PT_021_JE.qxd 2004.3.8 7:10 PM ページ31 MEMO Instruction Manual Underwater Case PT-021 For the digital camera CAMEDIA X-350 ■ Thank you for buying the Underwater Case PT-021. ■ Please read this instruction manual carefully and use the product safely and correctly. Please keep this instruction manual for reference after reading it. ■ Wrong use may cause damage to the camera on the inside from water leakage, and repair may not be possible. ■ Before use, perform an advance check as described in this manual.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-1 Introduction WARNING ● Unauthorized copying of this manual in part or in full, except for private use, is prohibited. Unauthorized reproduction is strictly prohibited. ● OLYMPUS CORPORATION shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from unsuitable use of this product. ● OLYMPUS CORPORATION shall not be responsible for damage, lost profits, etc.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-1 Introduction WARNING ● Unauthorized copying of this manual in part or in full, except for private use, is prohibited. Unauthorized reproduction is strictly prohibited. ● OLYMPUS CORPORATION shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from unsuitable use of this product. ● OLYMPUS CORPORATION shall not be responsible for damage, lost profits, etc.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-3 5. Jumping into the water with the Case in your pocket or in your hand, throwing the Case from a boat or ship into the water, and other rough handling may cause water leakage. Please handle with sufficient care, when handing it over from hand to hand etc. 6. If the camera on the inside should become wet because of water leakage etc., immediately wipe off all moisture and confirm the operation. 7. Please remove the O-ring when traveling by air.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-3 5. Jumping into the water with the Case in your pocket or in your hand, throwing the Case from a boat or ship into the water, and other rough handling may cause water leakage. Please handle with sufficient care, when handing it over from hand to hand etc. 6. If the camera on the inside should become wet because of water leakage etc., immediately wipe off all moisture and confirm the operation. 7. Please remove the O-ring when traveling by air.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-5 8. When the O-ring contact surface is pressed strongly from the outside of the Case, or when the Case is twisted, the waterproof function may be lost. Take care not to exert excessive force. 9. Please use the Case after performing the advance test and the final check. 10.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-5 8. When the O-ring contact surface is pressed strongly from the outside of the Case, or when the Case is twisted, the waterproof function may be lost. Take care not to exert excessive force. 9. Please use the Case after performing the advance test and the final check. 10.
PT_021_JE.qxd 2004.3.
PT_021_JE.qxd 2004.3.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-9 1. Preparations Names of the parts Check the contents of the package. Check that all accessories are in the box. Contact your dealer if accessories should be missing or damaged. LCD hood (on the body) Silicone grease Silica gel Case body LCD hood strap Hand strap Lenscap (Check that the O-ring is normal.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-9 1. Preparations Names of the parts Check the contents of the package. Check that all accessories are in the box. Contact your dealer if accessories should be missing or damaged. LCD hood (on the body) Silicone grease Silica gel Case body LCD hood strap Hand strap Lenscap (Check that the O-ring is normal.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-11 Install the strap. How to Press the Shutter Install the strap on the Case body. Installation explanation Finished installation Hand strap When pressing the shutter lever, press it gently, so that there will be no movement of the camera. Hand strap ring CAUTION :Please install the strap correctly as shown above. OLYMPUS CORPORATION shall bear no responsibility for damage etc. caused by dropping the Case because of incorrect installation of the strap.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-11 Install the strap. How to Press the Shutter Install the strap on the Case body. Installation explanation Finished installation Hand strap When pressing the shutter lever, press it gently, so that there will be no movement of the camera. Hand strap ring CAUTION :Please install the strap correctly as shown above. OLYMPUS CORPORATION shall bear no responsibility for damage etc. caused by dropping the Case because of incorrect installation of the strap.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-13 2. Advance Check of the Case 3. Install the digital camera. Advance test before use Check the digital camera. This Case has been the subject of thorough quality control for the parts during the manufacturing process and thorough function inspections during the assembly. In addition, a water pressure test is performed with a water pressure tester for all products to confirm that the performance conforms to the specifications.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-13 2. Advance Check of the Case 3. Install the digital camera. Advance test before use Check the digital camera. This Case has been the subject of thorough quality control for the parts during the manufacturing process and thorough function inspections during the assembly. In addition, a water pressure test is performed with a water pressure tester for all products to confirm that the performance conforms to the specifications.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-15 Loading in the Case Open the Case. Which digital cameras can be loaded? This product (PT-021) is exclusively used for the CAMEDIA X-350. Open the lens barrier. Insert the buckle opener of the accessory into the buckle opening lever as shown in the figure (in direction ①) Pull the buckle opener slowly (in direction ②). When not using the buckle opener, hold the buckle opening lever with your thumb and index finger from the side and pull it up slowly.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-15 Loading in the Case Open the Case. Which digital cameras can be loaded? This product (PT-021) is exclusively used for the CAMEDIA X-350. Open the lens barrier. Insert the buckle opener of the accessory into the buckle opening lever as shown in the figure (in direction ①) Pull the buckle opener slowly (in direction ②). When not using the buckle opener, hold the buckle opening lever with your thumb and index finger from the side and pull it up slowly.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-17 Insertion of silica gel Seal the Case. Before sealing the Case, insert the accessory silica gel bag for prevention of fogging between the bottom of the camera and the Case. Insert the bag with the glued longer side to the inside.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-17 Insertion of silica gel Seal the Case. Before sealing the Case, insert the accessory silica gel bag for prevention of fogging between the bottom of the camera and the Case. Insert the bag with the glued longer side to the inside.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-19 Installation and Removal of the LCD Hood Perform the final checks. Installation Visual Inspection Strongly push the mounting projections of the LCD hood as shown in the figure into the guides above and below the LCD monitor window. After sealing the Case, check the sealing part of front and rear lid visually to confirm that the O-ring is not twisted or out of the groove and that no foreign matter has been caught.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-19 Installation and Removal of the LCD Hood Perform the final checks. Installation Visual Inspection Strongly push the mounting projections of the LCD hood as shown in the figure into the guides above and below the LCD monitor window. After sealing the Case, check the sealing part of front and rear lid visually to confirm that the O-ring is not twisted or out of the groove and that no foreign matter has been caught.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-21 Final Test 4. Taking Pictures Under Water The final test after loading the camera is explained below. This is the only way to eliminate worry about possible entry of water! Always perform this test. It can be performed easily in a water tank or a bathtub. The required time is about five minutes. How to Use the Hand Strap Simple water immersion test Explanatory image Pass your hand through the accessory hand strap and adjust the length with the stop button.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-21 Final Test 4. Taking Pictures Under Water The final test after loading the camera is explained below. This is the only way to eliminate worry about possible entry of water! Always perform this test. It can be performed easily in a water tank or a bathtub. The required time is about five minutes. How to Use the Hand Strap Simple water immersion test Explanatory image Pass your hand through the accessory hand strap and adjust the length with the stop button.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-23 5. Handling After Shooting Take out the digital camera. Open the Case carefully and take out the digital camera. Wipe off any waterdrop. CAUTION : • Always place the opened Case with the O-ring side After completing the shooting and returning to land, wipe off any waterdrop sticking to the Case. Use air or a soft cloth not leaving any fibers to thoroughly wipe any waterdrop etc.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-23 5. Handling After Shooting Take out the digital camera. Open the Case carefully and take out the digital camera. Wipe off any waterdrop. CAUTION : • Always place the opened Case with the O-ring side After completing the shooting and returning to land, wipe off any waterdrop sticking to the Case. Use air or a soft cloth not leaving any fibers to thoroughly wipe any waterdrop etc.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-25 Wash the Case with pure water. 6. Maintaining the Waterproof Function After use, seal the Case again after taking out the camera and wash it sufficiently in pure water as soon as possible. After use in sea water, it is effective to immerse it for a fixed time in pure water to remove any salt. Remove the O-ring. Open the Case and remove the O-ring from the Case.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-25 Wash the Case with pure water. 6. Maintaining the Waterproof Function After use, seal the Case again after taking out the camera and wash it sufficiently in pure water as soon as possible. After use in sea water, it is effective to immerse it for a fixed time in pure water to remove any salt. Remove the O-ring. Open the Case and remove the O-ring from the Case.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-27 CAUTION : • When a mechanical pencil or a similar other sharp CAUTION : • Always perform maintenance of the waterproof object is used to remove the O-ring or to clean the inside of the O-ring groove, the Case and the O-ring may be damaged and water leakage may be caused. • When the O-ring is checked with the fingertips, take care not to stretch the O-ring. • Never use alcohol, thinner, benzene or similar solvents or chemical detergents to clean the O-ring.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-27 CAUTION : • When a mechanical pencil or a similar other sharp CAUTION : • Always perform maintenance of the waterproof object is used to remove the O-ring or to clean the inside of the O-ring groove, the Case and the O-ring may be damaged and water leakage may be caused. • When the O-ring is checked with the fingertips, take care not to stretch the O-ring. • Never use alcohol, thinner, benzene or similar solvents or chemical detergents to clean the O-ring.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-29 7. Appendix Q & A on the use of the PT-021 Q1 : Which digital cameras can be used? Q1 : The PT-021 is only for the models X-350. Q2 : What cautions must be observed when loading the digital camera into the Case? A2 : Pay special attention to the following items when loading the camera into the Case. (1) Check that the remaining capacity of the battery in the digital camera is sufficient.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-29 7. Appendix Q & A on the use of the PT-021 Q1 : Which digital cameras can be used? Q1 : The PT-021 is only for the models X-350. Q2 : What cautions must be observed when loading the digital camera into the Case? A2 : Pay special attention to the following items when loading the camera into the Case. (1) Check that the remaining capacity of the battery in the digital camera is sufficient.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-31 temperatures or direct sunlight may cause deformation, discoloration or breakage of the Case and deterioration of the Oring. Wipe the inside of the Case with a soft cloth not causing any fibers. Remove the O-ring, wipe off any salt, sand, dust, etc., and also clean the O-ring groove and the O-ring contact surface in the same way and then dry them.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-31 temperatures or direct sunlight may cause deformation, discoloration or breakage of the Case and deterioration of the Oring. Wipe the inside of the Case with a soft cloth not causing any fibers. Remove the O-ring, wipe off any salt, sand, dust, etc., and also clean the O-ring groove and the O-ring contact surface in the same way and then dry them.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-33 with pure water is sufficient. • Do not use commercial defogging agents. Always use the original Olympus defogging silica gel. • Do not use adhesive for repairs or other purposes. When repair is required, please contact a service station of OLYMPUS CORPORATION or your dealer. Q11 : Please tell me about repairs. A11 : Please contact a service station of OLYMPUS CORPORATION or your dealer, if repair should be necessary.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-33 with pure water is sufficient. • Do not use commercial defogging agents. Always use the original Olympus defogging silica gel. • Do not use adhesive for repairs or other purposes. When repair is required, please contact a service station of OLYMPUS CORPORATION or your dealer. Q11 : Please tell me about repairs. A11 : Please contact a service station of OLYMPUS CORPORATION or your dealer, if repair should be necessary.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-35 Specifications Available models Olympus digital camera CAMEDIA X-350 Pressure resistance Main materials MEMO Depth of up to 40 m Body: Transparent polycarbonate Buckles: Stainless steel Grip/Shutter lever: Red polycarbonate Lens window: FL glass Lens ring: Aluminum Operation buttons: Stainless steel Nickel-plated brass Dimensions Width 148 mm x height 102.
PT_021_JE.qxd 2004.3.8 7:10 PM ページE-35 Specifications Available models Olympus digital camera CAMEDIA X-350 Pressure resistance Main materials MEMO Depth of up to 40 m Body: Transparent polycarbonate Buckles: Stainless steel Grip/Shutter lever: Red polycarbonate Lens window: FL glass Lens ring: Aluminum Operation buttons: Stainless steel Nickel-plated brass Dimensions Width 148 mm x height 102.