.
Assembly of Front Tower 05 9 21008 Front shock stay 21008 M3x12mm TP screw Assembly of Front body post 10 21008 M3x15mm TP screw 21030 Front body post Assembly of Front Stabilizer step-1 21018x4 5.
Assembly of Front Stabilizer step-2 06 12 2 T L T L 21018 x2 M3x3mm Set screw 21005 x2 M4x6mm Set screw 1 21018 21005 x2 M3x12mm Screw 21019 Bumper set Assembly of Front upper arms 21028 x2 3x35mm Shaft 21029 Plastic shaft gasket 21029 Plastic washer 2mm 13 LR 21011 Front upper arm LX1,RX1 3.2mm Assembly of Steering servo saver Arms 21033 Alu.nut 21033 3x8mm Washer 14 21034 Servo saver arm 22012x2 Ball T 94041 Nut 11064 5x8mm Ball bearing 21033 Servo saver spring 21033 Alu.
Assembly of Steering Rod 07 15 21033 X2 M3x3mm Set screw 21033 X2 Stopper 21033 Assembly of Front upper arm holder 16 21013 21033 M3x8mm Screw 21033 M3x10mm Screw Assembly of Steering Rod 21036 x6 Turnbuckle rod end 17 x2 21023 x2 Turnbuckle rod 3.
Assembly of Front Bumper & Front Brace 08 8 18 94002x4 M3x8mm Screw 21019 Front bumper Assembly of Front Diff & Suspension arms onto Chassis 19 94020x4 M3x12mm F/H screw 21058 Front brace set Assembly of Rear Suspension arms 20 21026 Rear join cup 21025 Rx1,Lx1 LR 21017 x4 2x10.
Assembly of Rear Suspension arms-1 09 21 21010x1 Alu. lower arms holder LR 21010 M3x12mm Screw 21028 x4 3x51mm Shaft 21029 Plastic washer 3mm 21024 Rx1,Lx1 Rear lower arm 21029 Plastic shaft gasket Assembly of Rear Suspension arms-2 21029 Plastic shaft gasket 22 21021 M3x35mm Screw 21021x1 Rear lower arms holder-alum Assembly of Rear Shock Stay 23 T L 21020 Rear shock stay 22012x2 5.
Assembly of Front/Rear Differential 10 24 21023 x2 M3x12mm Screw T L 94041 x2 M3 Nut T L Assembly of Rear Upper Arms 25 x2 19.00mm 21035 x2 M3x36.
Assembly of Front Stabilizer step-1 21018 x4 5.
Assembly of Rear Upper Arm Holder 30 21031 94002 M3x8mm Screw Assembly of Wing Stay 31 M3x15mm Screw Assembly of Rear Brace 94033 M3x3mm Set screw 32 Stopper C-clips 21058 Rear brace set 21032 x1 Shaft 12
Assembly of Front Bumper onto Chassis 13 33 21061 Standard Chassis 94020 M3x12mm F/H screw 21019 Rear bumper Assembly of Center Gear Box step-1 19052 M3x12mm Hex head screw 21039x2 Center diff mount 34 28087x2 Brack caliper 21040 x2 Brake disc 21039 Consolidate plate Assembly of Center Gear Box step-2 21041 x2 Brake rod 35 21042 Center alum diff plate 21041 x2 Brake cam 94004 M3x12mm Screw 21039X2 94033 x2 M3x3 Set screw 21039 Center diff mount
Assembly of Center Diff Mount onto Chassis 14 14 21043 Center top alu.plate 94019 M3x10mm F/H screw 36 Assembly of Center Gear Box onto Chassis 21060 80mm Center Drive shaft 94020 M3x12mm F/H screw 21060 50mm Center Drive shaft 37 Assembly of Engine mount M3x10mm Cap screw T 38 L 28061x1 M3x10mm Collar 10097x2 M3x10mm Pilot nut 28061 2.5x16.
Assembly of Clutch-Step-1 15 39 10010 x3 Clutch shoe Notice the clutch spring 10102 x3 Clutch spring 2 1 Assembly of Clutch-Step-2 10099x1 M3x8mm Cap screw 40 10099x1 3.1x6mm Washer 10099 x2 5x8mm Washer 18077x2 5x10mm Bearing 21055 x1 Clutch bell-14T T L Assembly of Engine onto Chassis 21054 x2 M3x8mm F/H screw 21054 x2 M3x6mm F/H screw *The fitting is in good position if there is a clear gear-teething mark on the paper after sliding out. 21054 x4 M3 ALU.
Assembly of Fuel Tank 10170 x1 M3x10mm TP screw 16 21044 42 10170 x1 M3x12mm Screw 21044 10170 x1 Fuel filter 21045 Fuel tank set 21044 Fuel tank post 21044 Fuel tank post Assembly of Fuel Tank onto Chassis 43 94019 x1 M3x10mm F/H screw Assembly of Manifold 21057 Manifold 44 21057 x2 Silicone tube 21057 x3 S.
Assembly of Manifold and Mufflerntial 94034 x3 M4x4mm Set screw 45 21056 x3 M4x8mm Set screw 21085x1 Muffer stay T L 21085 x1 Muffer holder Assembly of Manifold spring 46 21056 L.
Assembly of Throttle Linkage into Lever 94033 M3X3mm Set screw Stopper 48 18 21049 Servo horn 21049 Collar 11281 x1 Nut 21049 Collar 11281 x3 Throttle spring 21049 Collar 21050 Throttle ball end 22012x4 Ball end 21056 x3 M2.5x6mm Screw 21056 x3 M3x8mm Screw 21050 Throttle ball end 21056 x3 M3x20mm Screw 11281 x3 Throttle rod Equipmentl 22012x4 Ball end 49 21056 x3 M2.
Assembly of Receiver box 19 21046 51 21046 21046 x3 M3x5mm F/H screw 21046 x3 M3x10mm TP screw 21046 21046 Receiver box Assembly of Receiver box 52 28081 28081 x1 3~5mm THROTTLE SERVO STEERING SERVO ON/OFF SWITCH
Assembly of Radio Tray and Receiver box onto Chassis 20 53 21056 x3 M3x8mm F/H screw Assembly of Air Filter 54 21053 Air filter foam cover 21053 Air filter 21056 x3 M3x10mm F/H tapping screw 21052 Air filter Zip Tie 21051 Rubber tube 21052 Air filter Assembly of CenterDifferential 21056 x3 M3x10mm TP screw 55
Assembly of Front/Rear Differential 21 56 11mm 21048 x1 Ball end 21048 x1 M4x20mm Servo linkage Assembly of Front Shocks-Step-1 21068x4 2.6x6.5x0.6mm washer 21068 x4 Shock collar 57 21068 Shock piston 21064 Front shock body 21062 Front shock shaft 22028 x8 O-ring Fit into groove. 22028 x4 C-clip 21062 x6 C-clip 21068 Assembly of Rear Shocks-Step-2 21068 x4 2.6x6.5x0.
Assembly of Front and Rear Shock-Step-3 21063 x4 Shock Bladder 22 59 NO Bubbles S c ho kO SHORT FOR FRONT X2 il 1 21067 x4 Shock ball head LONG FOR REAR X2 21067 x4 Shock pro cap 2 1 2 21066 x4 Alu shock adjustable ring Pull down the pistion. Move the shaft up and down slowly to remove bubbles.
Assembly of the Front Shock Absorber 19031x4 Steel shock ball 23 62 LR T L 21048 x1 Steel shock ball 21048 x1 M3x12mm Cap screw Assembly of the Rear Shock Absorber 63 LR 21048 x1 M3x15mm Screw Assembly of Wheels and Tyres 21075 Tire 64 x4 21076 Linner Sponge Glu 21082 Wheel e
Assembly of the Tyres onto Front Knuckles 24 10985 x10 Nylon nut 4mm 65 LR Assembly of the Tyres onto Rear Hubs 66 LR 10985 x10 Nylon nut 4mm Assembly of the Wing 67 21071x2 M3x15mm Cap screw 21071 21071x2 Wing washer
Assembly of the Tyres onto Front Knuckles 68 21080 Body shell Assembly of the Wing 69 21073 Snap pin 25
21301 21302 21303 21304 21305 21306 21307 21308 29076 21308 21308 VELCRO 21308 21302 21308 21308 21308 21308 21306 21308 21308 21308 PART # 14612 21305 29076 21308 OPTIONS PARTS 21304 21307
Name: Date: Track: Length: Front width: Engine Rear width: Wheelbase: Height: Diff.Oil Clutchbell Type: Front: 13T Gasket: Center: Spur gear Plug: Rear: Fuel: Front Arms: 3.2m 14T 42T Weight: other: other: Steering Rod: m 29 . 8m m 3.2mm Camber Deg. Front Toe angle: Deg. - + + Length: - Front Shock: Rebound Stop Ride Height Rear Front Upper Arms: Steering Servo Rod: 1 9 .0 0m m 11. 0 0mm Rear Toe angle: Camber Deg. - - + + Deg.
BLANK
Name: Date: Track: Length: Front width: Engine Rear width: Wheelbase: Height: Diff.Oil Clutchbell Type: Front: 13T Gasket: Center: Spur gear Plug: Rear: Fuel: Front Arms: 3.2m 14T 42T Weight: other: other: Steering Rod: m 29 . 8m m 3 .2 m m Camber Front Suspension: Deg. Front Toe angle: Deg. - Front Shock: + Rebound Stop Ride Height Rear Front Upper Arms: Steering Servo Rod: 1 9 .0 0m m 11. 0 0mm Rear Toe angle: Camber Deg. - - + + Deg.
BLANK
hyper mini electric/gas parts list OFNA 10177 10282 10097 10170 11065 11066 11210 18075 18077 19018 19031 21001 21002 21003 21004 21005 21006 21007 21008 21009 21010 21011 21012 21013 21014 21015 21016 21017 21018 21019 21020 21021 21022 21023 21024 21025 21026 21027 21028 21029 21030 21031 21032 21033 21034 21035 21036 21037 21038 21039 21040 21041 21042 21043 21044 21045 21046 21047 21048 DESCRIPTION FUEL LINE 3FT.
OWNER’S REGISTRATION CARD OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment. The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date.