&
IMPORTANT SAFETY INSTRUCTIONS When using your flatiron, basic safety precautions should always be followed, including the following: Read all instructions before using this product. 1 ) Use iron only for its intended use. 2 ) To protect against a risk of electric shock, do not immerse the iron in water or other liquids. 3 ) The iron should always be turned to “Off” before plugging or unplugging from the outlet. Never yank cord to disconnect from the outlet; instead, grasp plug and pull to disconnect.
Welcome Thank you for purchasing the Oliso Touch&GlideTM iron. You’re just a few steps away from a whole new way of ironing. Follow the instructions in this manual to learn about your new iron’s features and care. We hope you enjoy your Oliso Touch&GlideTM.
3 simple steps to start 1 2 FILL SET UP Open the Flip Funnel and add water to the tank with the fill cup or directly from a faucet. TM Plug in, then choose a fabric setting.
3 IRON Enjoy your Touch&Glide ! TM If you would like to learn more about your iron’s unique features, please read on. When the blinking green light becomes steady, touch the handle and iron.
getting to know your iron status light steam button spray button Smart Touch handle TM steam selector Auto-Lift override switch TM electronic fabric selector knob drain spout Flip Funnel TM water tank spray nozzle Flow Glide soleplate TM Auto-Lift spacers TM
Auto-Lift system TM To operate, place the iron on its soleplate on a flat surface. Plug the iron into an outlet and make sure the Auto-Lift switch is in the on ( ) position. Simply touch the iron handle and the iron will sense your hand and lower. Any time you release the handle the spacers will automatically raise the iron to protect your fabric. TM overriding the Auto-Lift system TM If you wish to turn off the Auto-Lift system, move the switch on the back of the iron to the off ( ) position.
water tank Before filling, slide the steam selector to off ( ). Make sure the iron is unplugged. Open the Flip Funnel . TM Leave the iron in a horizontal position and fill using the included fill cup. Two fill cups equal the maximum capacity of the water tank. Alternatively, fill directly from a faucet holding the iron horizontally. Do not fill the tank past the MAX fill line on the side of the iron. Close the port when done.
fabric selector temperature is too low for steam steam ok Turn the grey fabric selector knob to select a fabric setting. To use constant steam or steam burst, the temperature must be set to the cotton/linen range (•••). fabric selector knob red flashing green green flashing red off heating or cooling at set temp auto shut-off The Touch&Glide iron uses a status light to display the iron’s status. To ensure correct temperature, wait until the light displays steady green before ironing.
steam/spray system Steam Selector: Slide the steam selector to set the amount of constant steam. The iron can only produce steam when the fabric selector knob is set to the cotton or linen range (•••). Allow the iron to heat up (steady green status light) before activating the steam control. Steam will be produced as soon as the iron is lowered. Dry Ironing: To turn off the steam, slide the steam selector off ( ).
auto shut-off system If the Touch&Glide iron is not being used while it is plugged in, the status light will flash red and the iron will turn itself off. The auto shut-off timing depends on whether the Auto-Lift system is turned on or off. The iron will return to normal operation once you resume ironing.
after ironing a. Turn the fabric selector knob to off. Slide the steam selector to off ( ). b. Unplug the appliance (Do not hold iron while unplugging or the Auto-Lift spacers will not stay down). TM d. c. Place iron on the Auto-Lift spacers and allow to cool. TM d. Important: Empty water from the water tank after use. Tilt the Touch&Glide forward to drain from the spout at the front of the iron. To drain faster, open the Flip Funnel . TM TM e. e.
trouble shooting guide PROBLEM iron does not heat THINGS TO CHECK fabric selector knob is set to off turn the fabric selector knob to a fabric setting. iron not plugged in correctly check to make sure the plug is properly seated in the socket. auto shut-off system is activated touch the handle. Auto-Lift switch set to off set the switch on the back of the iron to the on ( iron not plugged in correctly check to make sure the plug is properly seated in the socket.
One (1) Year Limited Warranty Oliso, Inc. warrants that for a period of one year from the date of the original purchase, this product will be free from defects in material and workmanship, when utilized for normal household use. Oliso, Inc. will repair or replace this product or any component of the product found to be defective during the warranty period without charge to the customer. If a replacement product is sent, it will carry the remaining warranty of the original product.
For product questions: Oliso Customer Service customerservice@oliso.com www.oliso.com 1.800.899.5157 c 2005 Oliso, Inc. All rights reserved. Touch&GlideTM, Auto-LiftTM, Flow GlideTM, Flip FunnelTM, and Smart TouchTM are trademarks of Oliso Inc. Printed in China U.S. Patent No.