C500 Series CURRENCY COUNTER USERS GUIDE (Version 1.
FORWARD This Users Guide has been compiled to provide complete instructions for operating the machine. Before starting, please read this document thoroughly to familiarise yourself with all the functions and operations of the unit. Thank you.
1. SAFETY INSTRUCTIONS WARNING! This Currency Counter will start counting automatically under certain circumstances. Consequently, for your safety, it is very important that you always follow these simple precautions:- The machine apply optical sensors.
2. EXTERNAL APPEARANCE (1) Hopper (5) Power Inlet Banknotes to be counted are placed. The Electrical Power Cord should be connected to the power inlet providing a reliable AC power supply. (2) Stacker The counted bank notes are stacked. (6) Fuse holder AC fuse inside. (3) Thickness Adjustment Use the same capacity fuse for replacement. Used to ensure a smooth counting operation. (7) Banknote Guider (4) Power Switch To guide the banknotes in the centre for smooth counting.
(8) Display - ADD key By this key the ADD function is selected, or cleared. LEDs display. (9) Keyboard A set of numerical and multi function keys. Used to preset batch sizes (up to 3 digits) and the detection function. - Code key Use to select the multi function key or the number key. When Code key is ON, the multi function key is selected. And the number key is available when the code key is OFF. (10) Density Indicator Three steps of the density sense. (Refer to page 6 for more information).
3. MACHINE SPECIFICATIONS Ambient Temperature: 0℃~40℃ Ambient Humidity : 30~80% Maximum 200 notes Hopper capacity : Stacker capacity : Maximum 200 notes Size of countable note: 50x100~100x185mm Thickness of countable note: 0.06~0.2mm Batch preset number display : Three Digits LED (small) Counting number display: Four Digits LED (large) AC96V~AC240V,50~60Hz Power source : Power consumption : ≤50W Dimensions : 276mm×238mm×250mm 4.
4. MACHINE OPERATION BEFORE TURN ON THE MACHINE, PLEASE MAKE SURE THE POWER CORD IS GOOD CONNECTION AND PROPER GROUNDING! Turn the Power Switch ON. Ensure the Hopper is empty. Turn the Power Switch ON, the Currency Counter will automatically start running for about 1 Second, (providing no banknote is in the Hopper), upon finishing machine self-diagnostic tests, the machine will show ‘0’ in the 4-digit display area and ‘100’ in the 3-digit display – These show that the machine is ready to begin counting.
Select the Count Mode. This model machine can work in two ways – In ‘Free Count’ mode and ‘Batch Count’ mode. The Count mode can be selected by setting the batch number. - Free Count Mode. In this mode, the machine counts all notes in the Hopper without stopping. This count mode will be set in case the 'blank' is selected on the Batch Number Display by pressing the “C” Key. - Batch Count Mode. In this mode, the machine counts out a batch of notes that you have preset.
If the Ec (Chain) or the Ed (Double) Error message occurs frequently, slowly and carefully turn the Thickness Adjustment Screw in a counter-clockwise direction (loosen). If the feeding operation does not go smoothly, slowly and carefully turn the Thickness Adjustment Screw clockwise (tighten). Counterfeit Detection Functions (Optional). Throughout these optional detection functions, the machine will stop when a counterfeit note is detected. Ultraviolet (UV) Detection Function (Optional).
MG Detection, press the MG key once again, the light will also extinguish. Note: When the machine stops whenever a suspected counterfeit note is detected, take the suspect note out from the Stacker for detailed checking. Press the START key to clear the Error message and recount all of the notes once again. Thread (THD) Detection Function – Euro Currency Only (Optional). The machine can detect suspected counterfeit notes that do not have the correct security thread features.
5. CLEANING AND MAINTENANCE Many of the sensors that applied on this machine are optical devices. These are used to detect the presence of notes in the Hopper, notes in the Stacker, or are used in the bank note counting process. Consequently, paper particles, dust, dirt, etc., may cause miscounting or, in a serious condition, failure of the start-up internal self-testing procedures. Notes: NEVER attempt cleaning the machine when machine is power on.
6. REMOVING THE CAUSE OF ERRORS When an error occurs, an Error Code is shown on the Batch Number Display. Using the Error Code chart below, remove the cause according to the following remedial procedures.
7. ACCESSORIES SUPPLIED Power Cord Users Guide 1 item. 1 booklet. *** In the interests of our ongoing policy of continual product improvement, specifications are subject to change without prior notice.