OKIJET ® 2500 User’s Guide
Every effort has been made to ensure that the information in this document is complete, accurate and up-to-date. Okidata assumes no responsibility for the results of errors beyond its control Okidata also cannot guarantee that changes in software and equipment made by other manufacturers, and referred to in this handbook, will not affect the applicability of the information in this manual. Mention of software products manufactured by other companies does not necessarily constitute endoresment by Okidata.
Contents Printing from Windows 95 Applications ....................... 15 Checking Printer Settings .............................................. 16 To Open the OKIJET 2500 Printer Setup Dialog Box From Windows 3.1x Control Panel ...................... 16 In Windows 95 ...................................................... 16 Canceling or Pausing a Print Job ................................... 17 Windows 3.1x............................................................ 17 Windows 95 ........................
Contents Transporting the Printer ................................................... 27 Cleaning the Printer ......................................................... 29 Section 4: Control Panel................................................ 31 Control Panel ................................................................... 31 Control Panel Buttons ................................................... 31 Power/Reset Button................................................... 31 Resume/FF Button .............
Important Safety Instructions • Be certain that your power source matches the rating listed on the back of the printer. If you are not sure, check with your dealer or with your local power company. • Your printer has a grounded, 3-prong plug as a safety feature, and it will only fit into a grounded outlet. If you can not plug it in, chances are you have a non-grounded outlet; contact an electrician to have it replaced with a grounded outlet. Do not use an adapter to defeat the grounding.
Important Safety Information total ratings of all equipment plugged into any one power line should not exceed 15 amperes. Do not exceed this unless you know that the power line your equipment is plugged into has a rating above 15 amperes. • Aside from the routine maintenance described in this handbook, do not try to service the printer yourself; opening the cover may expose you to shocks or other hazards.
1 Setup Smarter Color System • Individually replaceable ink cartridges • True sensing of ink levels with both “Low Ink” and “Cartridge Empty” indicators for each color OKIJET 2500 Features Easy to Use • Compatible with Windows® 95, Windows 3.
1 Setup Select a Location Make sure you have: ➊ Printer ➋ Output Shelf ➌ Power Cord ➍ Color Printhead ➎ 4 Ink Cartridges (1 black, 1 cyan, 1 magenta, 1 yellow) ➏ Printhead Storage Box ➐ Diskette(s) Select a flat, stable surface with space above and in front of the printer to provide adequate ventilation. • Avoid direct sunlight • Avoid air conditioners and heat sources • Avoid areas with high vibration • Avoid dusty/dirty environments Unpack the Printer Anything missing or damaged? Contact your dealer.
Setup Paper Guide Lever Getting to Know Your Printer 1 Output Shelf Top Cover Paper Support Output Shelf Envelope Feed Guide (behind output shelf, in paper tray) Power Cord Socket Paper Guide Lever (behind output shelf, on paper tray) Paper Tray Top Cover Parallel Cable Connector Printhead Storage Box Printhead Storage Box Back View Resume/FF Button Power/Reset Button Cartridge Change/Clean Button On/off Switch Power LED Front View Low Ink Indicators Error LED Control Panel 3
1 Setup Connect to the Computer Connect to Power You’ll need an IEEE-1284-compliant, parallel, bi-directional interface cable. 1. Insert power cord. 1. Turn off the computer. 2. Turn off the printer (press and hold the Power/Reset button for approximately 2 to 5 seconds). 2. Connect to a grounded power outlet. 3. Plug the parallel interface cable into the printer and secure it with the wire clips.
Setup ! To protect against damage to the printhead, ensure that the printer has stopped its operation completely (carriage at its left most “home” position) before detaching the power cord. ! Do not unplug the printer for long periods of time: the printhead nozzles can dry out. ! Do not use a power strip to control the power to the printer. The printer requires a small amount of power, even when off, in order to maintain the printhead.
1 Setup 2. Open the top cover. 4. Unpack the printhead. Be careful not to touch the printhead nozzles when removing the printhead from the plastic bag. Ink will get on your hands and the printhead can become contaminated. ! 3. Make sure the green cartridge lock lever is forward. 1 5. Holding the bag upside down as illustrated, remove the black ink cartridge from its plastic bag.
Setup 6. Carefully peel the plastic foil seal off the ink cartridge in the direction of the arrows printed on the seal. ! 1 8. Repeat steps 5 to 7 for each color cartridge, matching the color/number on the ink cartridges with the corresponding color/number on the printhead. Do not force the ink cartridges into the printhead! 9. Align the rectangular hole in the printhead (➊) with the green post (➋) on the printer carriage, then gently lower the printhead into position. 7.
1 Setup 10. Push the green cartridge lock lever back to secure the printhead and close the cover. Install the Printhead Storage Box For those who have both the optional high-capacity black printhead and the standard color printhead, the printhead storage box is designed to protect one while the other is in use. It is also used to store the printhead when the printer is being transported. Attach the box (➊) included with your printer to the back of the housing: 11.
Setup Usable Print Media 1 Be sure to select the proper media in the Main tab and media size in the Page tab of the OKI OKIJET 2500 printer setup dialog box (see page 15). Media Use Media Setting(s) Media Size Setting(s) Cards Cards designated for inkjet printers. Plain Paper • US 4x6 OR US 5x8 • A6 (105 x 148 mm) • Hagaki (100 x 148 mm) Envelopes Only short-flap, side-seam type, designated for inkjet printers. Plain Paper • #10 (4.125 x 9.
1 Setup Recommended Print Media Load Paper Note: To change the print quality settting, open the OKI OKIJET 2500 printer setup dialog box and select the desired print quality in the Main tab.
Setup 1 4. Slide the paper guide lever to touch the right edge of the paper stack. 3.Fan a stack of paper and load it into the paper tray (max. 125 sheets 20-lb paper), with the side to be printed facing the back. 5. Install the output shelf behind the green tabs(➊), with the ribs facing forward. Make sure you insert the tabs on the shelf into the cutouts in the feed area. ➊ ➊ To load envelopes, banners and other print media, see page 18, ff.
1 Setup If the demo page shows streaks or missing colors, press and hold the Cartridge Clean button to start the cartridge cleaning process. Print the Demo Page We recommend that you run a demo print whenever the printer is moved or the ink cartridge is replaced. The printer does not need to be attached to a host computer to perform this demo. 1. Make sure that at least 4 sheets of paper are loaded and that the printer is turned on (Power LED lit: if not, press Power/Reset button). 2.
2 Printing Installation on Windows 3.1x Install the Printer Driver/Electronic Registration Utility For Windows 3.1 or Windows for Workgroups 3.11: 1. Start Windows on your computer (make sure all other programs are closed before proceeding). 2. Insert the OKI OKIJET 2500 CD in your CD ROM drive. 3. From the Program Manager, choose File, then select Run. 4. Type d:\setup, then click OK. The Welcome dialog box appears. 5. Click Next. The Software License Agreement appears. 6. Click Yes.
2 Printing 7. Clear any components you do not wish to install (see note below regarding the various registration options available to you), then click Next. The Printer Port Selection dialog box appears. 8. Select the port you wish to use (normally LPT1:), then click Next. The Select Program Folder dialog box appears. 9. Click Next. 10. Click Next to start copying the files, then follow the remaining steps of the installation program. Installation on Windows™ 95: 1.
Printing To run the Win 95 Electronic Registration utility: On-Line Help The printer control software has extensive on-line Help, accessible from any dialog box. Click the Help button or press the F1 function key. You must have a modem installed in your PC in order to use Electronic Registration. If you do not have a modem, you can still use the Electronic Registration utility to fill out the registration form, then print out a copy and fax it or mail it in.
2 Printing To Open the OKI OKIJET 2500 Printer Setup Dialog Box From Windows 3.1x Control Panel Checking Printer Settings You can check the printer settings by opening the OKI OKIJET 2500 printer setup dialog box: 1. Double click the Printers icon. 2. Set OKIJET 2500 as the default printer. 3. Click Setup. The settings you make will apply to all print jobs and all Windows 3.1x-based applications. In Windows 95 1. Click Start, Settings, Printers. 2.
Printing 2 Canceling or Pausing a Print Job Printing from DOS Applications Windows 3.1x To print from DOS applications which have the capability of selecting a printer driver: 1. Click the Print Manager icon from the Main group. 2. Click the document name. • To cancel the print job, click Delete. • To pause the print job, click Pause. When you are ready to resume printing, click Resume. 3. Close the Print Manager window. 1.
2 Printing If an ERROR message appears, check the install directory specified to be sure that it is a valid path, then try again. The OKIJET 2500 DOS Control Panel Installing the DOS Control Panel To install the DOS Control Panel on your computer: Loading the DOS Control Panel for Use 1. Insert the DOS Control Panel diskette supplied with the printer in your 3-1/2" floppy disk drive. 2. At the MS-DOS prompt, type a:install (or b:\install, if b is your 3-1/2" drive) and press Enter.
Printing To load envelopes: 2 3. Place the envelopes against the feed guide, address side against the paper tray—flap to the left, then move the paper guide lever over to touch the right edge of the envelopes and replace the output shelf. 1. Remove any print media from the paper tray. 2. Remove the output shelf and flip up the envelope feed guide (➊). 5.
2 Printing 3. Adjust the paper guides for the width of the banner paper, then carefully insert the leading edge of the banner into the paper tray. Banners Printing on fan-fold banner paper can only be done using a software package which fully supports this feature, such as Corel Draw®. Some software packages may allow you to select “banner” printing, but only work if you feed in single sheets of paper then tape them together to form the banner.
3 Maintenance 3. Open the top cover. Replacing/Swapping the Printhead Keep the printhead and ink cartridges out of the reach of children. Do not get the ink near your eyes or mouth. ! Do not touch the ink nozzles when removing the printhead! The printhead can become contaminated, and ink, which is not easily removed, will get on your hands and/or clothing. 4. Once the carriage moves to the center and stops, pull the green cartridge lock lever to the forward position and remove the printhead.
3 Maintenance 5. Install the new/swapped printhead: align the rectangular hole in the printhead with the green post (➊) on the printer carriage, then gently lower the printhead into position. 7. Close the top cover. When installing a new color cartridge, insert the four color ink cartridges into the printhead before installing the printhead in the printer. ➊ ! To avoid premature failure of the printhead, the printhead must be stored in the storage box when not installed in the printer. 8.
Maintenance 9. Press and release the Cartridge Change/Clean button. 3 Replacing the Ink Cartridges Keep the ink cartridges out of the reach of children. Do not get the ink near your eyes or mouth. ! The printer will prepare the cartridge for printing. Be careful not to touch the ink nozzles when handling the printhead. Ink will get on your hands and the printhead can become contaminated. 1. Press and release the Cartridge Change/Clean button.
3 Maintenance 2. Open the top cover. ! Do not remove the ink cartridge until you have a replacement cartridge to install! 4. Remove the empty ink cartridge from the printhead. 3. Pull the green lock lever forward and remove the printhead. The Low Ink lights will all flash, indicating that the printhead is removed. 5. Holding the bag upside down as illustrated, remove the ink cartridge from its plastic bag.
Maintenance 6. Carefully peel the plastic foil seal off the cartridge in the direction of the arrows printed on the seal. ! 3 8. Reinstall the printhead and push the green lock lever back. Do not force the ink cartridge into the printhead! 9. Close the top cover. 7. Insert the ink cartridge into the printhead and snap it firmly down into position.
3 Maintenance 10. Press and release the Cartridge Change/Clean button. The printer prepares the printhead for printing. 2. Press and hold the Cartridge Change/Clean button two seconds. for 3. Print the Test page (turn the printer off, then press the while turning it back on). If the Test Resume/FF button page shows nozzles not firing, repeat steps 1 and 2. Aligning the Printhead In Windows 3.1 or Windows for Workgroups 3.11: 1. 2. 3. 4. Cleaning the Printhead Nozzles To clean the printhead nozzles 1.
Maintenance In Windows 95: 1. 2. 3. 4. 5. 6. 7. 8. 3 Transporting the Printer Click Start, Settings, Printers. Click the OKIJET 2500 icon with the right mouse button. Click the Printer tab. Click Align, then Yes. The test page prints. Click the number which corresponds to the straightest set of vertical lines on the test page. Click Align. The test page prints. Repeat steps 5 and 6 until the straightest set of lines corresponds to 0. Click Done and exit back out.
3 Maintenance 2. Place the color printhead in the printhead storage box. If you swapped the color and black printheads, you will need to remove the black printhead from the printer before reinstalling the color printhead. 2. Make sure paper is loaded, then press the Power/Reset button to power up.
Maintenance 3. Slightly dampen a soft, clean cloth with water and wipe the printer cover. Cleaning the Printer ! 3 To avoid damage to the printer: • Do not pour or spray any liquid directly on the printer. • Use only water to moisten the cleaning cloth: do not use detergent, alcohol, etc. 4. Dry the printer cover with a clean cloth. 5. Plug the power cord back into the outlet. 1. Press and hold the Power/Reset button for 2 to 5 seconds to stop the printer’s operation. 6.
3 Maintenance 30
4 Control Panel Control Panel Control Panel Buttons Each button and LED on the control panel has multiple functions. Power/Reset Button Resume/FF Button Power/Reset Button Cartridge Change/Clean Button Low Ink Indicators Power LED Error LED Function Action Turn the printer on. Press and release. Turn the printer off. Press and hold for 2 to 5 seconds. Reset the printer. With the printer on, press and release. The data remaining in the buffer is cleared.
4 Control panel Resume/FF Button Cartridge Change/Clean Button Function Action Function Resume printing. If the printing has paused, press and release. Change ink cartridge(s). Form Feed. Press and release. Eject paper. Press and hold for 2 to 5 seconds. Clear error (Error LED lit). Press and release. Print Demo page. Make sure: 1. Paper is loaded. 2. There are no print jobs in progress. 3. There is no paper in the print path. Then press and hold the Resume/FF button for 2 to 5 seconds.
Control Panel 4 Low Ink Indicators Control Panel Indicator Lights Power LED Condition Meaning On Printer is on-line and ready to print. Blinking Printer is processing data. Condition Meaning Off Ink cartridge contains sufficient ink. On Cartridge is getting low on ink (about 10 to 15% left): make sure you have a replacement cartridge on hand. Blinking Ink cartridge is empty and must be replaced. Ink cartridge is installed incorrectly Wrong brand of ink cartridge is installed.
4 Control panel 34
5 Troubleshooting 2. Fan the paper and reinstall it in the paper tray. Clearing Paper Misfeeds The Error LED will be lit to indicate a misfeed. To clear a paper misfeed: 1. Remove all paper from the paper tray. 3. Press and release the Resume/FF button to continue the print job. If the misfeeds continue, flip the paper stack over (keeping the print side facing the paper support) and press and release the Resume/FF button to continue the print job.
5 Troubleshooting If the Trailing Edge is Not Accessible Clearing Paper Jams 1. If you cannot get to the trailing edge of the paper in the paper tray, remove the unused paper from the tray. If the Trailing Edge is Accessible If the trailing edge of the paper is accessible in the paper tray, grasp it, then press the Resume/FF button for 2 to 5 seconds. This frees up the paper so that you can pull it out. 2. Remove the output shelf. To continue the print job, press the Resume/FF button.
Troubleshooting 3. Press back firmly on the green plastic tabs at either side of the paper tray until they unsnap, then remove the paper tray, observing carefully how the tray is installed. 7. Reinstall the output shelf. 4. Remove the jammed sheet of paper from the printer. 5. Press in on the feed plate (➊) and insert the tray into the back of the printer at the bottom of the tray opening, then pivot the tray toward you and release the feed plate. 8. Fan the paper and reinstall it in the paper tray.
5 Troubleshooting 4. Remove the Star Wheel bar: a. Press in firmly at either end to disengage the latch tabs. Clearing Multi-Page Paper Jams If a clump of 10 or more pages has jammed in the printer, removing the paper tray will not allow sufficient clearance to extract it. To correct such a paper jam: 1. Follow steps 1 through 4 under “If the Trailing Edge is Not Accessible” (see pages 36-37). 2. Remove the top cover: a.
Troubleshooting 5. While pressing down on the green dot inside the printer, remove the jammed paper. 6. Reinstall the Star Wheel bar: a. Insert the pins (➊) in the cradles (➋) at either end and push the bar firmly down into place. 5 7. Reinstall the top cover (insert pin in the hole on one side, then press against the opposite side to slip its pin into the corresponding hole). ➊ ➋ 8. Follow steps 5 through 8 under “If the Trailing Edge is Not Accessible” (see page 37). b.
5 Troubleshooting Problem Solving Problem Possible Meaning(s) Solution(s) Printer Power LED does not turn on. No power from outlet Connect the power cord to a different power outlet. Power cord is not securely inserted into the power outlet and/or the printer. Remove the power cord from the wall outlet, then remove it from the printer and reinsert it. Plug the power cord back into the wall outlet. Power cord is damaged. Check the power cord and replace if damaged.
Troubleshooting 5 Problem Possible Meaning(s) Solution(s) Data is sent, but not printed. Printer is not set for local port. Check the port setting (usually lpt1) for your printer to be sure that it is not being directed either to a remote printer or to print to file. (See the Details tab of the OKI OKIJET 2500 printer setup dialog box.) Interface cable is not connected properly. Press and release the Power on/Reset button to make the printer stop its operation.
5 Troubleshooting Problem Possible Meaning(s) Solution(s) Error LED is on. Printer is out of paper. Add paper to the paper tray and press the Resume /FF button. Printhead has not been correctly installed. Remove and reinstall the printhead. Carriage position error has occurred. 1. Press the Resume /FF button to clear the error and eject the paper. 2. Ensure that all packing material is removed. Paper feed error has occurred. If paper has misfed, remove the jammed paper.
Troubleshooting 5 Problem Possible Meaning(s) Solution(s) White horizontal lines and streaks appear in the printing. The printhead nozzles are blocked. 1. Press the Cartridge Change/Clean button for 2 to 5 seconds to clean and restore the printhead. 2. Print the Test page (hold Resume/FF button while turning printer on). If the Test page shows nozzles not firing, repeat the above process up to 5 times. If the problem continues, replace the printhead. The ink cartridge is empty.
5 Troubleshooting Problem Possible Meaning(s) Print is faint or missing (continued). The printhead nozzles are blocked. 1. Press the Cartridge Change/Clean button for 2 to 5 seconds to clean and restore the printhead. 2. Print the Test page (hold Resume/FF button while turning printer on). If the Test page still shows nozzles not firing, repeat step 1 two more times. If the problem is still not corrected, replace the printhead. The ink cartridge is clogged, defective, or empty.
Troubleshooting 5 Problem Possible Meaning(s) Solution(s) Print image is clipped or off the edge of the print media. The selected document margins exceed the printer margins. Adjust the margins in the application as necessary. Incorrect settings for media size and/or type in the printer driver setup. Ensure correct selection of media size and type in the printer driver setup. Printing on one page of the document suddenly gets much larger and that page flows onto several pages.
5 Troubleshooting Problem Possible Meaning(s) Solution(s) Paper does not stack neatly in the output tray. The Star Wheel bar is not properly engaged. Remove the top cover (see page 38, ff.) and make sure that the Star Wheel bar is firmly engaged, then replace the top cover. The star wheels in the Star Wheel bar are jammed or askew. Remove the Star Wheel bar (see page 38) and make sure all the star wheels can rotate freely, then reinstall the Star Wheel bar. Low Ink Indicator on.
6 Specifications Printer Specifications Print Method: Four-color thermal, drop-on-demand ink jet Print Speed: Color Printhead (standard): Black printing: up to 5 ppm Color printing: up to 2.5 ppm Print resolution: 1200 x 600 dpi on glossy paper; 600 x 600 dpi on plain paper (addressable dots per inch) High-Capacity Black Printhead (option): up to 7 ppm Printhead Nozzles: Color Printhead (standard): 120 nozzles—24 cyan, 24 magenta, 24 yellow, 48 black Compatibility: Microsoft Windows 3.
6 Specifications Resident: typefaces Output Tray: Courier, CG Times, Univers 50 sheets 20 lb.
Specifications 6 Paper Specifications Envelope Specifications Most types of paper will work well in your printer, although some variables in paper composition may affect print quality. Most high-grade photocopying papers produce good results. The majority of cotton bond papers also yield excellent results. Paper should be tested fully before large quantities are purchased. Most types of envelopes will work well in your printer. Some variables in paper composition may affect the quality of the printing.
6 Specifications Label Specifications ! Card Specifications Always use labels designed specifically for ink jet printers. Use only paper face label stock. Ink will not dry on vinyl, plastic, or clear label stock. Use only full sheets of labels: partial sheets can jam the printer! Do not use any label material which is partially used, folded, curled, or wrinkled. Sheet Feeder Capacity Up to 10 cards Weight 90 lb. (163 g/m2) max. Minimum Size 3.9" x 3.
Customer Support & Service 7 Okidata Information System Automated Attendant Getting Support and Service For automated customer support information, call 1-800-OKIDATA (1-800-654-3282): available 24 hours a day, 7 days a week, providing immediate assistance with: This information is valid for the United States and Canada only.
7 Customer Support & Service Okidata Customer Support Professionals Okidata Faxable Facts Agents are available 24 hours a day, seven days a week. Call 1-800-OKIDATA (1-800-654-3282). Please call from a telephone close to your printer, so you can refer to it directly as needed during the conversation.
Customer Support & Service Okidata Service Locations For the latest list of Okidata Service Centers, see the Okidata Web site at http://www.okidata.com. • Allow 3½ business days for repair. • Carry-in repairs must be called in first to schedule service. • Before shipping your printer, you must call and obtain a return authorization number. USA USA Okidata 57 Carnegie Plaza Cherry Hill, NJ 08003 Attn.: Field Service Dept. Phone: 1-800-654-3282 Fax: 1-609-222-5247 Okidata 851 Feehanville Drive Mt.
7 Customer Support & Service Purchasing Replacement Parts & Accessories Accessories & Service Manual Before you order, know your printer model number (see the front of the printer) and have the correct part number and description of the item. Item Order No. Black Printhead (➊) .............. 52110101 Service Manual ..................... 59272601 ➊ Ways to Purchase Replacement Parts • Consult the dealer where your purchased your printer. • Consult an Okidata Authorized Sales or Service Dealer.
Transporting the Printer Transporting the Printer under Special Conditions A 1. Open the cover, pull the lock lever forward and lift out the color printhead. If you will be transporting the printer under either or both of the following conditions: • Elevation Changes greater than 1,000 feet • Temperature Changes greater than 20ºF (10ºC) you will need to remove the color printhead and the individual ink cartridges before transport.
A Transporting the Printer 2. One at a time: a. Remove each ink cartridge, and wipe the area around the ink port dry with a tissue. As soon as possible after the move: 1. Remove the color printhead from the storage box. 2. Unpack and wipe off the ink cartridges, then snap each ink cartridge into the corresponding color/number slot in the printhead. b. Wrap the cartridge in plastic wrap (keep ink port up to minimize ink spillage), and tape the wrap securely. 3.
Transporting the Printer 2. Make sure paper is loaded, then press the Power/Reset button to power up. 4. Press and hold the Resume/FF button for 2 to 5 seconds to run a demo print.
FCC, IC, CE Statements Federal Communications Commission Radio Frequency Interference Statement It is the responsibility of the user to obtain the required shielded cable in order to ensure compliance of this equipment with FCC regulations. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Limited Warranty Okidata, division of Oki America, Inc. (Okidata) warrants this printer to be free from defects in material and workmanship and will remedy any such defect according to the terms of this Limited Warranty. This Limited Warranty does not extend to consumable items, including but not limited to print cartridges, etc. Okidata warrants that this machine is manufactured from new parts, or new and serviceable used parts which perform like new parts, and that it is in good working order.
Limited Warranty Additional information on obtaining service under this Limited Warranty is available by contacting the Okidata dealer from whom the product was purchased, by contacting Okidata directly at 1-800-OKIDATA (1-800-654-3282), or by contacting one of the service depots listed under “Okidata Service Locations” on pages 52 and 53. This Limited Warranty applies to all OKIJET 2500 printers. The procedure for obtaining service may vary outside the continental United States and Canada.
Overnight Exchange Overnight Exchange is not available for machines that have been defaced, altered, or damaged beyond repair. When Overnight Exchange is used, the returned machine becomes the property of Okidata. Available in the United States and Canada only. If you choose to use our Overnight Exchange service, call 1-800-OKIDATA (1-800-654-3282): our trained personnel will try to solve your problem over the phone.
Glossary Acronyms Ink Jet. One nozzle of an ink jet printer head. CMYK. Cyan/Magenta/Yellow/Black: K is used for black because B is used to represent blue in RGB. Ink Jet Printer. A type printer that heats the ink to a boiling point in a nozzle to form a bubble. When the ink expands, the ink is projected onto the paper. cpi. Characters per inch. Internal Fonts. Fonts which are resident in the printer. cpl. Characters per line. Parallel Interface.
Material Safety Data Sheet (MSDS) Ingredients MSDS No. 58321301 for OKIJET 2500 Black Ink Cartridge (P/N 52110001) For more information, contact OKIDATA 532 Fellowship Road, Mt. Laurel, NJ 08054-3405. For emergency information, contact Okidata’s agent, the Xerox Customer Safety hotline, 24 hours a day, at 1-800-828-6571.
MSDS: Black Ink Fire and Explosion Hazard Data Spill Cleanup and Disposal Flash Point: Non-flammable Autoignition Point: N/A* Flammability Limits, LEL, UEL: N/A* Extinguishing Media: N/A* Special Fire and Explosion Procedures: None Unusual Fire and Explosion Hazards: None. Spill Cleanup: Use absorbent towel to wipe up the ink. Rinse area with water. Waste Disposal: Not a hazardous waste according to Federal Regulation 40 CFR 261.
Material Safety Data Sheet (MSDS) Ingredients MSDS No. 58321401 for OKIJET 2500 Cyan Ink Cartridge (P/N 52110002) For more information, contact OKIDATA 532 Fellowship Road, Mt. Laurel, NJ 08054-3405. For emergency information, contact Okidata’s agent, the Xerox Customer Safety hotline, 24 hours a day, at 1-800-828-6571. Procedure Contact occurs with skin. Wash affected area with soap and water. Contact occurs with eyes.
MSDS: Cyan Ink Fire and Explosion Hazard Data Spill Cleanup and Disposal Flash Point: Non-flammable Autoignition Point: N/D* Flammability Limits, LEL, UEL: N/A* Extinguishing Media: N/A* Special Fire and Explosion Procedures: None Unusual Fire and Explosion Hazards: None. Spill Cleanup: Use absorbent towel to wipe up the ink. Rinse area with water. Waste Disposal: Not a hazardous waste according to Federal Regulation 40 CFR 261. Dispose of in accordance with all applicable Federal, State and Local laws.
Material Safety Data Sheet (MSDS) Ingredients MSDS No. 58321501 Water: 40-45% CAS # 7732-18-5 OSHA PEL N/E* ACGIH TLV N/E* Trade Secret Ingredient: 20-30% New Jersey Trade Secret Registra’n # 1664900-5015P/5742P/5695P for OKIJET 2500 Magenta Ink Cartridge (P/N 52110004) For more information, contact OKIDATA 532 Fellowship Road, Mt. Laurel, NJ 08054-3405.
MSDS: Magenta Ink Fire and Explosion Hazard Data Spill Cleanup and Disposal Flash Point: Non-flammable Autoignition Point: N/D* Flammability Limits, LEL, UEL: N/A* Extinguishing Media: N/A* Special Fire and Explosion Procedures: None Unusual Fire and Explosion Hazards: None. Spill Cleanup: Use absorbent towel to wipe up the ink. Rinse area with water. Waste Disposal: Not a hazardous waste according to Federal Regulation 40 CFR 261.
Material Safety Data Sheet (MSDS) Ingredients MSDS No. 58321601 for OKIJET 2500 Yellow Ink Cartridge (P/N 52110003) For more information, contact OKIDATA 532 Fellowship Road, Mt. Laurel, NJ 08054-3405. For emergency information, contact Okidata’s agent, the Xerox Customer Safety hotline, 24 hours a day, at 1-800-828-6571. Procedure Contact occurs with skin. Wash affected area with soap and water. Contact occurs with eyes.
MSDS: Yellow Ink Fire and Explosion Hazard Data Spill Cleanup and Disposal Flash Point: Non-flammable Autoignition Point: N/D* Flammability Limits, LEL, UEL: N/A* Extinguishing Media: N/A* Special Fire and Explosion Procedures: None Unusual Fire and Explosion Hazards: None. Spill Cleanup: Use absorbent towel to wipe up the ink. Rinse area with water. Waste Disposal: Not a hazardous waste according to Federal Regulation 40 CFR 261.
Index A C D G A4 label sheets ........................ 50 paper ................................. 48 transfer media ................... 50 transparencies ................... 49 Accessories ............................ 54 Acronyms .............................. 62 Add printer wizard................. 14 Alignment, printhead ....... 26-27 Cable, interface .................. 2, 11 Canceling a print job ............. 17 Card specifications ................ 50 Cartridge change/clean button ..........
Index J Jams, paper ...................... 36-39 L Label specifications ............... 50 LEDs error ............................ 33, 42 low ink ........................ 33, 46 power ................................ 33 Legal paper ............................ 48 Lights, indicator ..................... 33 Loading envelopes ........... 18-19 Loading paper .................... 8–10 Location ................................... 1 Lock lever, cartridge .................. 5, 7, 21, 22 Low ink indicators ........
Index Resident typefaces ................. 47 Resolution .............................. 47 Resume/FF button.................. 32 S Service information ......... 51-54 Service locations .............. 52-53 Service manual ...................... 54 Specifications................... 47–50 cards .................................. 50 envelope ............................ 49 label................................... 50 paper ................................. 48 transfer media ................... 50 transparency .
Index 74
