Installation Guide

ManualsBrandsOld Mill Brick ManualsBuilding materialsRushmore Colonial Collection Thin Brick Corners

Items Included in Kit

Items you will need:

- Old Mill Thin Brick

- Mortar (Type S)

- Screw Gun

- Mixing Bucket

- Gloves

- 4ft. Level

- Stiff Bristled Brush

- Wet Tile Saw or Angle

Grinder

1 - Grout Bag for

Applying Adhesive

6 - 5 lb. bags of Adhesive

1 - Mortar Joint Tool

7 - Old Mill Panel

75 - Old Mill Panel

Fasteners & Screws

pg. 1 - Panel Application

Index:

Steps:

Steps: 9 10a 10b

Caution: Take necessary precautions to avoid spills and dust

contamination. Cover flooring, electronics and other items that

are in the area.

Contains Portland cement. Wear rubber gloves

and eye protection. Avoid eye contact or prolonged contact

with skin. Wash thoroughly after handling. If eye contact

occurs, flush with water for 15 minutes and consult physician.

KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE

INTERNALLY. STORE IN A COOL, DRY AREA.

Warning: This product contains one of more chemicals known

to the state of California to cause cancer. Warning: Do not

breathe dust! This product contains Crystalline Silica which may

cause cancer or delayed lung injury (Silicosis). Avoid creation

of dust from this product whenever possible. Wear a NIOSH

approved respirator if creation of dust is unavoidable, or when

working in dust areas.

Installation Guide

pg. 3 - Applying Thin Brick

pg. 2 - Adhesive Application

Grouting

Summary of content (4 pages)

PAGE 1
Installation Guide Items Included in Kit Index: pg. 1 - Panel Application Steps: 1 2 7 - Old Mill Panel pg. 2 - Adhesive Application Steps: 3 4 5 6 pg. 3 - Applying Thin Brick Steps: 7 8 Grouting Steps: 9 75 - Old Mill Panel Fasteners & Screws 1 - Grout Bag for Applying Adhesive 6 - 5 lb. bags of Adhesive 1 - Mortar Joint Tool 10a 10b Items you will need: - Old Mill Thin Brick Mortar (Type S) Screw Gun Mixing Bucket Gloves 4ft.
PAGE 2
Panel Application 1 Begin by positioning Old Mill Panel on the bottom corner of your wall. Level the panel using a 4 foot level (pic 1). (pic 1) When installing brick that is ground level, you must remove the bottom row of foam panel (about 1.5 in.). This ensures that the bottom row will be a full brick. *Note: THIS IS ONLY FOR THE BOTTOM ROW OF PANELS. Wall Thin Brick Cut 2 Floor Once level, attach the panel with the Old Mill washers and exterior grade screws (pic 2).
PAGE 3
Adhesive Application 3 There are six 5 lb. bags of adhesive in your kit. Use one at a time to avoid loss of material. Place 2 ¼ cups of water in a small bucket and then empty in one 5 lb. bag of adhesive (pic 3). Take necessary precautions to avoid spills. (pic 3) 4 Thoroughly mix using a margin trowel or small mixer until you have reached a consistency similar to icing. Let stand for 8 minutes. (THIS IS CRITICAL. NOT ALLOWING THIS TIME COULD PRODUCE POOR ADHESION.) Mix again for 1 minute (pic 4).
PAGE 4
Applying Thin Brick 7 If you have corners, apply brick to those areas first. Next, install two full rows across the top; this will set your pattern. To install brick, place the bottom edge of the brick against the upper edge of the brick spacer. Press the brick into place by applying pressure up and in on the brick (pic 7). *Note: Brick should be cut using a wet tile saw as to avoid dust.