Table of Contents Safety ......................................................... 5 Specifications ............................................. 4 Assembly .................................................... 5 Maintenance ............................................... 9 Parts List and Diagram .............................. 10 Warranty .................................................... 12 WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol.
Grounding TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use.
. When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Table A.) If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Table A.) Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. 5.
Assembly Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product. Note: Unless stated otherwise, all connections are made using Bolts, Washers and Nuts (B). Finger tighten all connections until assembly is done. Assemble the Workbench on a flat, level, hard surface. 1. Attach Side Beams (4) to Front (1) and Back Posts (2). 4.
7. Attach Front (7F) and Back (7B) Drawer Brackets to Top Beams (6). (See Figure E.) 7B 6 11. Lay Drawer Bottom (13) down on a flat surface. Attach Right (10R) and Left (10L) Drawer Panels to the Front (11) and Back (12) Drawer Panels. Repeat for second Drawer. (See Figure G.) 12. Install the Drawers, making sure the runners on the Drawers are level with the Drawer Mounts. 14 6 7F A A A A 11 12 10L 13 Figure E 8. Attach Middle Drawer Mount (8) to the Front (7F) and Back (7B) Drawer Brackets. 9.
17. Attach Pegboard (18) to Back Upper Posts (15) using Bolts, Washers and Nuts (C). (See Figure I.) 19. Attach Top Shelf (21) to the Shelf Beams (17L, 17R) using Bolts, Washers and Nuts (D). (See Figure K.) D C D D D 17L 21 17R 18 15 15 C C Figure K Figure I 18. Attach Bench Top (19) to Side Beams (4, 4A) and Bottom Shelf (20) to Side Beams (4) using Bolts, Washers and Nuts (D). (See Figure J.
20. Attach Light Fixture (23) to the underside of the Top Shelf (21) using Bolts, Washers and Nuts (G). 21 a. Insert a Bolt through each of the Light Fixture Clips. b. Insert the ends of the Bolts through the holes on the underside of the Top Shelf. Secure with Washers and Nuts on the top of the shelf. G G 23 c. Push Light Fixture up into the Clips. (See Figure L.) Figure L 21. Attach the Light Fixture power cord to the receptacle at the end of the fixture. It will only connect one way.
Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Make sure that the Trigger is in the off-position and unplug the tool from its electrical outlet before performing any procedure in this section. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Assembly Diagram 21 16B 17L 17R 16F 15 15 19 18 4A 4 9L 2 7B 8 7F 6 5 4 9R 2 20 (Under Part 20) 4 1 1 5 13 13 3 12 12 10L 10L 10R 14 11 10R 14 11 Page 11