REV.
IMPORTANT-READ THIS BEFORE RUNNING Running nitro kit is fun and easy, but to make this a safe and good experience you must observe a few rules. This kit is extremely fast, easily over 65KPH, and can seriously injure someone if you are not careful. 5. Emer gency Engine Stopping Remove air filter and cover carb. intake. Squeeze fuel line and hold until engine stops. With a rag, cover exhaust outlet. 1. W here to r un car? Any running area you choose must be dry. Do not run car near any water or wet dirt.
REQUIRED FOR OPERATION THINGS NEED BESIDES THE KIT OFNA/Picco JL Racing .12 Red Dot Parts # 51124 Glow Plug Long Heat with Battery & Charger # 10215....$27.
PLASTIC PARTS FOR USE 40833 RECEIVER BOX 40836 FRONT AND REAR LOWER ARM 40834 SERVO SAVER 40839 FRONT C HUB 40835 DIFF.
PLASTIC PARTS FOR USE 30802 THROTTLE LINKAGE PLASTIC 40842 WING STAY & BUMPER 40841 FRONT KNUCKLEARM 40843 REAR UPRIGHT 40844 CENTER DIFF.
1 ASSEMBLY OF THE CENTER DIFF. Tighten Step 1 30779 4x10mm Washer 2.6x10mm Step 2 30773 40805 30779 .....x8 Tight the diff screws in this order. 94046 2.6x10mm Flat Head Screw 40011 1 3 4 2 .....x4 30773 4mm Cross Pin Dif f . Oil .....x2 Use 1000 weight diff. oil in the center. Fill the Diff. Case to approx. 80% with the Diff.Oil. 2 ASSEMBLY OF THE FRONT GEAR CASE Step 1 94034 4x4mm Set Screw Step 2 w t r e en Sc em C 4x4mm .....x1 40840 40806 37430 5x11mm Ball Bearing Apply Grease ..
4 ASSEMBLY OF THE FRONT LOWER ARMS * A 3x8mm set screw is used to adjust ride-height. 3x8mm Ensure Free Movement 3x8mm 94035 3x8mm Set Screw * Notice the direction of the front lower arm holder in rear. .....x1 40836 40837 Up 94004 3x12mm Hex Screw .....x2 1:1 1:1 40825 40837 Ensure Free Movement 40813 3x12mm 40825 40836 1:1 5 ASSEMBLY OF THE FRONT UPPER ARMS 1:1 *Approx. 8.
7 ASSEMBLY OF THE FRONT SUSPENSION ARMS 94001 3x4mm Hex Screw .....x2 94005 3x15mm Hex Screw .....x2 Assembly for both right and left side. Ensure Free Movement 3x4mm 40823 3x15mm 8 ASSEMBLY OF THE FRONT STABILIZER 94035 3x8mm Set Screw Assembly for both right and left side. .....x2 30403 6mm Ball Makes two rods for left and right hand-side. .....x2 40848 94005 3x15mm Hex Screw .....
10 ASSEMBLY OF THE SERVO SAVER 40810 Step 2 Step 1 Ensure Free Movement Step 2 40811 40834 37220 King Pin Bushing 40834 .....x2 94002 3x8mm Hex Screw 40834 .....x2 37360 37360 Servo saver spring preload setting. *Approx. 0.5mm 37220 37220 3x8mm 3x8mm 40809 37360 Do Not Over Tighten 11 ASSEMBLY OF THE SERVO SAVER AND THE STEERING TIE-ROD Screw Cement 3x8mm 3x8mm Step 1 94002 3x8mm Hex Screw Screw Cement Step 2 40834 .....x3 3x8mm 3x8mm 35958 94040 3x8mm Washer 35958 .....
13 ASSEMBLY OF THE REAR GEAR CASE 3x10mm w t re en Sc em C 4x4mm Step 1 Step 2 40834 37430 5x11mm Ball Bearing 40840 .....x2 40806 37430 38254 38254 12x15x0.25mm Shim .....x2 37430 3x10mm 40804 94003 3x10mm Hex Screw 94043 3x35mm Hex Screw .....x4 3x35mm 40840 38254 40815 .....x2 3x35mm 14 ASSEMBLY OF THE REAR SHOCK STAY Step 1 Step 2 40842 94003 3x10mm Hex Screw .....x3 3x10mm 40873 3x10mm 15 ASSEMBLY OF THE WING STAY 40842 94003 3x10mm Hex Screw 40842 .....
16 ASSEMBLY OF THE WING STAY Step 1 94004 3x12mm Hex Screw Step 2 .....x3 3x12mm 94005 3x15mm Hex Screw .....x1 40834 3x15mm 3x12mm 17 ASSEMBLY OF THE REAR LOWER ARMS 94035 3x8mm Set Screw .....x2 3x8mm 94004 3x12mm Hex Screw 40836 .....x2 40837 Ensure Free Movement 1:1 *A 3x8mm set screw is used to adjust ride-height. 40825 40837 3x8mm 40836 40816 Ensure Free Movement 1:1 3x12mm 18 ASSEMBLY OF THE REAR SUSPENSION ARMS 94001 3x4mm Hex Screw Assembly for both right and left side. .
19 ASSEMBLY OF THE REAR SUSPENSION ARMS Assembly for both right and left side. 3mm 37100 40828 30403 6mm Ball 30403 37100 .....x4 30403 94041 3mm Nylon Nut .....x2 94005 3x15mm Hex Screw .....x4 3x15mm 1:1 *Approx. 48mm 3x15mm 20 ASSEMBLY OF THE REAR STABILIZER 94035 3x8mm Set Screw Assembly for both right and left side. .....x2 30403 6mm Ball .....x2 94005 3x15mm Hex Screw Makes two rods for left and right hand-side. 40848 .....
222ASSEMBLY OF THE CENTER DIFF. MOUNT 3x10mm Step 2 Step 1 94033 3x3mm Set Screw Step 3 40844 40830 3x3mm 40844 .....x1 30171 94003 3x10mm Hex Screw 39243 39243 40830 .....x4 1:1 *Approx. 12mm 39243 5x8mm Flange Ball Bearing .....x2 40844 23 ASSEMBLY OF THE BRAKE DISK INTO CENTER DIFF. Step 2 Step 1 94033 3x3mm Set Screw 3x3mm .....x1 3x12mm * Remove the double-side tape before assembly. 40044 30171 38271 94004 3x12mm Hex Screw 40044 .....
25 ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS *Insert the drive shaft into the cap joint before assembly center diff. onto chassis. 94019 3x10mm Flat Head Hex Screw 40822 .....x4 3x10mm 3x10mm 26 ASSEMBLY OF THE REAR GEAR CASE ONTO CHASSIS *Insert the drive shaft into the cap joint before assembly rear gear box onto chassis. 40822 94019 3x10mm Flat Head Hex Screw .....x6 3x10mm 3x10mm 3x10mm 27 SUITABLE SERVO (CHECK YOUR SERVO BEFORE USE.
28 ASSEMBLY OF THE RADIO TRAY TYPE A 3x8mm 3x8mm Step 2 Step 1 40833 94018 3x5mm Flat Head Hex Screw.....x1 94002 3x8mm Hex Screw 40874 .....x10 3x8mm 3x8mm 3x5mm 40833 3x8mm 3x8mm TYPE B 3x8mm 3x8mm Step 2 Step 1 40833 94018 3x5mm Flat Head Hex Screw .....x3 94002 3x8mm Hex Screw .....x8 40833 3x8mm 94003 3x10mm Hex Screw 40833 .....
30 ASSEMBLY OF THE RADIO TRAY AND RECEIVER BOX 30560 40855 *Put the Servo and Switch wire into receiver box and connect to receiver . *Arrangement the servo wire as picture shown. 40833 37410 40861 *Use the AAA type bettery Receiver 31 ASSEMBLY OF THE RADIO TRAY ONTO CHASSIS 94019 3x10mm Flat Head Hex Screw .....x5 3x10mm 3x10mm 32 ASSEMBLY OF THE STEERING SERVO AND STEERING ROD 1:1 *Approx. 40mm *Ensure that servo gears are centered before attaching the servo horns.
33 ASSEMBLY OF THE FUEL TANK ONTO CHASSIS ²ÕX ¦ ªo½cÜ ¦ ©³½L TM-47 37070 37070 P3 O-Ring *Put the P3 O-Ring under the fuel tank before assembly. .....x2 94019 3x10mm Flat Head Hex Screw 37070 .....x2 Do Not Over Tighten 3x10mm 34 ASSEMBLY OF THE CLUTCH Step 1 Step 2 * Only use the #174D pilot shaft for threaded crank shaft engine. 10091 Pilot Shaft w nt e r (Not Included) S c me *Place the clutch shoes with the clutch springs over the 3 pins of the flywheel.
36 ASSEMBLY OF THE ENGINE ONTO CHASSIS Note book Paper. 94002 3x8mm Hex Screw *Use note book paper to set gear backlash between spur gear and clutch bell gear, applying pressure while retightening the engine. *If the space is not correct the spur gear will be damaged. .....x4 3x8mm 3x8mm 37 ASSEMBLY OF THE MANIFOLD AND MUFFLER 40879 Step 1 94034 4x4mm Set Screw Step 2 97501 .....x2 95700 94018 3x5mm Flat Head Hex Screw .....
39 ASSEMBLY OF THE THROTTLE LINKAGES INTO LEVER 3x3mm 10300 94033 3x3mm Set Screw 10300 .....x2 *Snap on. * Use the screw provided with your servo . Sanwa/Airtronics *Ensure that servo gears are centered before attaching the servo horns. The best way to accomplish this is by connecting the servos to the radio system and setting the trim to the center. S 10185 JR J Futaba F HiTech H * Choose the right servo horn adapter for your servo.
42 ASSEMBLY OF THE FRONT SHOCKS CORRECT SHOCK ASSEMBLY *Assemble 2 sets for front. Use 50wt oil for front. Step 1 USE THE LARGER 2 HOLE PISTON Step 2 2mm Fit the o-ring into groove before assembly. 37100 37967 C-Ring 2mm .....x2 37967 Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ball end and the shock body is 18mm for the front. 40863 37967 Washer (Black) 18mm N.B. Do not over tighten as the plastic will strip. 37966 40845 .....
44 ASSEMBLY OF THE FRONT SHOCK ABSORBER 3mm Nylon Nut 3x8mm 94041 3mm Nylon Nut .....x2 94040 3x8mm Washer .....x2 94005 3x15mm Hex Screw .....x2 3x15mm Assembly for both right and left side. 45 ASSEMBLY OF THE REAR SHOCK ABSORBER 94041 3mm Nylon Nut .....x2 94040 3x8mm Washer .....x2 3x8mm 94005 3x15mm Hex Screw 3mm Nylon Nut .....x2 3x15mm Assembly for both right and left side. 46 ASSEMBLY OF THE FRONT BUMPER Step 1 94003 3x10mm Hex Screw Step 3 40842 40842 .....
47 ASSEMBLY OF THE FUEL TUBE Connect to carbulater. 10177 Connect to fuel nipple. Connect to pressure nipple. Connect to fuel tank nipple. 10177 48 ASSEMBLY OF THE WING 3X10mm 40842 10803 40842 Body Reamer (Not included) 40852 Drill two 6mm holes for mounting. 94019 3x10mm Flat Head Hex Screw .....x2 49 ASSEMBLY OF THE TIRES AND WHEELS Step 1 Step 3 Step 2 Apply instant glue into the groove of the wheel.
50 ASSEMBLY OF THE TIRE ONTO FRONT KNUCKLE AND REAR HUB Assembly for both right and left side. 40865 40865 * For other wheels please assembly as picture shown. *Put the 5x8x0.8mm washer behind the 2mm pin. 40865 Tire and Wheel assembly. 5x8x0.8mm 40865 37390 40865 51 ASSEMBLY OF THE BODY AND PAINTING Cut out the body as shown. Use a neutral detergent to remove any dirt and oil.
52 MOUNTING BODY 37410 53 STARTING OF THE ENGINE How to start the engine: 12V Starter and Starter Ring ( Not Included) 1. 2. 3. 4. Turn on transmitter and then receiver. Fill fuel tank with fuel bottle. Connect 1.2V glow plug starter. Start engine with 12V starter. ( Note the direction of the starter.) 5. After the engine be started, remove the 1.2V glow plug starter. Starter rubber ring for car. ( Insert starter rubber ring on the 12V starter.) Glow Plug 1.
OPERATING YOUR MODEL SAFELY Before Running Your radio control model can move at high speed and therefore can cause injury to people or damage property. It is your responsibility to operate your model safely. Engine Start-Up While Running Cautions for Safety For engine use, refer to the manual included with the engine. Check that the model turns in proportion to the amount you move the steering control of the transmitter. Do not run your model through water. This may cause rust or electrical problems.
.12 ONLY
Jammin Mini CRT.5 Set-Up Sheet Date:________________ Driver:_________________ Track:_______________/_______ Air Temp:__________ Surface Dsc. ___________________________ Front Suspension Shock Spring: __________________ 5 4 3 Avg.
BLANK
Jammin Mini CRT.5 Set-Up Sheet Date:________________ Driver:_________________ Track:_______________/_______ Air Temp:__________ Surface Dsc. ___________________________ Front Suspension Shock Spring: __________________ 5 4 3 Avg.
BLANK
Jammin Mini CRT.5 Set-Up Sheet Date:________________ Driver:_________________ Track:_______________/_______ Air Temp:__________ Surface Dsc. ___________________________ Front Suspension Shock Spring: __________________ 5 4 3 Avg.
BLANK
MINI CRT.5 PRO PARTS LIST PART # DESCRIPTION RETAIL 10009 CLUTCH SHOES, RED, 3 SHOES 13.95 10098 CLUTCH NUT, SG SHAFT 4.95 10102 SPRINGS, CLUTCH, BLACK 3 PCS. 4.95 10120 SPRING, MANIFOLD, R.PORT .21 4.95 10177 FUEL LINE 3FT. GRAY/BLACK 1.95 10185 SILICONE JOINT TUBE BLACK 4.95 10270 CLIPS, FUEL LINE, BLK 3.95 10281 SW ITCH COVER, SILICONE RED 3.95 10300 ALUM. STOPPER KIT, 6 PCS. 4.95 10330 COLLET, FLYW HEEL INSERT .12/.21 2.95 10399 CLUTCH BELL W /BEARINGS, 13T 19.95 30171 LEVER, BRAKE 1.
BLANK
OPTION PARTS FOR CRT.5 30774 38457 40591 40872 40873 40874 40875 40876 40877 40878 40879 40880 40881 40882 40883 40884 40885 40886 40887 40888 40889 40890 40891 40892 40893 40894 40895 40896 40897 40898 40899 40900 40905 49009 ALU M . D IFF C R O SS PIN H C 6PC S. PAD , BR AKE, C AR BO N & ST EEL PAD BR AKE D ISK, FIBER X 1-C R /C R T C N C 7075 FR O N T SH O C K T O W ER C N C 7075 R EAR SH O C K T O W ER G R APH IT E R AD IO T R AY C R T .5 U N IVER SAL JO IN T F/R C R T .
BLANK
OWNER’S REGISTRATION CARD OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment. The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date.