www.kshbrands.com support@www.kshbrands.com OGAL-666A GREENHOUSE ASSEMBLY I NS TR U C T I O NS 1.888.965.
TO PREVENT INJURY, PLEASE READ AND UNDERSTAND THE TO PREVENT INJURY, READ AND UNDERSTAND GREENHOUSE ASSEMBLY INSTRUCTIONS MANUALTHE BEFORE GREENHOUSE ASSEMBLY INSTRUCTIONS BEFORE USE. USE. Notes: Notes: 1. 2-3 hours is needed to assemble the greenhouse 2-3 1. Around It takes about 2-3 hours to assemble the greenhouse by 2-3by persons. individuals. 2.The UV-protected side of the sheet is covered with opal white film and 2. must The UV-protected sidesun.
6X6FT OGAL-666A 79 inches x 76 inches x 75 inches www.kshbrands.com support@kshbrands.com 1.888.965.
Rear Front Notes: 1. Remove approximately 2 inches of film from all the sheet edges prior to installation. Upon completion, immediately remove all the remaining film. 2. The UV-protected side of the sheet, which is covered with opal white film, must face the sun. www.kshbrands.com support@kshbrands.com 1.888.965.
www.kshbrands.com support@kshbrands.com 1.888.965.
1 | OGAL-666A ASSEMBLY INSTRUCTIONS 1.1 Create a right angle by positioning the parts of F-03b and F-04. However, make sure that the grooves of F-03b and F-04 are placed outside. 1.2 Form a right angle using two F-04 parts, but ensure that the edges of these pieces are located on the outside. These are the parts used in this section. Image Item No. Qty www.kshbrands.com support@kshbrands.com 1.888.965.
3
3. 1. 2ConnectF05,F19b,F18by t heupperbol t .Oncet henot chon F19bi sal i gnedwi t ht het opofF05, youcanscr ew t henutt i ghtont hebol t .
OGAL-666A ASSEMBLY INSTRUCTIONS | 4.1 Connect F-18 and F-29 to F-05 using bolts and nuts. When connecting these pieces, maintain a 3/4 of an inch distance from the bolts to the top of F-05. 4.2 Using bolts and nuts, connect F-29 to F-04. NOTE: Do not tighten the nuts yet. These are the parts used in this section. Image Item No. Qty www.kshbrands.com support@kshbrands.com 1.888.965.
5 | OGAL-666A ASSEMBLY INSTRUCTIONS 5.1 Connect F-30 and F-05 to the lowest notch of F-19b using bolts and nuts. NOTE: Align the top of F-05 with the notch of F-19b. These are the parts used in this section. Image Item No. Qty 5.2 Using bolts and nuts, connect F-30 to F-04. NOTE: Do not tighten the nuts yet. 5.3 Insert two bolts into F-05, then, connect F-30 and F-05 to the lowest notch of F-19b using the lower bolt and nut. next, insert the above bolt to the remaining lower hole of F-19b.
OGAL-666A ASSEMBLY INSTRUCTIONS | 6.2 Individually insert one bolt into F-08 and F-09. Then, connect F-18 to F-08 and F-09 and tighten using bolts and nuts. 6.1 Insert F-08, F-09, F-10 and F-11 into the bolt and secure it with nuts. These are the parts used in this section. Image Item No. Qty 6.3 Insert one bolt each i n t o F - 1 0 a n d F - 11 . Connect F-17 to F-10 and F-11 with bolts and nuts. Afterwards, connect F-17 to F-05 through the hole mentioned in step 5.3 using a bolt and nut. www.
7 | OGAL-666A ASSEMBLY INSTRUCTIONS 7.1 Connect F-23 to F-04 with a tightened nut and bolt. 7.2 Slide a bolt into the slit in F-23, and perpendicularly attach F-18 through the designated hole. Tighten the nut. These are the parts used in this section. Image Item No. Qty www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-666A ASSEMBLY INSTRUCTIONS | Slide the poly-carbonate panels into the designated area. These are the parts used in this section. Image Item No. Qty www.kshbrands.com support@kshbrands.com 1.888.965.
9 | OGAL-666A ASSEMBLY INSTRUCTIONS 9.1 Insert the bolts and nuts in each hole of F-B06, but do not tighten the nuts yet. Then, insert the bolts into the grooves of F-05. 9.2 Insert the bolts into the grooves of F-23. These are the parts used in this section. Image Item No. Qty www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-666A ASSEMBLY INSTRUCTIONS | 10.1 Place the bolt and nut into the hole of F-B06, but do not tighten the nut yet. 10.2 Insert two bolts each into F-08, F-09, F-10 and F-11. 10.3 Place the bolts and nuts in the hole of F-19b as shown in the picture, but do not tighten the nuts yet. This is the part used in this section. Image Item No. Qty www.kshbrands.com support@kshbrands.com 1.888.965.
11 | OGAL-666A ASSEMBLY INSTRUCTIONS 11.1 Insert F-06 and F-07 through the bolts inserted in F-19b and F-B06. then, tighten the nuts. 11.2 Slide the bolts which were inserted through F-08 and F-09 through the holes in F-19 as shown. These are the parts used in this section. Image Item No. Qty 11.3 Insert two bolts into the grooves of F-06 and F-07, then, cross the bolts into the hole of F-19 and tighten. NOTE: The side with 3 holes must be upward as correctly shown in 11.3 (left). www.kshbrands.
OGAL-666A ASSEMBLY INSTRUCTIONS | 12.1 Insert one bolt into F-06 and F-07, then insert into the hole of F-B07. These are the parts used in this section. Image Item No. Qty www.kshbrands.com support@kshbrands.com 1.888.965.
13 | OGAL-666A ASSEMBLY INSTRUCTIONS 13.1 Insert F-40 to F-06 and F-07. Afterwards, connect F-12 to F-19 using a bolt and nut. These are the parts used in this section. Image Item No. Qty www.kshbrands.com support@kshbrands.com 1.888.965.
14. 1Sl i deonebol ti nt ot hebot t om ofeach oft hef ourF24f r ames,andconnectt wo t oeachFB06f r amesatt het opoft hel ef t andr i ghtwal l s. 14. 2Sl i deonebol ti nt oeachF24i nt her i ght si deofr oof . 14. 3Sl i deonemor ebol ti nt ot het opsofeach oft hef ourF24f r amesandconnectt ot her i dge f r ameFB07.Ti ght enscr ews.
15 | OGAL-666A ASSEMBLY INSTRUCTIONS Place the poly-carbonate panels into each designated area. These are the parts used in this section. Image Item No. Qty www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-666A ASSEMBLY INSTRUCTIONS | 16.1 Connect F-28 to F-24 using the bolts left in F-24 and tighten with nuts. 16.2 Slide F-B05 into F-B06 as shown. These are the parts used in this section. Image Item No. Qty www.kshbrands.com support@kshbrands.com 1.888.965.
t hr ee
OGAL-666A ASSEMBLY INSTRUCTIONS | 18.1 Slide two units of F-26 over the sides of the F-37 window panel. 18.2 Slide F-27 over the bottom of the F-37 window panel. j 18.3 Slide F-25 over the top edge of the window panel. 18.4 Secure with F-B14 nuts and bolts at all four corners. These are the parts used in this section. Image Item No. Qty 18.5 Attach F-20 to F-27 using two F-B16 screws. 18.5 www.kshbrands.com support@kshbrands.com 1.888.965.
19 | OGAL-666A ASSEMBLY INSTRUCTIONS 19.1 Slide the window into F-B07. You should be able to pivot it up and down. www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-666A ASSEMBLY INSTRUCTIONS | Connect each part as shown in the pictures. These are the parts used in this section. Image Item No. Qty 20.2 Secure F-15 and F-16b with screws. 20.1 and 20.3 Insert F-22b into F-16b and secure it with screws. NOTE: The Þrst screw is F-B16, and the second screw is F-B15a. www.kshbrands.com support@kshbrands.com 1.888.965.
21 | OGAL-666A ASSEMBLY INSTRUCTIONS 21.1 and 21.2 Slide the door into the structure. Use the diagrams below as references. d in thi s se cti on . These are the parts used in This is the part used in this section. Image Item No. Qty www.kshbrands.com 21.3 Screw the bolts and nuts into holes of F-03b. support@kshbrands.com 1.888.965.
OGAL-666A ASSEMBLY INSTRUCTIONS | 22.1 and 22.2 Insert G-P1 to each corner. 22.3 and 22.4 Fix G-P3L and G-P3R in F-13 using bolts and nuts. These are the parts used in this section. Image Item No. Qty 22.5 Insert G-P2 to F-B07. www.kshbrands.com support@kshbrands.com 1.888.965.
23 | OGAL-666A ASSEMBLY INSTRUCTIONS When the window is closed, the handle of F-20 could be rotated to the right and fixed in place. I II III www.kshbrands.com IV support@kshbrands.com 1.888.965.
OGAL-666A ASSEMBLY INSTRUCTIONS | RECOMMENDATION It is recommended to place glue or tape between the poly-carbonate panel and the aluminum frame to provide better stability. NOTE: 뺭 1. The silicone sealant and glue gun are not included in the tool kit. You may purchase these items locally. 2. Only silicone sealant is suitable for aluminum. www.kshbrands.com support@kshbrands.com 1.888.965.