Digital Camera C-200 ZOOM D-510 ZOOM Reference Manual • Before you use this camera, read this manual and then store it in a safe location where you can find it for future use. • We recommend that you spend some time taking test shots and experimenting with all of the features before you take important pictures.
© Copyright 2001. Olympus Optical Co., Ltd. All rights reserved. Legal and other notices • The contents of this document are subject to change without prior notice. • Although the contents of this document have been carefully checked to avoid errors, some may still occur. If you have a question about any point, or you find mistakes or omissions, please contact us. • No part of this publication may be reproduced or reprinted except for personal use without prior written permission from Olympus.
For Customers in USA Declaration of Conformity Model Number: D-510 ZOOM Trade Name: OLYMPUS Responsible party: Olympus America Inc. Address: 2 Corporate Center Drive, Melville, New York 11747-3157 U.S.A. Telephone number: 631-844-5000 Tested to comply with FCC standards FOR HOME OR OFFICE USE This device complies with Part 15 of the FCC rules.
Contents Features of the C-200 ZOOM/D-510 ZOOM ................................................ VI Using this Manual ........................................................................................ VII Chapter 1 Getting Started ......................................................... 1 Names of Parts .............................................................................................. 2 Attaching the Strap ...................................................................................
Chapter 4 Taking Better Pictures ........................................ 49 Points to Remember .................................................................................... 50 Viewfinder Discrepancies Depending on Distance .................................. 50 Subjects Difficult to Get in Focus ............................................................ 50 When Not Able to Focus on a Subject While Shooting ............................... 52 Determine the Position of the Subject After Focusing .....
Contents (continued) Printing Using DPOF-Compatible Printers or Photo Labs (Print Reserve) ...................................................................................... 109 Rotating Images During Playback (Rotated Playback) .............................. 112 Displaying Image Information on the Monitor (Image Information Display) ................................................................... 113 Changing the Color or Size of Images (Edit) .............................................
V
Features of the C-200 ZOOM /D-510 ZOOM • With its high-resolution CCD (total 2,110,000 pixels) and highperformance lens, the Olympus CAMEDIA digital camera produces pictures of extremely high image quality. • The 3x optical zoom lens and the 3x digital zoom function combine to offer an impressive 9x maximum zoom. • Exposure compensation, spot metering, and other functions are simple using our easy menu operations.
Using this Manual This manual is divided into seven chapters and one appendix which cover the main unit (hereafter called “the camera”). Chapter 1 Getting Started Details confirming the names of all the parts of the camera and preparing the camera to be used for the first time are all explained in this chapter. It is essential to read this before using the camera for the first time.
Appendix You will also find a troubleshooting guide and explanations of the key technical specifications. Additional information The following may appear at the bottom of each page. CAUTION: These sections contain important precautions. Be sure to read. HELP: These sections include information and helpful hints on how to handle problems that may arise during operation. NOTE: These sections contain tips which are good to know in advance.
1 Getting Started This chapter describes the various parts of the camera and their names, the accessories for the camera, and how to prepare the camera to be used for the first time. Please be sure to read this chapter, starting on the following page, before using the camera for the first time.
Names of Parts Camera Shutter button (p.25) Selftimer lamp (p.59) Flash (p.30) Zoom lever (p.31) Lens barrier (p.18) Lens Video OUT jack (p.42) DC-IN jack (p.16) Card cover (p.10) Card slot 2 USB connector (p.
Camera (continued) Arrow pad (p.12) Macro button (p.55)/ Protect button (p.44) Flash mode button (p.64) 1 Getting Started Selftimer button (p.59)/ Erase button (p.45) Diopter adjustment dial (p.15) OK button (p.12)/ Menu button (p.12) Viewfinder (p.50) Monitor (p.28) Battery compartment lock (p.7) Monitor button (p.12) Tripod socket (bottom) Battery compartment cover (bottom) (p.7) Viewfinder Orange lamp (p.30) Green lamp (p.26) AF target mark (p.25, p.
Monitor Shooting mode display Battery check (p.20) AF target mark (p.25, p.52) +1.5 HQ Exposure compensation (p.76) Record mode (p.87) Flash mode (p.64) Spot metering (p.74) Macro (p.55) / Quick focus (p.53) Sequential shooting (p.57) / Selftimer (p.59) / Movie (p.60) White balance (p.85) ISO sensitivity (p.78) ISO100 Memory gauge (p.28) Number of storable pictures (p.21) Playback mode display Battery check (p.20) Print reserve (p.109) Movie (p.107) HQ 2001-01-23 15 4 Protect (p.
Names of Parts (continued) Playback mode display (with image information display on) HQ 1600x1200 Resolution (p.87) 1 Getting Started ISO100 FILE:100-0123 2001-01-23 White balance (p.85) ISO sensitivity (p.78) File number (p.
Attaching the Strap 1 Attach the strap to the camera as shown in the diagram. 2 After passing the strap through the loop, give it a slight tug to make sure that it does not come loose. CAUTION • Attach the strap exactly as shown in the diagram. If the strap is attached incorrectly the camera may come loose and fall off. In this case, Olympus will not be responsible for any damage.
Inserting the Batteries This camera uses four AA (R6) alkaline, NiMH, lithium or NiCd batteries. It can also take two CR-V3 lithium battery packs. Do not use zinc-carbon (manganese) batteries. Do not mix different types of batteries or insert the batteries facing in the wrong direction. As it may overheat and cause irreparable damage to the camera. 2 1 4 1 2 Slide the battery compartment lock from to . 3 Slide the battery compartment cover to the side and lift it up to open.
5 6 5 With the battery compartment cover closed, press the tab and slide it over. • If the battery compartment cover seems hard to close, do not force it. Slide the battery compartment cover toward “OPEN” while pressing down to close. 6 Slide the battery compartment lock from to . CAUTION • The CR-V3 lithium battery packs are not rechargeable. • Make sure that the camera power is off before inserting the batteries. • Alkaline batteries deliver markedly inferior performance, especially in cold weather.
Inserting the Batteries (continued) WARNING Batteries with any part of the outer seal (electrical insulation sheath) peeling off, or any battery split along the seam, can leak, generate heat, or explode. Never use damaged batteries in the camera. Store-bought batteries occasionally may be defective, with all or part of the magnetic insulation sheath peeling off. Never use batteries in this condition.
Inserting the SmartMedia Card Always insert a SmartMedia card (hereafter called “card”) before taking pictures. 1 Make sure the power is off. 2 • The lens barrier must be closed. • Make sure the monitor is off. 2 Open the card cover. 3 Insert the card as shown in the diagram, making sure that it is pushed all the way in. 4 Close the card cover so it clicks into place. • If the card cover is not properly closed, the camera will not turn on.
Using the Card Card Basics What is SmartMedia? SmartMedia is the type of memory card this camera uses. Images recorded and stored on SmartMedia can easily be deleted, overwritten, and/or edited on a PC. Compatible SmartMedia cards 1 Contact area The area where the card comes into contact with the camera. Write-protect area Attach the provided write-protect seal when you want to protect your data from accidental erasure or overwriting.
Setting the Date and Time Time and date information for each picture are recorded at the same time the picture is taken. Therefore, before taking pictures, be sure to confirm that the date and time settings are correct. 3 4 2 1 1 Make sure the lens barrier is closed and SmartMedia is inserted (p.10), then press the monitor button ( ). • When a new card is inserted into the camera, the message “NO PICTURE” will be displayed on the monitor.
5 Monitor (Date setting screen) M–D–Y 01–23–2001 12:00 SET OK 5 6 8 9 Monitor (Date setting screen) 6 Press or on the arrow pad to set the first date/time position (in this case the month 01), then press . • The indicator moves to the next date/time position. • Pressing returns the display to the setting one step earlier. 7 Repeat step 6 until both date and time have been set. 8 When the setting is completed, press the OK button.
Setting the Date and Time (continued) NOTE • Until you change it, the date setting will remain current even when the power is turned off. • It is possible to set the time even when the lens barrier is open and the camera is in shooting mode (p.70).
Adjusting the Viewfinder To make the camera easier to use, adjust the viewfinder to match the eyesight (visual acuity) of the person who will be using the camera. 1 Diopter adjustment dial Slide the lens barrier open until it clicks. • The power turns on, the lens extends, and the flash pops up. 2 While looking through the viewfinder, gently turn the diopter adjustment dial. 3 Stop turning the dial when the AF target mark is clearly visible. 4 You are ready to take some pictures. • See Chapter 2.
Using the AC Adapter (sold separately) The camera may be operated on ordinary household current from a wall outlet by using the optional AC adapter (sold separately). The batteries in the camera are not charged even though the AC adapter is connected. CAUTION • Olympus 3V adapter cannot be used with this camera. NOTE AC wall outlet AC adapter connector AC adapter • When in use for long periods of time the AC adapter may heat up slightly. This is normal.
2 Learning the Basics The fastest way to learn to use the camera is simply to start taking pictures with it. This chapter explains turning the camera on, taking still shots, checking how they came out, and turning the camera off. Please have the camera in hand and practice the operations described as you read the following chapter.
Turning the Power On Slide the lens barrier open. Monitor Battery check Record mode HQ 1 Slide the lens barrier open until it clicks. • This turns the power on in shooting mode. • The lens extends and the flash pops up. • The monitor displays the information shown at left. • After a short time, the monitor will go off. • If the card cover is not securely closed, the power is not turned on even if the lens barrier is opened. • To turn off the power, see “Turning the Power Off” (p.34).
Checking the Monitor Is the Card Inserted? If you forget to insert the card, or if there is any other problem with the card, the monitor will display a message. Read the message and correct the problem. When the “NO CARD” error message is displayed: Monitor • The card may not be inserted properly. • Turn the power off (p.34). Then remove and re-insert the card. 2 • Follow the directions on the monitor. For details, see “Error Codes” (p.142).
Checking the Batteries When the monitor is turned on, it displays the estimated remaining battery life. After opening the lens barrier and turning on the power (shooting mode), the monitor will automatically illuminate, display information, and then go off after a short time. lights (and turns off automatically). The batteries are OK and have enough power to take pictures. blinks and other indicators on the monitor are displayed normally. The batteries are low.
Checking the Monitor (continued) Does the Card Have Enough Room for More Pictures? When the power is turned on with the camera in shooting mode, the monitor displays a remaining picture count. When the monitor display has gone out, press the monitor button ( ) to turn the monitor back on (p.28).
Checking the Monitor (continued) HELP • The number of storable stills and the movie length may vary depending on the subject being photographed. • In some cases the number of storable pictures counter may not decrease every time a picture is taken, nor increase when a frame is erased.
Holding the Camera Proper camera technique Hold the camera firmly with both hands, keeping your elbows at your sides. When holding the camera vertically, make sure the flash is on top. Horizontal grip Vertical grip 2 Learning the Basics Incorrect! Keep your fingers and the strap away from the lens and flash. NOTE • Do not subject the lens to physical shocks. • Be careful not to press on the flash.
Shooting Technique Depends on Distance to the Subject Deciding whether to use the viewfinder or the monitor display when shooting depends on the distance between you and your subject. Determine the approximate distance before taking the picture. For normal and long-range photography (from approx. 1.5m (59″) to ∞ (infinity)): We recommend using the viewfinder (p.25). For close-ups (from 0.8m (31″) to approx. 1.
Taking Still Pictures Taking Pictures Using the Viewfinder Half-press Viewfinder 1 Compose the picture inside the viewfinder. AF target mark Orange lamp 2 Press the shutter button halfway down until the green lamp next to the viewfinder lights up (half-press). • The focus and exposure are automatically set. When the lamp is flashing, it indicates that the subject is out of focus. Press the shutter button halfway once more to correct the focus.
Taking Pictures Full-press 3 Shutter button 3 Having half-pressed the shutter button, press it further all the way down (full-press). • Press the shutter button gently. If you press it too hard, the camera will move and blur the shot. • The shot is taken and the camera beeps. • When the orange lamp next to the viewfinder lights, the flash will fire. Also, the green lamp next to the viewfinder blinks for a few moments and then goes off. 4 When the green lamp goes off, you can take another picture.
Taking Still Pictures (continued) HELP • The area of the actual picture will be slightly larger than the shot appears through the viewfinder. • If you switch the beep function off (p.99), the camera will not beep after taking a picture. In this case you must watch the green lamp. If the lamp blinks, the picture was taken successfully. NOTE • The green lamp will blink for as few as 2 seconds and as many as 40 seconds, depending on the record mode.
Taking Pictures Using the Monitor 1 Compose the shot using the monitor. 3 The procedure for taking pictures is the same as when using the viewfinder (p.25, 26). • The memory gauge is illuminated on the monitor. • No further pictures can be taken when the memory gauge is illuminated to indicate that the memory is full. Wait for several seconds until the memory gauge is off before continuing to take pictures. 4 To go off the monitor, press the monitor button.
Taking Still Pictures (continued) HELP • Pictures taken using the monitor take more time to write to the card than those taken when using the optical viewfinder. • A subject taken at an angle may appear grainy on the monitor, but this will not affect the quality of the actual picture. • Vertical lines may appear on the monitor when taking pictures in full sunlight or other brightly-lit areas. These lines will not be visible in the actual picture and do not indicate a camera malfunction.
Taking Still Pictures (continued) Using the Flash to Shoot in Dim Light If lighting conditions are dim enough to require a flash, the orange and green lamps next to the viewfinder will light when the shutter button is pressed halfway down. Pressing the shutter at this time will cause the picture to be taken with the flash. Viewfinder If the orange lamp is Orange lamp blinking If the orange lamp is blinking, it means that the flash is charging.
Enlarging Your Shots (Optical Zoom) Use telephoto (T) to zoom in on a subject so it appears larger. Use wide angle (W) to capture a wider area. Push the zoom lever toward W (Wide angle) to shoot wide-angle shots. Pull the zoom lever toward T (Telephoto) to zoom in. 2 Learning the Basics Viewfinder Monitor HQ Zoom bar T T W W Zoom status HQ T T W W When using the monitor When the zoom lever is activated, the zoom status will be displayed on the zoom bar.
Playing Back Your Still Pictures You can play back any of the pictures you have taken. 2 1 With the camera in shooting mode (the lens barrier open), quickly press the monitor button ( ) twice. • The camera switches to playback mode and the monitor displays the most recent picture taken. • If no pictures have been recorded on the card, the monitor will show “NO PICTURE”. 2 Check other images recorded by rapidly pressing the arrow pad. : Displays the previous image. : Displays the next image.
HELP • Pressing the buttons on the arrow pad for 1 second or more causes different functions to activate (p. 44, 45).
Turning the Power Off 1 1 Close the lens barrier halfway. • Just before the lens barrier comes in contact with the lens, it will make a click that you can feel with your fingers. • Do not push the lens barrier against the lens. • The lens will recess into the camera. 2 2 Wait until the lens fully retracts, then close the lens barrier the rest of the way. • The power is turned off. • Close the lens barrier firmly until a clicking sound is heard.
3 Playing Images Back The previous chapter explained how to take still pictures and check them immediately. Chapter 3 explains how to check all of the pictures you have taken together once you are finished shooting, as well functions like connecting the camera to your television set for convenient playback.
Getting Started Turning the Power On in Playback Mode 1 1 Make sure the lens barrier is closed. 2 Press the monitor button ( ). • The camera turns on in playback mode and the monitor displays the last image taken. • “NO PICTURE” is displayed on the monitor if no pictures have been taken. Any problems with the card are indicated on the monitor (p.19). • The battery check mark blinks when the batteries are running low (p.20).
Turning the Power Off in Playback Mode 1 Press the monitor button ( ). • The monitor display shuts down and the power turns off.
Displaying Images Frame by Frame To display one frame at a time on the monitor, follow the same steps described in “Playing Back Your Still Pictures” in Chapter 2 (p.32). 3 1 Press the monitor button ( ) with the lens barrier closed. • The power turns on in playback mode and the monitor displays the last image taken. 2 Check the images. • The information for the picture being played back is displayed on the monitor.
Displaying All Frames (Index-Display Setting) Multiple images can be displayed on the monitor at once, useful when search through stored images for a specific picture. 2 5 3 4 With the lens barrier closed, push the monitor button ( ). • The power turns on in playback mode and the monitor displays the last image taken. 2 Push the zoom lever toward (Wide angle). • Several frames are displayed, including the currentlyselected picture. • To select the number of frames to be displayed (p.118).
Displaying All Frames (continued) 2 5 4 Press the arrow pad to select a frame displayed on-screen. : To select the frame to the left. : To select the frame to the right. 5 Pull the zoom lever toward (Telephoto). • The monitor displays the fullsized version of the selected image (p.38). • To display the images again in the index-display setting, repeat from step 2. 3 4 1 HELP • Pressing the buttons on the arrow pad for 1 second or more causes different functions to activate (p. 44, 45).
Checking the Focus by Enlarging a Selected Picture (Displaying Close-ups) This function enlarges a selected image. However, if the image is marked with the movie mark ( enlarged for display. 5 3 2 4 With the lens barrier closed, press the monitor button ( ). • The camera turns on in playback mode. The monitor displays the last image taken. 2 Select the picture that you want to display by pressing the arrow pad (p.38~40). 3 Pull the zoom lever toward (Telephoto).
Connecting to a Television Set Images stored on the camera can be displayed on a larger screen by connecting the camera to a television using the included video cable. 2 1 Before connecting, make sure the camera and television power are off, and that the camera lens barrier is closed. 2 Connect the video cable by inserting one end into the video OUT jack on the camera and the other end into the video IN jack on the television. 3 Turn on the television, and set to “video input.
HELP • The camera monitor does not illuminate when the video cable is connected. • Depending on how your television is adjusted, the picture may appear offcenter on the television screen. • Your television may produce a black frame around the picture, which may be undesirable as it also appears if the image is printed using a conventional video printer. • Refer to your TV/VCR instruction manual for information about displaying video images. • Images shown on screen can be saved to a videotape.
To Avoid Accidentally Erasing Pictures You Want to Keep (Image Protection) Use the protection feature to safeguard images you want to keep. Protected pictures will not be erased by One-Frame Erase (p.45) or by All Frames Erase (p.115). The protection setting remains even after the power is turned off. 2 3 1 With the lens barrier closed, press the monitor button ( ). • The camera turns on in playback mode. The monitor displays the last image taken.
One-Frame Erase Erasing unneeded pictures frees storage space for further picturetaking. Storage space increases by an amount equivalent to that taken by the pictures that have been erased. One-frame erase cannot be used when a picture is protected, or a writeprotect seal is on the card. To erase these pictures, you must cancel the protection feature or remove the write-protect seal from the card (The writeprotect seal may not be reused after it has been removed from the card).
One-Frame Erase (continued) CAUTION • Never open the card cover, eject the card, remove the batteries, or disconnect the AC adapter while erasing pictures. Doing so may destroy the image data on the card. HELP • It may take longer to erase when the “print reserve” function (p.109) has been activated on the card. • The number of storable pictures may not increase even after you erase one image from the card.
Possible Printing Methods Images stored on SmartMedia cards can be printed in the following ways. Using DPOF-Compatible Printers or Photo Labs Setting a print order for images you want printed will allow these images to be printed, without needing to specify them, when the SmartMedia card is inserted into a DPOF-compatible printer or taken to a DPOFequipped photo printing lab. However, it is not possible to set an order for the number of prints to be made.
Possible Printing Methods (continued) CAUTION • The P-400/P-330N(E)/P-330 cannot be connected to the camera’s USB connector. • While it is possible to print from the camera through the video OUT jack, printer performance will be suboptimal. HELP • This camera cannot change automatic print information recorded by other DPOF-compatible devices. Please change the automatic print information with the DPOF-compatible device that recorded the information.
4 Taking Better Pictures The arrow pad allows easy setting of focus, flash type, and a number of other convenient functions. This chapter explains functions that will be useful to remember in helping you to take better pictures. Once you’ve taken a few pictures and familiarized yourself with the contents of Chapter 2, browse the following sections to find more information that will help you master the camera’s various features and functions.
Points to Remember Viewfinder Discrepancies Depending on Distance The image as seen through the viewfinder does not always match up with the final picture depending on the distance between the subject and the camera. Viewfinder Picture frame Close-up working range When shooting subjects 1.5m (59″) to ∞, the viewfinder picture frame shows the area that can be shot. However, the picture area will move lower in the viewfinder as you get closer to the subject.
In these situations, first focus your camera on an object that is the same distance from the camera as your subject, then aim back at the subject to take the picture (focus lock: p.52). Alternatively, set the focus on ∞ (quick focus: p.53) before taking the shot. When setting up shots that do not contain vertical lines like as shown in 3, first hold the camera vertically and lock the focus on the subject. Then shift the camera back to the horizontal position and take the picture.
When Not Able to Focus on a Subject While Shooting Determine the Position of the Subject After Focusing Focus Lock If your main subject is not centered inside the AF target mark, use the focus lock feature explained below: Viewfinder Shutter button 1 Open the lens barrier. • The camera turns on in shooting mode. 2 Look through the viewfinder and position the AF target mark on the subject you wish to focus on. 3 Half-press the shutter button so the green lamp next to the viewfinder lights up.
Fixing a Far-Distance Focus Quick Focus The lens can be set for far-distance focus (∞). Use this function when it is difficult to focus on a subject in the background. Quick focus working range Beyond flash working range T W 0.85m 1.3m 1.8m (2.8ft) (4.3ft) (5.9ft) Monitor HQ 6.7m (22ft) 4 Taking Better Pictures 2 3 4 4m (13ft) 1 Open the lens barrier. • The camera turns on in shooting mode. 2 Press on the arrow pad. • The monitor will illuminate.
When Not Able to Focus on a Subject While Shooting (continued) To cancel quick focus Press on the arrow pad several times until the ∞ mark or macro mark ( ) disappears. Quick focus can also be cancelled simply by turning the camera off To retain the quick focus even after the power is turned off, set the clear settings function in the shooting menu to OFF (p.98). However, even when the clear settings function is set to “OFF”, quick focus will be cancelled when a picture is taken.
Taking Close-up Pictures (Macro Mode) Use the macro function to shoot subjects at very close distances.When using the macro function, maintain a distance of about 20 and 80cm (8″ and 31″). Pictures taken outside this range are likely to be out of focus or poorly exposed. Minimum distance: approximately 20cm (8″) Telephoto: If you wish to further enlarge the image, push the zoom lever toward T (telephoto). Monitor is filled by a 8cm (3″) × 6cm (2″) subject.
Taking Close-up Pictures (continued) To cancel the macro mode Press on the arrow pad several times until the macro mark or ∞ mark disappears. The macro mode can also be cancelled simply by turning the camera off To make the camera retain the macro mode even after the power is turned off, set the clear settings function in the shooting menu to OFF (p.98). HELP • Dark shadows may appear when using the flash.
Taking Sequential Shots Using the sequence function, the camera will continue taking a series of up to 45 still shots (When the record mode is set to SQ) for as long as the shutter button remains pressed. This function is useful for shooting fast-moving objects, since among the many shots there are likely to be some that show the subject or action as you wish. 2 3 4 Open the lens barrier. • The camera turns on in shooting mode. 2 Press on the arrow pad.
Taking Sequential Shots (continued) To cancel sequential shooting To cancel sequential shooting, press on the arrow pad several times until the sequence mark, selftimer mark ( ), and movie mark ( ) disappear. Sequential shooting can also be cancelled simply by turning the camera off To make the camera retain sequential shooting even after the power is turned off, set the clear settings function in the shooting menu to OFF (p.98).
Using the Selftimer For when the photographer wants to be in the picture. Using a tripod is highly recommended. Selftimer lamp 1 Secure the camera on the tripod. 2 Open the lens barrier. • The camera turns on in shooting mode. 3 Press ( ) on the arrow pad. • The monitor will illuminate. 4 Press on the arrow pad repeatedly until the selftimer mark is displayed on the monitor. 5 Set up your shot, then full-press the shutter button.
Taking Movie Pictures In addition to still pictures, this camera has the ability to take movie (15 frames/sec.). Take advantage of this feature to capture your subjects in motion. 2 3 4 5 Monitor (When the movie shooting automatically stops) No flash mark HQ Remaining second count Memory gauge 60 1 Open the lens barrier. • The camera turns on in shooting mode. 2 Press on the arrow pad. • The monitor will illuminate.
Memory gauge The gauge level rises as you continue to shoot. If you continue shooting for the maximum continuous movie length (see chart on the next page), the level reaches the top and the camera stops shooting. Remaining second count Indicates the time remaining before the camera must stop shooting. Shooting stops automatically if the count drops to 0. 5 Green lamp Full-press the shutter button again. • The camera will stop movie shooting and the green lamp beside the viewfinder will blink.
Movie picture record mode For movie pictures, there are two modes with different image sizes and resolutions. Movie picture record modes are set with the still picture record mode settings. To change them, first cancel “movie pictures” and enter the still picture record mode to set the desired resolution (p.87). Items on Menu Record Mode Size (no. of pixels) Continuous Movie length HQ 320 × 240 approx. 16 sec. SQ 160 × 120 approx. 70 sec.
Taking Movie Pictures (continued) To cancel movie shooting To cancel movie shooting, press on the arrow pad several times until the movie mark, sequence mark ( ), and selftimer mark ( ) disappear. Movie shooting will be canceled when the power is turned off To make the camera retain movie shooting even after the power is turned off, set the clear settings function in the shooting menu to OFF (p.98).
Using the Flash Switching Between Flash Modes Select the appropriate flash mode according to the shooting conditions. Note that the flash will not operate when shooting sequential shots (p.57), shooting movie pictures (p.60) and taking panoramic shots (p.82). Also, the working range of the flash changes when you operate the zoom lever (p.30). The camera is automatically set to auto-flash mode when the power is turned on.
Flash mode ➔Auto-flash d (no Mark) Red-eye reduction d Fill-in flash d Function/purpose: Automatically fires in lowlight and backlit conditions (p.66). Significantly reduces the red-eye phenomenon (i.e. when the flash causes a subject’s eyes to appear red in the picture) (p.66). Fires regardless of available light (p.67). No flash d Flash does not fire regardless of the lighting conditions. Good for taking photos where flash is prohibited (p.67).
Auto-Flash In auto-flash mode, the flash will automatically fire in lowlight and backlit conditions. Viewfinder AF target mark To fire the flash in a backlit shot, position the subject inside the AF target mark. Red-eye Reduction When shooting people, eyes may appear red. Use the red-eye reduction flash mode to compensate for this phenomenon. Monitor HQ Eyes appear red.
Using the Flash (continued) Fill-in Flash Forces the flash to fire on every shot. Monitor HQ Fill-in flash mark No Flash Use this mode in situations where flash photography is prohibited, such as art museums and live stage performances, or when taking pictures in twilight or of night scenes. Monitor HQ No flash mark The shutter speed automatically slows down to 1/2 second in low-light situations. The use of a tripod is recommended to prevent blurriness caused by camera movement.
Using the Flash (continued) Night Scenes For taking pictures at night, using flash and slow shutter speeds. Monitor HQ Night scene flash mark This setting fires the flash to expose the foreground while the shutter stays open to expose the details in the background. Night Scenes + Red-eye Reduction The combination of these two modes works best for taking pictures of people at night.
5 Advanced Shooting Techniques Useful shooting functions are all made available within the shooting menu. After you’ve familiarized yourself with the use of the shooting menu, consult the following pages describing each of the various functions.
Use of the Shooting Menu Functions of the Shooting Menu The shooting menu allows you to adjust image qualities, change the record mode, and use the various picture-taking functions. The functions contained in the shooting menu are divided into 4 groups. See “Using the Shooting Menu” (p.72) for information on how to operate the shooting menu. Group Item Spot metering mode Purpose Page Exposure is measured at only the center of the subject. 74 Adjusting image brightness.
Settings retained after power is turned off After the power is turned off, some user settings will be retained in the camera’s memory, but others will return to their factory defaults. The chart below shows the available settings from this menu: Group Shooting Item Possible Settings Memory (ESP) SPOT Exposure compensation +2.0 +1.5 +1.0 +0.5 (0) –0.5 –1.0 –1.5 –2.
Using the Shooting Menu 3 4 5 6 7 1 Slide the lens barrier open until it clicks. • This turns power on in shooting mode. 2 Press the menu button ( ). • The shooting menu will be displayed on the monitor. 3 Press or on the arrow pad to change the settings group (Shooting/Image/Card/Settings). • The selected item is highlighted in green. (In the example at left, “Image” group is selected.) • The current setting for each item is indicated in [ ] to the right of each item name.
7 HARD NORMAL SOFT CANCEL SET OK Press or on the arrow pad to highlight the desired setting. • The selected item is highlighted in green. (The example at left shows Sharpness set to “HARD”.) 8 Press the OK button. • The setting is changed and the menu returns to the first screen. 9 Confirm that the new setting is the one you wanted, then press the OK button twice. • The new setting is retained in the memory and the menu goes off.
Spot Metering (Placing Exposure Priority on the Center of the Subject) If a shot is backlit, ordinary photometric settings (digital ESP metering) will make the subject appear too dark. To compensate for this, switch the camera over to the spot metering mode in the shooting menu. This feature is used to obtain the right exposure regardless of backlighting. For operating instructions see “Using the Shooting Menu” (p.72). Shooting Group Menu Items: CAM ESP ] 0.
Shooting in the spot metering mode Viewfinder Look through the viewfinder and position your subject in the center of the AF target mark. 2 Half-press the shutter button so the green lamp next to the viewfinder lights up. • This sets both the focus and the exposure. 3 If you would like to make any changes within the composition, keep the shutter button half-pressed and recompose the shot. When satisfied, full-press the shutter button to take the picture.
Correcting Image Brightness (Exposure Compensation) Exposure is adjusted automatically whenever a picture is taken. The camera can, however, be set for shorter or longer exposure in five increments from –2.0 to +2.0 (increased/decreased by 0.5). If automatic exposure is used, subjects containing a lot of white will appear darker, while subjects containing a lot of black will appear lighter.
Monitor +1.5 HQ The exposure compensation value appears. (±0 does not appear.) Settings return to the default when the power is turned off. When the power is turned off, exposure compensation returns to ± 0. To make the camera retain its settings even after the power is turned off, set the clear settings function in the settings group to OFF (p.98). • When you change the setting, the brightness of the view on the monitor will also change.
ISO Light Sensitivity Level (Setting ISO Sensitivity) This camera can automatically determine the ISO sensitivity level based on the brightness of the subject. However, for certain kinds of pictures it is better to set the ISO sensitivity level manually. For operating instructions see “Using the Shooting Menu” (p.72). Shooting Group Menu Items: CAM ESP ] 0.0 ] ISO AUTO ] DIGITAL ZOOM [ OFF ] PANORAMA [ [ [ CANCEL Press to highlight “ISO”. The setting screen will be displayed.
Monitor HQ ISO100 Switching from “AUTO” makes the ISO sensitivity appear. Settings return to the default when the power is turned off. When the power is turned off, the camera will return to the “AUTO” mode. 5 79 Advanced Shooting Techniques To make the camera retain its settings even after the power is turned off, set the clear settings function in the settings group to OFF (p.98).
Enlarging Shots Even Further (Digital Zoom) If you find that the camera’s normal optical zoom does not provide enough magnification, use the digital zoom function to increase magnification to up to 9x. Within the digital zoom range (3x – 9x), image quality becomes grainy. For operating instructions see “Using the Shooting Menu” (p.72). Shooting Group Menu Items: CAM ESP ] 0.0 ] ISO AUTO ] DIGITAL ZOOM [ OFF ] PANORAMA CANCEL [ [ [ Press to highlight “DIGITAL ZOOM”.
Shooting Using Digital Zoom 2 1 1 Pull the zoom lever to “T” (Telephoto). 2 Position the subject in the frame using the monitor. • 3x will remain in the display in the viewfinder. • Digital zoom funution can not be used when the monitor display is not illuminated. A maximum telephoto zoom of three times (optical zoom) is possible. Settings return to their default values when the camera is turned off. Turning the camera off also turns off the digital zoom function.
Creating Panoramic Pictures (Panorama Function) Using standard Olympus SmartMedia cards also allows you to shoot panoramic shots easily. This function is not available with other brands of cards. With multiple images in which the edges of the subject can be overlapped, it is possible to use CAMEDIA Master to join the images into a single panoramic shot. For operating instructions see “Using the Shooting Menu” (p.72). Shooting Group Menu Items: CAM ESP ] 0.
• The arrow indicating direction in which frames will overlap changes to the selected direction. If this direction is up or down, the boundaries indicating frame overlap will be displayed on the top and bottom edges of the monitor. 2 3 5 3 Take the shot. • Remember the composition of the shot, so that you can correctly line up the next shot. Pay special attention to the portion of the image in the rectangle along the next stitch edge.
Creating Panoramic Pictures (continued) 8 Press the OK button several times until the shooting menu goes off. The camera itself is not equipped to create panoramic shots from overlapping images. Panoramic shots must be pieced together using CAMEDIA Master. Refer to the CAMEDIA Master online help for information on how to create composite images.
Adjusting the Color Tone (White Balance) This camera uses auto white balance to shoot the subject in a naturallooking tone. However, it may sometimes be difficult to get satisfactory results automatically due to lighting or weather conditions. In such cases, change the white balance settings. For operation instructions see “Using the Shooting Menu” (p.72). Image Group Menu Items: PIC WB AUTO HQ [ NORMAL [ NORMAL [ [ Press to highlight “WB”. The setting screen will be displayed.
Adjusting the Tone (continued) Monitor HQ Switching from “AUTO” makes the white balance mark appear. Settings return to the default when the power is turned off. When the power is turned off the camera will return to the “AUTO” mode. To make the camera retain its settings even after the power is turned off, set the clear settings function in the settings group to OFF (p.98).
Picture Preferences: Quality vs. Quantity (Record Mode) The camera offers four different recording modes (resolutions) that can be selected depending on whether you want better image quality or more pictures. Selecting higher image resolutions will result in better quality pictures, while selecting lower image resolutions will enable you to store more images in the camera (p.21). For operating instructions see “Using the Shooting Menu” (p.72).
TIFF 1600x1200 1280x960 1024x768 640x480 CANCEL SET SQ 1280x960 [NORMAL] [ HIGH ] 1024x768 [NORMAL] [ HIGH ] 640x480 [NORMAL] [ HIGH ] OK TIFF allows you to change the number of pixels. CANCEL SET OK SQ allows you to change the number of pixels as well as the compressibility. Monitor HQ Record mode is displayed Tip on selecting a record mode The record mode can be selected depending on how you will be using the picture: • If you want to send the picture attached to an e-mail, select SQ.
Picture Preferences: Quality vs. Quantity (continued) Restrictions when using of high image quality settings Selecting a high resolution setting increases the amount of time you must wait after taking a shot (the green lamp continues to blink longer), increases the length of playback time, and reduces the number of pictures that you can store on a card. The number of pictures you can store on a card is significantly reduced if you select TIFF.
Making Images Sharper (Sharpness) To emphasize the subject’s outlines and contours and make them more distinct and sharp, change the sharpness setting to “HARD”. If you plan to process the images further on a personal computer, it is better to change the sharpness setting to “SOFT”. For operating instructions see “Using the Shooting Menu” (p.72). Image Group Menu Items: PIC WB CANCEL AUTO HQ [ NORMAL [ NORMAL [ [ ] ] ] ] SET Press to highlight “ ”. The setting screen will be displayed.
Shooting Pictures with Strong Contrast (Contrast) If you want to take pictures with strong contrast (more distinction between lighter and darker areas), set the camera’s contrast to “HIGH”. If you intend to process your pictures on a personal computer, it is better to set the camera’s contrast to “LOW”. For operating instructions see “Using the Shooting Menu” (p.72). Image Group Menu Items: PIC WB ] ] ] ] SET Press to highlight “ ”. The setting screen will be displayed.
Shooting Pictures with Strong Contrast (continued) Settings return to the default when the power is turned off. Turning the camera off also resets the contrast to “NORMAL”. To make the camera retain its settings even after the power is turned off, set the clear settings function in the settings group to OFF (p.98).
Confirming Pictures Directly After Shooting (Rec View) If you want to confirm your pictures on the monitor immediately after shooting, without using the playback mode set Rec View to “ON”. This will cause the most recently taken picture to be displayed on the monitor immediately. The Rec View setting remains even after the camera has been turned off. For operating instructions see “Using the Shooting Menu” (p.72).
Confirming Pictures Directly After Shooting (continued) Taking pictures during Rec View playback Even when the monitor is displaying an image during Rec View, it is still possible to shoot as long as the green lamp beside the viewfinder has gone out.
Changing How File Names are Assigned (File Naming) Pictures are stored in the camera’s memory media as files. It is possible to change the rules by which these files are named. This setting remains in memory even after the power is turned off. For operating instructions see “Using the Shooting Menu” (p.72). File names and folder names Image files and folders are named with letters and numbers as follows. The camera automatically assigns file and folder numbers.
Settings Group Menu Items: REC VIEW [ OFF ] FILE [ NAME RESET ] [ RESET ] [ ON ] SET CANCEL Press to highlight “ FILE ”. The setting screen will be displayed. SET Settings: FILE NAME RESET AUTO FILE CANCEL SET OK NAME RESET (Initial setting) When the card is changed, folder and file numbers restart from default setting. Example: Folder No.102 File No. 0005 96 Folder No.100 Card change File No.
Changing How File Names are Assigned (continued) AUTO FILE Folder numbers do not change when changing to a new SmartMedia card. When copying images onto a personal computer by folder, it is possible to collect the copied images into the same folder using Copy command. (However, under the Mac OS, images in old folders will be erased, so please use caution to avoid losing image files you want to keep.
To Retain Settings Even After Power is Turned Off (Clear Settings) If there is a under the memory column of the chart in “Functions of the Shooting Menu” (p.65, p.103) section, the function in question returns to the default setting when the power is turned off. Those items marked with a can be changed and reset to retain the new setting in memory even after the power is turned off (OFF). Also settings can be set by the Playback Menu. For operating instructions see “Using the Shooting Menu” (p.72).
Turning Off Warning Sounds (Beep Sound) When shooting weddings or for wildlife shots, the camera warning sounds can be a liability. In such cases, the beep sound can be set to “OFF”. This setting remains in memory even after the power is turned off. Also settings can be set by the Playback Menu. For operating instructions see “Using the Shooting Menu” (p.72). Settings Group Menu Items: REC VIEW [ OFF ] FILE [ NAME RESET ] [ RESET ] [ ON ] SET 5 Settings: OFF: The warning beep does not sound.
To Adjust Monitor Brightness (Monitor Adjustment) The brightness of the monitor can be adjusted. This setting remains in the camera memory even after the power is turned off. The same function is also available in the playback mode. For operating instructions see “Using the Shooting Menu” (p.72). Settings Group Menu Items: REC VIEW [ OFF ] FILE [ NAME RESET ] [ RESET ] [ ON ] SET CANCEL Press to highlight “ ”. The setting screen will be displayed.
6 Advanced Playback Techniques The playback menu is used for playback functions including playing movie pictures stored in the camera and playing stored images in order. After you’ve familiarized yourself with use of the playback menu, consult the following pages describing each of the various functions.
Use of the Playback Menu Functions of the Playback Menu The playback menu is used for playback functions including automatically playing images in order and playing movie pictures stored in the camera. See “Using the Playback Menu” (p.104) for information on how to operate the playback menu. Group Item Automatic playback* (Slide show) Purpose Allows images to be played back in order automatically. Allows movie pictures to be played back.
Settings after power is turned off After the power is turned off, some user settings will be retained in the camera’s memory, but others will return to their factory defaults.
Using the Playback Menu 3 4 5 6 7 1 With the lens barrier closed, push the monitor button ( ). • The power turns on in playback mode and the monitor displays the last image taken. 2 Press the menu button ( ). • The playback menu will be displayed on the monitor. 3 Press or on the arrow pad to change the settings group (Playback/Card/Settings). • The selected item is highlighted in green. (In the example at left, “Settings group” is selected.
7 Press on the arrow pad. • The possible settings for that item are displayed. 7 Press or on the arrow pad to highlight the desired setting. • The selected item is highlighted in green. (The example at left shows the Index Display setting set to “16”.) 8 Press the OK button. • The setting is changed and the menu returns to the first screen. 9 Press the OK button twice. • The new setting is recorded in the memory and the menu goes off.
To Play Back Still Images One by One (Automatic Playback) Images (the first frames of movie pictures) are automatically played back in order. This is useful for reviewing images in sequence. Before displaying the playback menu, be sure to display an image that does not have the movie ( ) mark. For operating instructions see “Using the Playback Menu” (p.104). Playback Group Menu Items: PLAY ROTATE [ OFF ] INFO EDIT CANCEL Press the OK button to highlight “ ”. Automatic playback will begin.
To Play Back Movie Pictures (Movie Playback) When playing back movie pictures, before going to the playback menu, the images with the movie “ ” mark that you would like to play back have to be displayed. For operating instructions see “Using the Playback Menu” (p.104). First, display the image with the movie “ ” mark that you would like to playback, and then go to the playback menu (p.102).
To Play Back Movie Pictures (continued) To play back different movie picture Close the playback menu once, select the movie picture you want to play, then display the playback menu once more. For C-200 ZOOM models sold in the PAL color system regions. Play back pictures under the same conditions that they were taken. Movies shot at the normal frame rate (15 frames/sec.) are played back on the monitor at the same rate. Movies are played back at 12.5 frames/sec.
Printing Using DPOF-Compatible Printers or Photo Labs (Print Reserve) DPOF allows you to specify in advance which images you want printed by a dedicated printer, DPOF-compatible printer or DPOF-equipped photo lab (p.47). However, it is not possible to set a print reserve for images that have the movie ( ) mark. For operating instructions see “Using the Playback Menu” (p.104). First, display the image that you would like to set a print reserve, and then go to the playback menu.
3 CANCEL 110 Press on the arrow pad. • The print reserve/print cancel screen is displayed. 3 Press or on the arrow pad to select 1-frame reserve, then press . 1-frame reserve The image you want to reserve printing for can be selected. All-frame reserve Printing can be ordered for all images. Reserve cancel Printing can be cancelled for all images. • A screen allowing you to select images is displayed. 4 The zoom lever may be pushed toward (wide angle) as necessary to see a list display.
Printing Using DPOF-Compatible Printers or Photo Labs (continued) 7 EXIT OK CANCEL Print reserve mark 7 To cancel print reserve, press on the arrow pad for at least 1 second again until the print reserve mark disappears. 8 Press the OK button. • Print reserve information is recorded on the SmartMedia card and the menu returns to the first screen. To set print reserve for all images In step 3, select all-frame reserve, then press the OK button. Print reserve will be set for all images.
Rotating Images During Playback (Rotated Playback) Images taken with the camera held vertically will normally be displayed on their sides when played back on the monitor. The rotated playback function allows you to rotate such images to the upright position. +90° Rotation Display the image you want to rotate before the Playback Menu is displayed. Protected (p.44) images may not be rotated. This setting is retained for images even after the camera is turned off and on again.
Displaying Image Information on the Monitor (Image Information Display) Information recorded with the image when it was shot can be displayed on the monitor. This information appears 3 seconds after the image appears on the monitor. For operating instructions see “Using the Playback Menu” (p.104). Playback Group Menu Items: PLAY ROTATE [ OFF ] INFO EDIT CANCEL Press to highlight “INFO”. The setting screen will be displayed.
Changing the Color or Size of Images (Edit) This takes images in black and white or sepia tones. Also small images (recorded images at low resolution) may be made. Images that have had their color changed or been changed in size are saved in memory as a new image. The original image is not changed. Display the image you want to edit before the playback menu is displayed. However, protected images cannot be edited (p.44). Also, images on cards that have been locked with a protect seal cannot be edited.
To Erase All Images (Erase All Frames) This erases all the pictures stored on a card. Protected images (p.44), however, will not be erased. For operating instructions see “Using the Playback Menu” (p.104). Card Group Menu Items: Check the contents carefully before erasing : Erases all pictures on the card. CANCEL GO OK : (For details, see p.116.) CAUTION • Never open the card cover, eject the card, remove the batteries or disconnect the AC adapter while erasing pictures.
To Initialize (Format) a Card Using SmartMedia cards by companies other than Olympus, as well as cards formatted on another device including a personal computer, may result in longer image-writing times and decreased storage capacity. Such cards should be reformatted by the camera before use. Using Olympus brand pre-formatted cards is highly recommended. When a card that needs to be formatted is inserted into the camera, the camera will automatically go into formatting mode.
Settings: CARD SETUP : (For details, see p.115.) : This initializes the card. CANCEL GO OK Starting and canceling formatting Select “ ” in card setup screen, then press the OK button. The follwing screen will be displayed: YES: Starts formatting CANCEL 6 NO: Cancels formatting GO OK CAUTION • Once formatting has been started, it can not be canceled part way through.
To Change the Number of Frames Displayed (Index Display) In playback mode, you can press the zoom lever and display the images catalog style. It is also possible to change the number of images that are displayed on the monitor when using the “Index Display.” This setting remains in the camera memory even after the power is turned off. For operating instructions see “Using the Playback Menu” (p.104). Settings Group Menu Items: PLAY [ [ CARD ] 9 RESET ] [ ON ] Press to highlight “ ”.
7 Transferring Your Pictures to a Computer Images can be transferred to a computer in a number of ways. This chapter primarily explains how to do this using the special USB (Universal Serial Bus) cable that comes included with the camera.
Read Before Connecting to a Computer Connecting the camera to a personal computer using the included USB (Universal Serial Bus) cable allows you to transfer images stored on the SmartMedia card installed in the camera to the computer’s hard disk. Using the USB cable to connect the camera and computer may require a computer equipped with a USB connector and certain pieces of supporting software (driver), which will vary (see below) depending on the computer’s operating system.
Do not leave the camera connected for an extended period of time when using the batteries The camera will automatically turn on when it is connected to the computer. Also while it is connected, the camera will not go into standby (power saving) mode. If the battery power becomes insufficient while the computer is uploading or downloading data from the SmartMedia card in the camera, images (image files) on the card could be destroyed or an error with the computer could occur.
Connecting the Camera to a Computer Connecting to a Windows PC If you are using a computer installed with the Windows 98/98SE operating system, install the USB driver during operation using the included software CD. A 1 Make sure the camera’s power is off. 2 Open the camera’s connector cover. 3 3 Insert the end of the USB cable marked “A” into the USB connector on the computer. 4 4 Insert the end of the USB cable marked “B” into the USB connector on the camera.
Under Windows 98/98SE When connecting for the first time, use the included software CD to install the USB driver. Refer to the instructions in “Installing the USB Driver” on the following section. Under Windows 2000/Me When connecting for the first time, the computer will load the USB driver automatically. A message saying that installation has been finished will be displayed. Click the OK button and the message will disappear.
Installing the USB Driver (For Windows 98/98SE users only) 1 1 After connecting the camera to the computer, the computer will recognize the camera as new hardware and the screen shown at left will be displayed. 2 2 Click the [Next] button. 3 3 Confirm that “Search for the best driver for your device, [Recommended].” is selected, then click the [Next] button. 4 4 Place the included software CD in the computer’s CD-ROM drive and wait for a moment.
Connecting the Camera to a Computer (continued) 5 Click the check marks on both “Floppy disk drives” and “CDROM Drive” to remove them from the list. Next, click “Specify a location” and check, then click the [Browse...] button. 6 6 Click [ + ] to open the USB folder, and select the Win98 folder by double clicking on it then press the [OK] button. 7 7 Continue clicking the [OK] buttons until a message informs you that installation is finished.
Connecting the Camera to a Computer (continued) Connecting to a Macintosh Check the version of Mac OS and make sure that if the computer can be connected to the camera (p.120). A 1 Make sure the camera’s power is off. 2 Open the camera’s connector cover. 3 3 Insert the end of the USB cable marked “A” into the USB connector on the computer. 4 4 Insert the end of the USB cable marked “B” into the USB connector on the camera.
Transferring Image Files Transferring Image Files to a Windows PC If the camera and computer are connected correctly, the SmartMedia card inserted in the camera should be displayed in “My Computer” folder. It is then possible to handle the files on the card in the same way you would files on a floppy disk. Connect the camera and computer according to the steps (p.122). 2 Double-click the “My Computer” icon on the desktop to open it. 3 Double-click the “Removable Disk” icon to open it.
Viewfinder Orange lamp • When electronic communication between camera and computer is occurring, for example when copying image files, the orange lamp next to the viewfinder will blink. Image files are stored inside a folder in the “DCIM” folder (generally named “100OLYMP”). In addition, Explorer and other file management software can also be used to handle image files. See the instructions of Windows Help and in the computer’s user manual for more details on copying and moving files.
Transferring Image Files (continued) Transferring Image Files to a Macintosh If the camera and computer are connected correctly, the SmartMedia card inserted in the camera should be displayed on the desktop. It is then possible to handle the files on the card in the same way you would files on the computer’s hard disk. Connect the camera and computer according to the steps (p.126). • The camera’s icon (generally, the “PC untitled” icon) is displayed on the desktop.
Transferring Image Files (continued) Image files are stored inside a folder in the “DCIM” folder (generally named “100OLYMP”). See the instructions in Mac OS Online Help and in the computer’s user manual for more details on copying and moving files. Image files transferred to the computer can be viewed using any software application capable of viewing JPEG-format files, including image processing software (CAMEDIA Master, Photoshop, etc.
Disconnecting the Camera or Removing the SmartMedia Card Disconnecting from a Windows PC In order to prevent computer error, be sure to make the following disconnection preparations before proceeding. • Remove the SmartMedia card from the camera. • Disconnect the camera from the computer (unplug the USB cable). If the computer generates an error, disconnect the USB cable and restart the computer.
When using Windows 2000/Me After performing Step 4 from the previous page, you can remove the card. When disconnecting the USB cable, be sure to take the following steps. 1 Follow the procedures on the previous page. 2 On the taskbar (bottom right of the screen), click the “Remove/Eject Hardware” icon (shown in the circle). • A message will appear indicating that the drive will be stopped. 3 Click on the message.
Disconnecting the Camera or Removing the SmartMedia Card (continued) Disconnecting from a Macintosh When removing the card from the camera or disconnecting the camera (USB cable) from the computer, take the following steps so that a computer error does not occur. If the computer generates an error, disconnect the USB cable and restart the computer. Disconnection Preparations Viewfinder Confirm that the orange lamp beside the viewfinder of the camera is not lit.
Transferring Files Without Using the Camera Using an adapter capable of accepting SmartMedia cards allows image files to be transferred from the camera to a computer without directly connecting the two. Consult your Olympus Customer Support Center for the most up-todate information on the various available devices and products. Computer Conditions Usable Devices Floppy disk adapter FlashPath 3.
Appendix Please read the following pages if you suspect your camera may not be working properly. Information on camera specifications and other details are also explained.
Answers to Frequently Asked Questions Q A How long will the camera batteries last? The alkaline battery included with the camera should be able to take at least 100 pictures (assuming the flash is used for 50% of these), but this is only a rough estimate. Battery life is affected by many variables, such as how often you use the monitor, how often you use the flash, the type of batteries used and environmental conditions.
Q A How should I store the camera? Cameras can be damaged by dust, moisture and salt. Wipe the camera with a slightly damp cloth and dry thoroughly before storing. Do not store with mothballs. Remove the batteries if you do not plan to use the camera for a long period of time.
Troubleshooting (Check before Taking in for Repair) Operating Problems The camera does not work The power is off. ➜ Open the lens barrier and turn on the power. The batteries are loaded incorrectly. ➜ Reload the batteries correctly. The batteries are dead. ➜ Replace with new batteries. The card cover is not properly closed. ➜ Securely close the card cover. The batteries do not work in to cold weather. ➜ Keep the batteries warm before the camera is to be used. • The standby function is on.
The flash does not fire • The flash is not fully opened. ➜ Use your finger to push the flash housing all the way up before resuming use. • The subject is well lit. ➜ Set the flash mode to Fill-in if you want the flash to fire regardless of lighting conditions. The flash does not work with shooting in the sequence, panorama, or movie picture modes. Pictures already taken do not appear on the monitor • The camera is in record mode.
Picture Problems The picture is out of focus • The camera was jarred when the shutter button was pressed. ➜ Hold the camera firmly and press the shutter button smoothly. • The viewfinder AF target mark was not positioned on the subject. ➜ Position the autofocus frame on the subject, or use the focus lock. • The lens is dirty. ➜ Clean the lens with a soft, dry cloth. • The mode was not selected correctly. ➜ Shoot in the macro mode where the subject is within the range of 0.2m (8″) to 0.8m (31″).
Troubleshooting (continued) The colors of pictures taken indoors look unnatural • The lighting affected the picture. ➜ Set the flash to fill-in mode. • The subject is mostly dark. ➜ Use flash or increase exposure compensation +. • The white balance setting is incorrect. ➜ Set the white balance to suit lighting conditions. The picture has obscured edge(s) • The lens was partly blocked by a finger or the strap. ➜ Hold the camera correctly, keeping your fingers and the strap away from the lens.
Error Codes The monitor displays error codes to alert you to various problems. Warning Monitor Display Error Remedy There is no card in the camera. Insert the card. The card is not inserted correctly. Remove and reinsert the card. The card is full. Replace the card, erase unwanted pictures, or transfer the data to a computer and erase all the data to free up space on the card. The camera cannot enter picture, erase or cardformat mode. Remove the write-protect seal before taking any pictures.
Using the Camera with Optional Equipment This camera can be used with the following optional equipment: Printer (P-400/P-200/P-330N(E)) FlashPath PC card adapter SmartMedia SmartMedia reader/writer Camera As of March 2001 143 Appendix Computer TV AC adapter MO drive
Optional Items • Photo Printers For Olympus Digital Cameras (P-400/P-200/P-330N (E)) • AC Adapter • Standard SmartMedia Card (8/16/32/64/128MB) • FlashPath Floppy Disk Adapter • PC Card Adapter • NiMH Batteries • NiMH Battery Charger Set • USB SmartMedia Reader/Writer As of March 2001 Visit the Olympus web site for the latest information on optional items. http://www.olympus.
Compatibility of the Still Picture Data Notes about playback Pictures taken with this camera and recorded on a card can be played back on another Olympus digital camera. However, there are some limitations depending on the playback camera: • Still pictures larger than the maximum picture size available on the playback camera may be displayed as thumbnails. • Pictures played back on a camera with a different picture aspect ratio will have black frames.
Specifications Product type: Digital Camera Image Recording System for shooting and playing back photo images. Still pictures: Digital recording, JPEG, TIFF non-compression DCF compliant/DPOF compliant Movie pictures: QuickTime Motion JPEG compliant Recording medium: 3V (3.3V) SmartMedia card 4MB, 8MB, 16MB, 32MB, 64MB, 128MB No. of storable still 1 shot (TIFF Mode/1600 × 1200 pixels) pictures (8MB card): Approx. 5 shots (SHQ Mode) Approx. 16 shots (HQ Mode) Approx.
Specifications are subject to change without any notice or obligation on the part of the manufacturer. 147 Appendix Battery charging time for flash: Approx. 8 sec. or less (at room temperature with new batteries) Flash working range: W: Approx. 0.2m (8″) ~ 4m (13ft) T: Approx. 0.2m (8″) ~ 2.6m (8.
Glossary of Terms Aperture This is a mechanism for adjusting the amount of light that passes through the lens. Lower values allow more light to pass, while higher values lessen the amount of light. Backlight A light source that is behind the subject. CCD (Charge-coupled Device) A pickup element that converts light passing through the lens into electrical signals. On this camera, light is picked up at 2.11 million points and converted to RGB signals to build a single image.
ISO A method for indicating film speed laid down by the International Organization for Standardization (ISO) (e.g. “ISO100”). Higher ISO values indicate greater sensitivity to light so that images can be exposed even in lowlight conditions. JPEG (Joint Photographic Experts Group) A compression format for color still images. Photographs (images) shot using this camera are recorded onto the SmartMedia card in JPEG format when the Record mode is set to SHQ, HQ or SQ.
Index A AC adapter ................................. 16 All Erase Frames .............. 115, 139 Auto-Flash .................................. 66 Automatic Playback .................. 106 B Backlighting, backlit ................. 66, 67, 74, 140 Battery(-ies) ................... 7, 20, 136 Beep Sound ............................... 99 BLACK & WHITE ...................... 114 C CAMEDIA Master ....... 82, 128, 130 Card ....... 10, 47, 82, 115, 116, 134 Clear Settings .............................
O T One-Frame Erase ............... 45, 139 Optical Zoom .............................. 31 Telephoto ................. 30, 31, 55, 80 W P Panorama (panoramic pictures) .............. 82 Playback Menu ......................... 102 Print Reserve ........................... 109 Printing ............................... 47, 109 Q Warning Sound(s) ...................... 99 White Balance .................... 85, 141 Wide angle (wide-angle) ............... 30, 31, 55 Z Zoom ..............................
http://www.olympus.com OLYMPUS OPTICAL CO., LTD. San-Ei Building, 22-2, Nishi Shinjuku 1-chome, Shinjuku-ku, Tokyo, Japan. (Customer support) Tel. 0426-42-7499 Tokyo OLYMPUS AMERICA INC. Two Corporate Center Drive, Melville, NY 11747-3157, U.S.A. Tel. 631-844-5000 (Technical support) Tel. 1-888-553-4448 (Toll-free for within 30 days of purchase.) Tel. 1-631-844-5520 (After 30 days of purchase, contact this number.) distec@olympus.com OLYMPUS OPTICAL CO. (EUROPA) GMBH.