Owner's manual

ManualsBrandsOFNA Racing ManualsCarsUltra GTP RTR

44

45

ASSEMBLY OF THE REAR SHOCKS

15

43

.....x2

.....x4

.....x2

.....x4

.....x2

.....x2

ADJUSTING THE ENGINE CONTROL LINKAGES

Approx. 1mm gap

(Neutral)

(Throttle High)

(Brake)

Idling adjusting

Screw

.

10300

0¬ù.5mm

Approx. 0.5mm

Carburetor is Opening fully

40090

2mm Washer

40090

1mm Washer

40090

2.6x6mm Washer

2.5mm Nylon Nut

40643

Shock Plastic

Ball End

(Short)

40090

40090

1mm

40090

2mm

40638

2.5mm

2.6x6mm

Washer

2.6x6mm

Washer

40054

1. Pull down piston and

pour oil into shock

cylinder.

2.To remove air bubbles

by slowly moving

piston up and down.

30403

6mm Ball End

*Fill the shocks

with oil approx 90%.

40090

3.5mm O-Ring

3. Pull down piston,

attach pressure top

and shock oil

overflow with tissue

paper.

40632

40637

40635

30403

Step 1

Step 2

40643

40633

40640

3

2mm

CORRECT SHOCK ASSEMBLY

Carefully screw the

shock shaft into the

bottom of the plastic

ball and until the

distance between the

ballend and the shock

body is 32mm for the

front.

N.B. Do not over tighten

as the plastic will strip.

10300

ASSEMBLY OF THE REAR SHOCKS

* Make 2 for Shocks for rear.

*Fit the o-ringinto groove before

assembly.

40090

40643

Shock Plastic

Ball End

(Short)

40090

40090

1mm

40090

2mm

40638

2.5mm

2.6x6mm

Washer

2.6x6mm

Washer

40736

1. Pull down piston and

pour oil into shock

cylinder.

2.To remove air bubbles

by slowly moving

piston up and down.

*Fill the shocks

with oil approx 90%.

3. Pull down piston,

attach pressure top

and shock oil

overflow with tissue

paper.

40737

40637

40635

30403

0 20

30

4010

Step 1

Step 2

40634

40636

40643

40633

40640

5

m

m

1

CORRECT SHOCK ASSEMBLY

Carefully screw the

shock shaft into the

bottom of the plastic

ball and until the

distance between the

ballend and the shock

body is 15mm for the

front.

N.B. Do not over tighten

as the plastic will strip.

.....x2

.....x4

.....x2

.....x4

.....x2

.....x2

40090

2mm Washer

40090

1mm Washer

2.6x6mm Washer

2.5mm Nylon Nut

30403

6mm Ball End

40090

3.5mm O-Ring

0 20

30

4010

* Make 2 for Shocks for front.

*Fit the o-ringinto groove before

assembly.

40634

40636

Turn on the Transmitter then Receiver and set the

Engine Control Servo Trim to the neutral position.

Adjust the idling adjusting screw on the Carburetor

to be open approx. 1mm gap.

Adjust both of the 10300 Engine Control and Brake

linkage accordingly.

Adjust the Engine while it is not running.

Adjust the Servo-Horn mounting position for the

Carburetor to be full open.

Change the pivot mounting position on the servo

horn in case the Carburetor is not opening fully or

if it is opening excessively. If available on the

Transmitter, adjust the Throttle high end point.

Adjust 10300 so the brakes work smoothly.

If the brakes apply too much or not enough,

adjust 30801 accordingly. Or if available on the

Transmitter, adjust the High-End Brake

adjustment.

Adjust 36140 to Change the front or Rear Brake.