INSTRUCTIONS
EDITED/PUBLISHED/PRODUCED BY: Printed in Thailand. Olivetti S.p.A. con unico azionista Gruppo Telecom Italia Direzione e coordinamento di Telecom Italia S.p.A. Code of user manual: 256679S-02 Date of publication: July 2007. Copyright © 2006, Olivetti All rights reserved. No parts of this manual may be photocopied, reproduced or translated into other languages without prior written authorization from Olivetti S.p.A.
TABLE OF CONTENTS - FIRST SECTION BEFORE YOU START 3 CONSULTING THE MANUAL ....................................................... 3 ENVIRONMENTAL RECYCLING ................................................... 3 SAFETY PRECAUTIONS .............................................................. 3 ABOUT THE INSTALLATION AND SETUP PARAMETERS ........... 4 ABOUT THE FAX MACHINE 5 CONSOLE ..................................................................................... 5 COMPONENTS .......................
BEFORE YOU START CONSULTING THE MANUAL This manual describes various models of fax machine which differ from one another not only in the graphic appearance of their operator console but also in whether or not they have a built-in telephone answering device. In the description that follows, whenever a distinction is to be made between these models, reference will be made to: "Base models" and "Models with a built-in TAD".
OPERATING • • • • • • • PRECAUTIONS Keep the fax machine in a dust-free place away from sources of water, steam and excessive heat. Do not expose it to direct sunlight. Ensure that no books, documents, or other objects obstruct normal ventilation in any way. Use the fax machine exclusively at a temperature of between 5°C and 35°C and a relative humidity of between 15% and 85%. Keep the fax machine away from other electrical and electronic appliances that may cause interference, e.g.
ABOUT THE FAX MACHINE CONSOLE "Error" LED indicator Signals an operating fault during transmission or reception. • After the button has been pressed, it turns the speaker volume "up" or "down". Display A two-line liquid crystal display with a capacity of 16 characters per line. Shows operator prompts and error messages. • They scroll cyclically forwards or backwards through the functions and related parameters on the menu.
• • Adjusts the resolution of the documents to be sent and copied (only with the document inserted in the ADF). • Gives access to the Phone book. Puts the line on hold during a telephone conversation (with the handset raised). • Unloads a document from the ADF. • Turns off the " • Returns the fax machine to the stand-by mode. • Stops the programming, transmission, reception or copying operation in progress. • Deletes incorrect settings from the display.
COMPONENTS The figure shows the external and internal parts of fax machine. PAPER SUPPORT EXTENSION CONNECTION SOCKETS PLAIN PAPER FEED COMPARTMENT (ASF) Maximum capacity: 40 sheets (80gr/m2). AUTOMATIC FEEDER FOR DOCUMENTS TO BE SENT AND COPIED (ADF) MAXIMUM CAPACITY: 5 SHEETS OF A4 SPEAKER BUILT-IN OPERATOR CONSOLE TELEPHONE HANDSET DISPLAY RECEIVED OR COPIED DOCUMENT OUTPUT The display consists of two lines of 16 characters each.
HOW TO GET STARTED QUICKLY This section provides a basic description of the fax machine, explaining how to install it and get started quickly, using its basic functions only. For a more comprehensive use of the fax machine, see the corresponding section. As this section is designed to give you a gradual and systematic approach to the fax machine, we recommend you read the topics in the order in which they are presented. PACKAGE CONNECT 1.
CONNECT THE If your country is not present among those shown on the display, see the table below: FAX MACHINE TO THE POWER SUPPLY COUNTRY Argentina Australia Austria Belgium Brazil Chile China Colombia Denmark Finland France Germany Holland Ireland Italy Luxembourg Mexico Norway Peru Portugal Rest of world Spain Sweden Switzerland UK Uruguay Venezuela 1. A. Insert the female connector at one end of the power cable into the male connector on the rear of the fax machine. a b B.
TO SET THE DATE AND TIME FOR THE FIRST TIME The first time you connect the fax machine to the power supply or whenever there is a power failure you must set the date and time as described below. The date and time will be printed at the top of all documents sent and will be shown on the display when the fax is in stand-by mode. Once set, the date and time can be changed at any time. You can also modify the format in which they are shown on the display, see "To change the date and time".
notE TO If you have chosen the "SET DATE/TIME" option, proceed as follows: 1. Enter the new date and time (e.g. 13-Jan-06; 18:00), by pressing the keys: - . As each digit is entered, the cursor will move to the next one. 2. If you wish to move the cursor to digits to be modified, press the keys: |/}. 3. Then overwrite the digits with the correct ones, by pressing - . the keys: . 4. To confirm the setting, press the key: 5. To return the fax machine to its initial stand-by mode, press the key: . . 6.
To modify the dialling mode: 1. Press the key: ALL THAT IS MISSING NOW IS YOUR NAME AND FAX NUMBER The display shows: MENU RECEPT. SET-UP Once set, the name (max. 16 characters) and number (max. 20 digits) will remain unchanged until they are intentionally changed and will be printed on each page received by your correspondent's fax machine. 1. Press the key: 2. Press the keys until the display shows: The display shows: MENU INSTALLATION MENU RECEPT. SET-UP 3. Press the key: 2.
14. To delete the whole name, hold down the key: For example, to enter the name "LARA": Until you have selected the letter "L". Until you have selected the letter "A". Until you have selected the letter "R". Until you have selected the letter "A". 15. To confirm the name, press the key: The display shows: INSTALLATION STATION NAME Now enter the fax number as indicated below: To set your fax number: 1. Press the keys: The display shows: INSTALLATION STATION NUMBER 2.
10. To return the fax machine to its initial stand-by mode, press the key: 1. Lower the handset and place it on a stable surface. 11. If you want to move back one function, press the key: SETTING UP THE FAX MACHINE FEED 2. Open and lift the operator console as indicated by the arrows. THE PRINT PAPER INTO THE MACHINE 1 1. Push the paper support extension in the slot until it clicks into position. 2.
Examine the print test sheet as follows: 1. Check that the numbered scale is not broken at any point and that the black areas do not present any horizontal white lines: if these conditions, which confirm that the cartridge has been inserted correctly and is working properly, are respected, set the value 1. The fax machine returns to its initial stand-by mode and is ready for use.
TO RECEPTION SEND A DOCUMENT 1. If these diagrams are not enough, see "To send a document", section "Transmission and reception operations". You can set up the fax machine to receive the documents sent by your correspondents in four different modes, that you may access by carrying out the procedure described below. These modes are: manual reception, automatic reception, automatic reception with recognition of the type of call and reception with telephone answering device.
MANUAL RECEPTION IN "PHONE/FAX" RECEPTION For all occasions in which you are present and you can therefore answer the calls yourself. 1. If these diagrams are not enough, see "To receive a document", section "Transmission and reception operations". MODE The behaviour of the fax machine in this mode depends on who is calling and whether you are in or not when the fax is received. The following diagram will help you: After the programmed number of rings. PHONE/FAX enabled. A FAX MACHINE is calling.
USING THE TELEPHONE TO Do not place the document in the ADF. 1. Press and hold down for more than one second the number key (0-9) under which you saved previously the telephone number you wish to call, for example, When you engage the line by lifting the telephone handset, you may use all the telephone functions available on ordinary telephones sold on the market.
8. To confirm your choice, press the key: MAKING COPIES The display shows: WHAT ZOOM 100% DOCUMENTS CAN BE COPIED As for transmission, copying requires the document to be inserted in the automatic document feeder (ADF). Before making a copy, make sure that the document is correctly inserted in the feeder and that it respects the characteristics described previously (see the "Transmission" section).
TABLE OF CONTENTS - SECOND SECTION TRANSMISSION AND RECEPTION OPERATIONS 23 MAINTENANCE OPERATIONS 58 TO SEND A DOCUMENT ............................................................ 23 TO REPLACE THE PRINT CARTRIDGE .................................... 58 TO RECEIVE A DOCUMENT ....................................................... 27 CLEANING THE PRINT CARTRIDGE AND TESTING THE NOZZLES ............................................................................ 59 PHONE BOOK .......................
TRANSMISSION AND RECEPTION OPERATIONS TO SEND A DOCUMENT WHAT A B 2. Place the document in the auto- matic document feeder (ADF) with the side to be sent face down (A). DOCUMENTS MAY BE USED Place the document against the right-hand side of the feeder: see the mark printed on the fax machine's casing (B). Dimensions • • Width Length 210 mm min. 105 mm - max. 600 mm • Unit weight 70 - 90 gr/m2 (max.
6. Press the keys TO SEND A DOCUMENT until the display shows: 1. Insert the document in the automatic document feeder (ADF). The display shows on the top line: VARIOUS SETT. CONTRAST 7. Press the key: DOCUMENT READY and on the bottom line, the default contrast value: "NORMAL". The display shows: CONTRAST The initial resolution value is: " NORMAL 8. To view the other available options, "CONTRAST DARK" and "CONTRAST - LIGHT", press the keys: 9. To confirm your choice, press the key: " (standard).
2. To hear the dialling tones, press the key: AUTOMATIC REDIAL The display shows: ON LINE and the length of the transmission in minutes and seconds in the top right-hand corner. If no connection is established due to line errors or because the correspondent’s number is busy, the fax machine automatically redials the number of times laid down by the legislation in your country. 3. To dial the number of the correspondent to whom you wish to send the document, press the keys: TO 4.
7. To confirm both the current time and the time set in step 6, press the key: The display shows: TYPE NUMBER 8. Type your correspondent's number directly on the numeric keypad, by pressing the keys: note If there is a power failure, the transmission from the memory will be cancelled. TO CHANGE/REPEAT/DELETE A TRANSMISSION FROM THE MEMORY THAT IS ALREADY SET 9. If you like, you can find your correspondent's number in the phone book (see "To program the phone book"). 1.
TO RECEIVE A DOCUMENT You can set up the fax machine to receive the documents sent by your correspondents in four separate modes: • Manual reception, for all occasions in which you are present and you can therefore answer the calls yourself. • Automatic reception, for all occasions in which you are out but want to receive documents anyway. This is the mode originally set on your fax machine. Automatic reception with recognition of the type of call.
note 8. To leave a space, to correct typing mistakes or to enter characters or special symbols, proceed as explained in "All that is missing now is your name and fax number", chapter "How to get started quickly". 9. To confirm the setting, press the key: Any kind of reception may be stopped by pressing the key. The fax machine then returns to its initial stand-by mode.
6. To find the telephone number or name you want to modify, you can: 8. To choose the other option, "DELETE? - YES", press the keys: 1. Press the keys until the desired number or name appears on the display. or 2. Press the key bearing the first letter of the name you are looking for. The fax machine will search for the name in alphabetical order. 9. To confirm the setting and delete the number, press the key: The display shows: PHONE BOOK 7.
TO SEND A TO PRINT REPORTS AND LISTS DOCUMENT USING THE PHONE BOOK SEARCH FUNCTION If you can't remember the position with which you associated a given number, you can send the document from the phone book as follows: 1. Insert the document in the automatic document feeder (ADF). The display shows on the top line: DOCUMENT READY and on the bottom line, the default contrast value: NORMAL. The initial resolution value is: " " (standard).
• Remote Id • Date/Time • Duration • Pages • Result 7. Press the key: Number (and, sometimes, name) of the correspondent called. This number corresponds to the number you dialled, only if the correspondent set his own fax number correctly. Otherwise, it may be different or not be present at all. Date and time at which the transaction was carried out. Length of transaction (in minutes and seconds). Total number of pages sent/received.
4. Press the keys LISTS until the display shows: FAX SET-UP At any time, you can print a complete list of the installation parameters, set-up parameters and disabled numbers as well as print the data saved in the phone book. By printing out the lists of installation and setup parameters, you will obtain an up to date report of the default values and those that you have set to adapt it to your operating requirements. TO PRINT THE LIST OF INSTALLATION PARAMETERS PRINT CONFIG. 5.
THE TELEPHONE ANSWERING DEVICE If you have purchased one of the models of fax equipped with a built-in telephone answering device you can perform the same functions as those performed by external telephone answering devices.
9. To return the fax machine to the initial stand-by mode, press the key: SECURITY AND ACCESS FUNCTIONS To operate the TAD from a remote location (except to leave messages), you must set a four-digit numeric code which you can change or delete at any time (see "To change/delete the TAD access code").
10. To return the fax machine to the initial stand-by mode, press the key: 11. If you want to move back one function, press the key: TO OUTGOING MESSAGES AND MEMOS You can record several different types of outgoing messages: • OGM 1, which has a maximum length of 20 seconds, prompting the caller to leave a message on the TAD, for example: "You have called the telephone number ... I’m out at the moment.
7. Press the key: 6. To listen to message 1 recorded previously, press the key: The display shows: The display shows: LIFT HANDSET PLAYING 8. Lift the handset. The display shows: <|> TO RECORD 9. To start recording the message, press the key: You have 20 seconds (counted on the display) to record • your message: if the message lasts less than 20 seconds, when you reach the end of the message hang up or press the key or the • key.
notE 3. Press the key: The display shows: TAD SET-UP ICM ON SPEAKER You have 30 or 60 seconds at your disposal (see "To set the length of memos and incoming messages") to record your memo in the same way as OUTGOING MESSAGES 1 and 2. 4. Press the keys until the display shows: TAD SET-UP TO SET THE LENGTH OF MEMOS AND INCOMING MESSAGES OGM 2 5. Press the key: 1. Press the key: The display shows: OGM 2 PLAY 6. Press the keys until the display shows: OGM 2 DELETE 7.
TO LISTEN TO INCOMING MESSAGES AND 2. To delete the message you are listening, press the key: The TAD moves to the next message and the display shows: MEMOS PLAY MSG 01 02 If there is one or more incoming messages or memos in the memory of the telephone answering device that have (MESSAGES) LED not yet been played back, the indicator blinks and the display shows the total number of messages recorded (including the memos), for example, 03: TAD/FAX 01-Feb-06 10:32 3.
CODE 1 2 3 4 5 6+6 CODE #1 #2 #3 #4 OPERATING FUNCTION SPECIAL FUNCTIONS OF THE TELEPHONE Plays new messages. Plays all messages. Stops playing current message and returns to previous message. Stops playing current message and skips to next message. Playing outgoing message 1. Deletes all played messages.
7. To confirm the setting, press the key: 7. To confirm the setting, press the key: The display shows: OGM 1 8. To return the fax machine to the initial stand-by mode, press the key: RECORD 8. To confirm the setting, press the key: 9. If you want to move back one function, press the key: The display shows: RECORD OGM 1 LIFT HANDSET OUTGOING MESSAGE ONLY Using this function, whenever an incoming call is received, the TAD plays the OGM 1 but does not record any incoming messages.
6. To confirm the setting, press the key: 7. To return the fax machine to the initial stand-by mode, press the key: 8. If you want to move back one function, press the key: TO PRINT THE TAD CONFIGURATION PARAMETERS 1. Press the key: The display shows: MENU RECEPT. SET-UP 2. Press the keys until the display shows: MENU TAD SET-UP 3. Press the key: The display shows: TAD SET-UP ICM ON SPEAKER 4. Press the keys until the display shows: TAD SET-UP PRINT SET-UP 5.
MORE SOPHISTICATED OPERATIONS OTHER USEFUL RECEPTION SETTINGS TO RECEIVE A DOCUMENT THAT IS LONGER THAN THE PAPER SIZE USED TO REDUCE THE AREA OF A DOCUMENT RECEIVED 1. Press the key: The display shows: MENU RECEPT. SET-UP 2. Press the keys until the display shows: MENU FAX SET-UP 3. Press the key: The display shows: FAX SET-UP DATE AND TIME 4. Press the keys until the display shows: FAX SET-UP PRINTER PARAM. 5. Press the key: The display shows: PRINTER PARAM. REDUCTION 6.
7. To return the fax machine to its initial stand-by mode, press the key: 11. If you want to move back one function, press the key: 8. If you want to move back one function, press the key: NOTE If you choose the "SURPLUS - AUTOMATIC" setting, the fax machine will print the surplus text on another sheet providing the surplus exceeds 12 mm. If you choose the "SURPLUS - YES" setting, the fax machine will always print the surplus text on another sheet.
1. Press the key: 3. Press the key: The display shows: The display shows: MENU INSTALLATION RECEPT. SET-UP STATION NAME 2. Press the key: 4. Press the keys The display shows: until the display shows: INSTALLATION RECEPT. SET-UP TEL.LINE SETUP RECEPTION MODE 3. Press the keys 5. Press the key: until the display shows: The display shows: RECEPT. SET-UP TEL.LINE SETUP RINGS NUMBER LINE TYPE 4. Press the key: 6. Press the keys The display shows: until the display shows: TEL.
4. Press the key: The display shows the preset volume level, for exam- 4. Press the keys until the display shows: INSTALLATION ple 4: RING VOLUME LEVEL 4 5. To turn the volume up/down, press the keys: DISTINCT. RING 5. Press the key: The display shows: DISTINCT. RING 6. To confirm your choice, press the key: 7. To return the fax machine to its initial stand-by mode, press the key: SET OPTION 6. To view the other available option, "DISTINCT. RING SET PATTERN", press the keys: 7.
TO 9. To confirm your choice, press the key: CHANGE THE LENGTH OF THE ACOUSTIC SIGNAL This function is only enabled in some countries.
7. Press the key: 4. Press the key: The display shows: The display shows: REMOTE CONTROL BLACK LIST YES NEW NUMBER 8. Press the key: 5. Press the key: The display shows: The display shows the code you set previously, for example: 0:TYPE NUMBER _ SET ACCESS CODE CODE(0/9,*) *8 6. Dial the fax number you wish to inhibit. To do this, press the keys: 9. To type the new code, press the keys: - 10. To confirm the new code, press the key: 7.
9. To view the other available option, "DELETE? - YES", press the keys: 5. Press the keys until the display shows: BLACK LIST MODIFY NUMBER 10. To confirm the setting, press the key: The display shows: 6. To confirm the setting, press the key: BLACK LIST The display shows the first number on the black list. DELETE NUMBER 7. To find the number you wish to modify, press the keys: 11. From this point on, to delete other numbers from the list, repeat the procedure from step 6. 8.
9. To confirm the setting, press the key: OTHER USEFUL TRANSMISSION SETTINGS TO CHANGE THE POSITION OF YOUR NAME 10. To return the fax machine to its initial stand-by mode, press the key: AND FAX NUMBER The information in the heading of the document to be sent (name, fax number, date and time and number of pages) may be received by your correspondent's fax machine outside the text area immediately below the top edge of the sheet or inside the text area, slightly lower down than in the previous case.
8. To view the other available option, "LINE MONITOR YES", press the keys: 4. Press the keys: The display shows: FAX SET-UP 9. To confirm the setting, press the key: VARIOUS SETT. 5. Press the key: 10. To return the fax machine to its initial stand-by mode, press the key: The display shows: VARIOUS SETT. ECM 11. If you want to move back one function, press the key: 6. Press the keys until the display shows: VARIOUS SETT. TO REGULATE THE BUZZER VOLUME SPEAKER VOLUME 7.
3. Press the key: RECEIVING A DOCUMENT IN POLLING MODE The display shows: FAX SET-UP FIRST DATE AND TIME OF ALL, WHAT POLLING IS 4. Press the keys: The display shows: FAX SET-UP VARIOUS SETT. 5. Press the key: It is a transmission request that a fax machine makes to another fax machine so that the latter sends the document requested automatically. There are two main characteristics of communication using the polling method: • the user who is to receive the document requests transmission.
6. To confirm both the current time and the new time, press the key: From this point on, follow the procedure described in "To make a transmission request (polling reception)" from step 5. The display shows: TYPE NUMBER _ 7. Type your correspondent's number directly on the numeric keypad. To do this, press the keys: TO DELETE A POLLING RECEPTION THAT HAS BEEN SET 1. Press the key: The display shows: MENU 8.
TROUBLESHOOTING GUIDE WHAT HAPPENS IF THERE IS A POWER FAILURE If a power failure occurs, the fax machine keeps the following data in the memory: the numbers set in the phone book and the reports, while the documents present in the memory will be lost. The date and time will also be lost so they will have to be reset by carrying out the procedure described in the "To set the date and time for the first time" section of the "How to get started quickly" chapter.
ERROR CODES The error codes printed both on the transmission report and the activity report consist of two digits indicating the cause of the error. To save space, the two-digit code without any message is printed on the activity report. CODE MESSAGE CAUSE OF ERROR WHAT TO DO OK OK Operation performed successfully. No action. 02 IMPOSSIBLE CONNECTION CHECK WITH OTHER PARTY The fax machine does not detect any Check that the fax machine is correctly dialling tone or receives an irregular signal.
SIGNALS AND MESSAGES Any problems that may arise are generally indicated by acoustic signals (accompanied, in some cases, by visual signals : error LED " " indicator on) or by error messages on the display. The fax machine also emits acoustic signals and shows messages on the display, which do not indicate an error condition.
ILLEGAL SETTING POLL.RETRY NNN The date and time have not been set correctly: see "To set the date and time for the first time" and "To change the date and time", in the "How to get started quickly" chapter. You set polling reception and the connection was not established due to line errors or because the correspondent is busy: the fax machine prepares to redial automatically.
DIALLING TRANSMITTING The fax machine is dialling the number of the correspondent you called. A document is being sent. TRANSMITTING... DOC.N. XXXX A document is being sent. You have set a document transmission from the memory and the fax machine has just finished storing the document. "XXXX" corresponds to the number that identifies the document you have just stored. TX COMPLETED Transmission was completed successfully.
MAINTENANCE OPERATIONS Warning! 7. Avoid touching the nozzles. TO REPLACE THE PRINT CARTRIDGE The print cartridge must be replaced, when the ink runs out (used print cartridges cannot be used) or when you notice a deterioration in the print quality. In the former case, the fax machine automatically prints a sheet to remind you that the ink is about to run out and that you should replace it. 8.
6. To view the other available option, "CLEAN CARTRIDGE - YES", press the keys: 3. Press the key: The display shows: CART. MAINTEN. 7. Press the key: NEW CARTRIDGE The fax machine resets the cartridge and tests the noz- 4. Press the key: zles, and then prints out the result of the diagnostic test. To interpret the diagnostic test result correctly, see "Insert the print cartridge" in the "How to get started quickly" chapter. The display shows: NEW CARTRIDGE NO 5.
3. Release the print cartridge by pressing the lever as indicated by the arrow. 2. Open and lift the operator console as indicated by the arrows. 4. Take the print cartridge out of its compartment. 3. Move the print cartridge carriage to the left-hand edge of the fax machine. 5. Clean the electrical contacts using a slightly damp cloth. Warning! Do not touch the nozzles! 4. Release the paper feed roller by pressing the lever, as indicated by the arrow. 6.
127( To check whether the optical reader is clean, make a copy of a blank sheet. If any vertical lines appear on the copy and the optical reader looks perfectly clean, contact qualified technical staff. TO CLEAN THE CASING TO REMOVE JAMMED SHEETS OF PAPER If the paper used to print received documents or to copy documents gets jammed (this error is signalled on the display by the message "PAPER ERROR, PRESS < V >"), try to unload the sheet by pressing the key.
MANUFACTURER AND CUSTOMER SERVICE MANUFACTURER Olivetti S.p.A. con unico azionista Gruppo Telecom Italia Direzione e coordinamento di Telecom Italia S.p.A. Via Jervis, 77 - 10015 IVREA (TO) ITALY CUSTOMER SERVICE If the fax machine is not working as it should, or you want to ask the manufacturers something, call the number indicated on the "Warranty Card".
TECHNICAL GENERAL CHARACTERISTICS Model ........................... Desktop transceiver Display .......................... LCD 16 + 16 char. Capacity memory ......... 360 Kbyte Dimensions Width ............................. 340 mm Depth ............................ 220 mm - 235 mm (**) Height ............................ 133 mm - 272 mm (**) Weight ........................... ca. 2.5 Kg COMMUNICATION CHARACTERISTICS Telephone network ...... Public/private Compatibility .................
INDEX A E Access to the telephone answering device to enable/disable 35 Acoustic signals 56 Automatic document feeder (ADF) 7, 15, 23 Automatic redial 25 ECM (Error Correction Mode) 50 Electrical contacts print cartridge carriage 59 Environment environmental recycling 3 Environmental recycling to dispose of our devices correctly 3 Error codes 53, 54 Error LED indicator 55 B Buzzer volume 50 C I Casing cleaning 61 Cleaning casing 61 electrical contacts 59 optical reader 60 Components external and int
Memos and incoming messages length 37 to delete 38 to listen 38 Messages error messages on the display 55 other messages on the display 56 O Optical reader cleaning 60 Outgoing message 1 to listen 36 to record 35 Outgoing message 2 to erase 36 to listen 36 to record 36 Outgoing messages and memos 35 P Package package contents 8 Paper jammed paper 53 paper has run out 53 plain paper feed compartment (ASF) 7 to feed the print paper 14 to remove jammed sheets of paper 61 Phone book 28 changing a number 28 de
Transmission broadcast transmission 25 sending a document using the quickest method 30 to adjust the contrast and resolution 23 to enable/disable ECM 50 to hear the dialling tone when sending 16, 24 to hear the line signals 49 to regulate the buzzer volume 50 to regulate the speaker volume 50 to send a document 15, 24 to send a document from the memory 25 to send a document with the receiver raised 16, 25 to stop a transmission 24 what documents may be used 15, 23 Troubleshooting minor problems 53 power fai
MANUFACTURER’S CE DECLARATION of CONFORMITY according to EN 45014 OLIVETTI S.p.
ORIGINAL CONSUMABLES Olivetti is the only European company with a proprietary ink-jet printing technology and the original ink-jet consumables are manufactured in its home plant in Italy. The company also produces the non-toxic inks used in the cartridges, based on chemical formulas developed and tested in Olivetti laboratories. The ink is one of the most critical elements in ink-jet printing.
256679S-02
