Product Manual
6
2 4
PAIRING LED LIGHT WITH "SMART LIFE" APP
Step 4:How to pair the LED Light
3
COMPONENTS AND STRUCTURE
Model
Weight
Dimensions(LxHxW)
DIMENSIONS
1.79 kg / 3.94 lb
260x315x183mm/10.23x12.4x7.20 in
LEB50E
Beam Angle
Luminaire Location
120°
-20-40°C/-4°F-104°F
SUITABLE FOR WET LOCATIONS
SPECIFICATIONS
Model
CCT
CRI
LEB50E
Input Current
Rated Power
Luminous Flux
0.55A
50W
4500lm
2700-6500K
Input Voltage
100-240V~50/60Hz
Power Factor
≥0.9
≥80
LEB50E
Product Manual
LED WORK LIGHT
LED WORK LIGHT
MODEL: LEB50E
1. Cover
2. LED Light Source
3. Lamp Bracket
3
2
1
5
HOW TO OPERATE THE APP
9
L
70
B
50
lifetime
30000hours L
70
B
50
@25°
t
a
WARNING: INSTALLING THIS LIGHT IN AN UNGROUNDED
ELECTRICAL SYSTEM MAY CAUSE THE METAL PARTS OF
THE LIGHT TO CARRY CURRENT IF ANY WIRES OR WIRE
CONNECTIONS ARE DAMAGED OR LOOSE. IN THIS CASE,
ANYONE WHO TOUCHES THE LIGHT WILL RECEIVE AN
ELECTRIC SHOCK, RESULTING IN INJURY OR DEATH.
BE CAREFUL NOT TO DAMAGE OR CUT THE WIRE
INSULATION (COVERING) DURING INSTALLATION. DO NOT
LET THE WIRES TOUCH ANY SHARP EDGES.
8
PREPARATION
7
FCC Warning:
FCC ID:2AT7E-LEB50E
WARNING:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH
THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF
THE PRODUCT AND THE HAZARDS INVOLVED.
RISK OF SHOCK- BEFORE BEGINNING INSTALLATION,TURN
OFF ELECTRICITY AT THE CIRCUIT BREAKER BOX OR THE
MAIN FUSE BOX.
CAUTION:
PLEASE MAKE SURE YOUR WALL SWITCH AND POWER AT
MAIN CIRCUIT BREAKER BOTH ARE OFF.
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT
A LICENSED ELECTRICIAN.
Any Changes or modifications not expressly approved by the party responsible for compliance could
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
(2) this device must accept any interference received, including interference that may cause
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
STEP 1:
Put the bracket onto the preparedmounting hole and then
screw on.
STEP 2:
Unbind the wire and put the plug into the socket; Press the
ON/OFF button and then LED work light works.
INSTALLATION STEPS
Check all components for damage, do not use the product if
it is damaged.
Product appearance may vary from image shown.
Step 3: Please turn on the Wi-Fi and Bluetooth before connecting LED lights to the
“SMART LIFE” APP.
Tap "+" button on top right corner to add device, then tap"lighting device" to enter next page.
Step 2: Enter the "SMART LIFE" App. and register an account and log in. If you already have
an account for SMART LIFE App., Please select "Log in with existing account".
Step 1: "SMART LIFE" App Download.
There are 2 options for obtaining and downloading
the "SMART LIFE" App on your smart device.
1. Scan the QR code on the right.
2. Search for "SMART LIFE" in the App Store or
Google Play.
1. Power up the LED light.
2. Quickly turn the light off
and on 3 times until it
flashes or breathes.
3. Tap "Next" to enter the
pairing step.
Here you can choose
the color of the light
and adjust the brightness.
Here you can
choose different
lighting modes.
Here you can
choose the sound/
voice control mode.
Here you can set
schedules for the
light or apply other
functions.
4. Tap "+" to add the
LED light.
6. You can tap " " to
change the device
name.
7. Tap "Done" to enter
the control panel.
5. Tap "Next" to complete
the light pairing.
Turn ON/OFF the Smart LED Light three times until the LED Light starts to flash quickly,
which indicates the success of the factory reset.
NOTE:
Choose
color
temperature
Choose
lighting
color
Choose
brightness
(US) 2m(6.56ft)
3 x 18 AWG
H
L
W
1 2
Manufacturer/Hersteller:
Shen Zhen Shi Zhi Hui Duo Ke Ji You Xian Gong Si
qian wan yi lu 1 hao A dong 201 shi, qian hai shen gang he zuo qu, shen
zhen, guang dong, 518000, CN
support@olafuslife.com www.olafuslife.com
69 Aberdeen Avenue, Cambridge CB2 8DL,
United Kingdom | support@olafuslife.com
Made in China
EU REP MDH LIGHTING LTD
Suite 302, 292 Strovolos Avenue, 2048 Strovolos
Nicosia, Cyprus | support@olafuslife.com
UK REP MDH LIGHTING LTD
PARTS LIST
Screw
QTY: 1
Bracket
QTY: 1
B
A
Hex Screw Key
QTY: 1
C