User Manual for Oliso™ Steam Iron with Auto-Lift System™ Models TG-800 with Non-Stick Soleplate TG-1000 with Stainless Steel Soleplate Safer. Smarter. Simpler.
IMPORTANT SAFETY INSTRUCTIONS When using your iron, basic safety precautions should always be followed, including the following: Read all instructions before using this product. 1 ) Use iron only for its intended use. 2 ) To protect against a risk of electric shock, do not immerse the iron in water or other liquids. 3 ) The iron should always be turned to “Off” before plugging or unplugging from the outlet. Never yank cord to disconnect from the outlet; instead, grasp plug and pull to disconnect.
Welcome Thank you for purchasing the Oliso™ Iron, the only iron with the patented AUTO-LIFT SYSTEM™. You’re just a few steps away from a new safer, easier way of ironing. Follow the instructions in this manual to learn about your new iron’s features and care. We hope you enjoy your Oliso™ Iron. Smart. Simple. Delightful.
3 simple steps to start 1 2 FILL SET UP Open the Flip Funnel™ and add water to the tank with the fill cup or directly from a faucet. Plug in, then choose a fabric setting.
3 IRON Enjoy your Oliso™ iron If you would like to learn more about your iron’s unique features, please read on. When the green light stops blinking and is constantly lit, the iron is ready for use. Touch the handle and begin.
getting to know your Oliso™ iron Status Light Steam Button Spray Button Touch-activated handle Steam Selector Electronic Fabric Selector Auto-Lift™ on/off switch Drain Spout Flip Funnel™ Water Tank Spray Nozzle Detailer Lifters Soleplate - non-stick (TG-800) - stainless steel (TG-1000)
Auto-Lift System™ To operate, place the iron right side up on a flat surface. Plug the iron into an outlet and make sure the Auto-Lift switch is in the on ( ) position. Touch the iron handle and the iron will sense your hand and lower. Let go and the iron’s Lifters will automatically raise the iron above fabric. overriding the Auto-Lift system™ If you wish to turn off the Auto-Lift system, move the switch on the back of the iron to the off ( ) position. Your iron will now operate like a standard iron.
water tank Before filling, slide the steam selector to off ( ). Make sure the iron is unplugged. Open the Flip Funnel™. Leave the iron in a horizontal position and fill using the included fill cup. Two fill cups equal the maximum capacity of the water tank. Alternatively, fill directly from a faucet holding the iron horizontally. Do not fill the tank past the MAX fill line on the side of the iron. Close the port when done.
fabric selector steam ok temperature is too low for steam fabric selector Turn the fabric selector to select a fabric setting. To use constant steam or steam burst, the temperature must be set to the wool, cotton, or linen range. red flashing green green flashing red off heating or cooling at set temp auto off The Oliso iron uses a status light to display the iron’s status. To ensure correct temperature, wait until the light displays steady green before ironing.
steam/spray system Steam Selector: Slide the steam selector to set the amount of constant steam. The iron can only produce steam when the fabric selector knob is set to the wool ( •• ), cotton, or linen range (•••). Allow the iron to heat up (steady green status light) before activating the steam control. Steam will be produced as soon as the iron is lowered. Dry Ironing: To turn off the steam, slide the steam selector off ( ).
auto shut-off system If the Oliso™ iron is not being used while it is plugged in, the status light will flash red and the iron will turn itself off. The auto shut-off timing depends on whether the Auto-Lift System™ is turned on or off. Touch the handle of the iron to restart it.
after ironing a. Turn the fabric selector to off. Slide the steam selector to off ( d. ). b. Unplug the appliance (Do not hold iron while unplugging or the Lifters will not stay extended. Iron should always be stored with Lifters extended to prevent leaking). c. Place iron on the Lifters and allow to cool. d. Important: Empty water from the water tank after use. Tilt the iron forward to drain from the spout at the front of the iron. To drain faster, open the Flip Funnel™ . e. e.
trouble shooting guide problem things to check fabric selector is set to off iron does not heat Lifters do not come out iron does not steam Check to make sure the plug is fully plugged into the socket. auto shut-off system is activated touch the handle. Auto-Lift switch set to off Set the switch on the back of the iron to the on ( iron not plugged in correctly Check to make sure the plug is fully plugged into the socket.
One (1) Year Limited Warranty Oliso, Inc. warrants that for a period of one year from the date of the original purchase, this product will be free from defects in material and workmanship, when utilized for normal household use. Oliso, Inc. will repair or replace this product or any component of the product found to be defective during the warranty period without charge to the customer. If a replacement product is sent, it will carry the remaining warranty of the original product.
For product questions: Oliso Customer Service customerservice@oliso.com www.oliso.com 1.800.899.5157 © 2005 Oliso, Inc. All rights reserved. Touch&Glide™, Auto-Lift System™, Auto-Lift™, Flow Glide™, Flip Funnel™, and Smart Touch™ are trademarks of Oliso Inc. Printed in China U.S. Patent No.
Thanks for shopping Oliso! Visit www.oliso.com/registration.html to register your iron or www.oliso.
