Use and Care Guide

Sakrete.com • 866-725-7383
The Pro’s Choice Since 1936
DIVISION 4
Masonry Mortaring – 04 05 13
Color: Gray
Preparation/Application:
For best results all materials should be stored between 40
0
F (4
0
C) and 80
0
F
(27
0
C) 24 hours prior to installation.
Refer to:
- ACI 530.1 Specification for Masonry Structures
- International Masonry Industry All-Weather Council (IMIAC)
• Recommended Practices and Guild Specifications for Cold Weather
Masonry Construction
• Recommended Practices and Guide Specifications for Hot Weather
Masonry Construction
NOTE: it is the responsibility of the installer/applicator to ensure the suitability of the product for its
intended use.
New Construction:
When laying brick or block, construct a sound footing above grade. Consult with
your local building codes before proceeding. For more information visit
Sakrete.com
1. Apply a full bed of mortar onto the base where the brick or block will be
placed.
2. When laying brick or block butter the end with mortar before placing into the
full bed of mortar.
3. Tap into place while leveling.
4. Tool joints once the mortar has set up enough and is thumb print hard.
Tuck Pointing:
1. Place mortar into the joint with a tuck pointing trowel or grout bag.
2. Use the tuck pointing trowel to tool the joint and compact for a tight neat
appearance.
Scratch/Brown/Stucco:
1. Application over masonry must follow ASTM C926 Standard Specification
for Application of Portland Cement Based Plaster.
2. Applications over lath must follow ASTM C1063 Standard Specification for
Installation of Lathing and Furring to receive interior and exterior Portland
cement based plaster.
3. Apply material using a trowel and masonry hawk using enough pressure to
compact the material.
4. Texture stucco to match the surrounding area using a plasterer’s trowel or
finish to desired texture.
NOTE: Check with local building code requirements for proper installation guidelines.
Mixing:
1. Empty contents of Sakrete Type N Mortar Mix into a wheelbarrow or
mortar pan forming a crater in the center of the dry mix for the addition of
clean potable water. Projects requiring multiple bags are mixed much easier
with a mechanical mixer.
Mortar Mix Type N
Sakrete
®
Type N Mortar Mix is a preblended
mixture of sand and masonry cement or
sand, lime and portland cement. For laying
brick, block and stone in load bearing walls.
Build walls, planters, and chimneys. For tuck
pointing or repairing existing mortar joints.
Can also be used for scratch and brown
coat in stucco applications. Meets property
requirements of ASTM C270 and C1714.
Features:
• Strength >750 psi
• Meets property requirements of ASTM C1714 and ASTM C270
• Applications from 1/4” (6.4 mm) to 1/2” (13 mm)
• Can be color pigmented with the Sakrete Cement Colors
Use For:
• Laying brick or block
• Scratch and brown coat in stucco
• Above grade applications
• Interior or exterior
• Brick and block tuck pointing
Yield/Water/Coverage:
NOTE: Yield and water are approximate. The yield above does not allow for
waste and spillage.
Technical Data:
Compressive Strength ASTM C270 28 day= >750 psi
Water Retention > 75%
Mortar should be tested in the field by ASTM C780, standard test method for
preconstruction & construction evaluation for mortar for plain and reinforced
unit masonry. Due to the procedure differences between ASTM C270 and ASTM
C780, the compressive strength values resulting from field sampled mortar are
not required nor expected to meet the minimum compressive strengths of the
property specifications of ASTM C270 as tested in controlled laboratory condi-
tions.
Bag Size Yield: For laying brick,
block, or cultured stone
Yield: For stucco Water
40 lb
(18.1 kg)
Will lay 6 = 8” (200 mm)
concrete block, 18 standard
bricks or 5 ft
2
(0.5 m
2
) of
cultured stone
Will cover 35 ft
2
(3.3 m
2
) at 1/8”
(3.2 mm) thick
2.6 qt
(2.5 L)
60 lb
(27.2 kg)
Will lay 9 = 8” (200 mm)
concrete block, 26 standard
bricks or 7.5 ft
2
(0.7 m
2
) of
cultured stone
Will cover 50 ft
2
(4.3 m
2
) at 1/8”
(3.2 mm) thick
4.0 qt
(3.8 L)
80 lb
(36.3 kg)
Will lay 12 = 8” (200 mm)
concrete block, 35 standard
bricks or 10 ft
2
(1.0 m
2
) of
cultured stone
Will cover 70 ft
2
(6.4 m
2
) at 1/8”
(3.2 mm) thick
5.3 qt
(5 L)