www.kshbrands.com support@www.kshbrands.com OGAL-466A GREENHOUSE ASSEMBLY I NS TR U C T I O NS 1.888.965.
TO PREVENT INJURY, READ AND UNDERSTAND THE GREENHOUSE ASSEMBLY INSTRUCTIONS BEFORE USE. Notes: 1. It takes about 2-3 hours to assemble the greenhouse by 2-3 persons. 2.The UV-protected side of the sheet is covered with opal white film and must face towards the sun. 3.Remove approximately 2 inches of film from all sheet edges before installing.Removing all film immediately after the construction is completed 4.Make sure the greenhouse is located on a flat, level surface.
OGAL-466A 77 inches x 72 inches x 48 inches www.kshbrands.com support@kshbrands.com 1.888.965.
www.kshbrands.com support@kshbrands.com 1.888.965.
www.kshbrands.com support@kshbrands.com 1.888.965.
1 | OGAL-466A ASSEMBLY INSTRUCTIONS www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-466A ASSEMBLY INSTRUCTIONS | 2.1.1 Insert the bolts (F-B14) into the holes. 2.1.2 Insert F-05 into the bolts. Parts used in this section. Image Item# Quantity 2.1.3 & 2.1.4 Screw and tighten with nuts. www.kshbrands.com support@kshbrands.com 1.888.965.
Connec tF05,F19b,F18byt heupperbol t .Onc et henot c honF19bi s al i gnedwi t ht het opofF05,y ouc ans c r ewt henutt i ghtont hebol t .
OGAL-466A ASSEMBLY INSTRUCTIONS | 4.1 Connect F-41 & F-29 to F-05 with bolts and nuts. Maintain a 3/4 of an inch distance between the bolt and top of F-05. 3/4" 4.2 Connect F-29 to F-A02 with F-A14 bolt, do not tighten the nut yet. Image NOTICE: DON'T TIGHTEN NUTS. Item# Quantity Parts used in this section. www.kshbrands.com support@kshbrands.com 1.888.965.
| OGAL-466A ASSEMBLY INSTRUCTIONS 3/4" 5.1 Insert F-23 into the bolt to connect to F-04 and tighten the nuts. 5.2 Insert one bolt into F-23. Then perpendicularly attach F-41, and tighten the nut. Maintain a 3/4 of an inch from top of F-23 to bolt. NOTICE: Make sure 20mm from F-41 to the top of F-23. Parts used in this section. Image Item# Quantity www.kshbrands.com 3/4" 5 support@kshbrands.com 1.888.965.
OGAL-466A ASSEMBLY INSTRUCTIONS | 6.1 Connect F-30 and F-05 to the lowest notch of F-19b with bolts and nuts. 6.2 Connect F-30 and F-04 with bolts and nuts. NOTICE: DON'T TIGHTEN NUTS. NOTICE: The notch of F-19b MUST be aligned with the top of F-05. Parts used in this section. Image Item# 6.3 Place two bolts into F-05, connect F-30 and F-05 to the lowest notch of F-19b using the lowest bolt and nut. Insert the top bolt through the lower hole of F-19b. Quantity www.kshbrands.com support@kshbrands.
7 | OGAL-466A ASSEMBLY INSTRUCTIONS 7.1 Insert F-08/09/10/11 into the bolt and tighten the nuts. 7.2 Insert one bolt into F-08/09, connect F-18 and F-08/09 with the bolt & nut and tighten. Image Item# Quantity 7.3 Insert bolt into F-10/11, connect F-17 and F10/11 with bolt & nut, connect F-17 to F-05 by the hole of the bolt & nut in step 6.3. Parts used in this section. www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-466A ASSEMBLY INSTRUCTIONS | Insert the panels into each designated area. Parts used in this section. Image Item# Quantity www.kshbrands.com support@kshbrands.com 1.888.965.
9 | OGAL-466A ASSEMBLY INSTRUCTIONS 9.1 Insert the bolts and nuts into each hole of F-A06, but don't tighten the nuts yet. 9.2 Slide the bolts into the grooves of F-23. Slide the bolts into the grooves of F-05. Parts used in this section. Image Item# Quantity www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-466A ASSEMBLY INSTRUCTIONS | 10.1 Insert the bolts and nuts into each hole of F-A06, but don't tighten the nuts yet. 10.2 Insert two bolts into F-08/09/10/11. 10.3 Insert bolts and nuts into the hole of F-19b as shown. Parts used in this section. Image Item# Quantity www.kshbrands.com support@kshbrands.com 1.888.965.
11 | OGAL-466A ASSEMBLY INSTRUCTIONS 11.1 Insert F-06/07 through the bolts in F-19b and F-A06. Tighten the nuts. Parts used in this section. Image Item# Quantity 11.2+11.3 Insert two bolts into the grooves of F06 and F07. Then attach F-19 perpendicularly side which has three holes should face upward. www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-466A ASSEMBLY INSTRUCTIONS | 12.1 Secure one bolt into F-06 and F-07 through the hole in F-A7. Image Item# 12.2 Insert one bolt into F-06. Quantity Parts used in this section. www.kshbrands.com support@kshbrands.com 1.888.965.
13 | OGAL-466A ASSEMBLY INSTRUCTIONS 13.1 Insert F-40 into the top corner joining F-06 and F07. Connect F-12 and F-19 by bolt & nut. Image Item# Quantity Parts used in this section. www.kshbrands.com support@kshbrands.com 1.888.965.
Sl i det wobol t si nt oF24whi c hi si nt he r i ghts i deandonebol ti nt oF24i nt hel ef ts i de. 14. 3I ns er tt heupperbol ti nr i ghtF24andt he bol ti nl ef tF24t hr ought hehol esofFA07 andt i ght en.
15 | OGAL-466A ASSEMBLY INSTRUCTIONS Insert the panels into each designated area. Parts used in this section. Image Item# Quantity www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-466A ASSEMBLY INSTRUCTIONS | Slide F-A05 into F-A06 as shown. 16.1 Connect F-28 and F-24 with the bolts placed into F-24 and tighten the nuts. Parts used in this section. Image Item# Quantity www.kshbrands.com support@kshbrands.com 1.888.965.
17. 1. 1I ns er tt hr eebol t si nt ot hegr oov esofF13. 17. 1.
OGAL-466A ASSEMBLY INSTRUCTIONS | Parts used in this section. Image Item# Quantity 18.1 Slide two units F-26 over the sides of the F-37 window panel. 18.2 Slide F-27 over the bottom of the F-37 window panel. Slide F-25 over the top edge of the window panel. Secure with F-C14 nuts and bolts at all four corners. 18.3 Attach F-20 to F-27 using two F-C16 screws. www.kshbrands.com support@kshbrands.com 1.888.965.
19 | OGAL-466A ASSEMBLY INSTRUCTIONS 19.1 Slide the window into F-A07 according to the diagram. www.kshbrands.com support@kshbrands.com 1.888.965.
A panel panel s
21 | OGAL-466A ASSEMBLY INSTRUCTIONS 21.1 & 21.2 Slide the assembled door, ensuring the pulley wheels align to the middle notch of F-13 on top and F-03b on the bottom. 21.3 Secure door frame with nuts and bolts at bottom corners. Parts used in this section. Image Item# Quantity www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-466A ASSEMBLY INSTRUCTIONS | 22.1 & 22.2 Insert four G-P1 units into the corners of front and back walls of the greenhouse by sliding the rectangular section into each F-C05a panel. Parts used in this section. Image Item# Quantity www.kshbrands.com support@kshbrands.com 1.888.965.
23 | OGAL-466A ASSEMBLY INSTRUCTIONS 23.1 Slide the two G-P2 connectors into where F-A07 joins F-06 and F07. 23.2 & 23.3 Cap off F-13 with G-P3L at the left end and G-P3R at the right end. Secure with nuts and bolts. Parts used in this section. Image Item# Quantity www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-466A ASSEMBLY INSTRUCTIONS | When the window is closed, the handle of F-20 could be rotated to the right and fixed in place. I III www.kshbrands.com II IV support@kshbrands.com 1.888.965.
25 | OGAL-466A ASSEMBLY INSTRUCTIONS www.kshbrands.com support@kshbrands.com 1.888.965.