oo J myo @ INDEX PRODUCT OUTLINE DISASSEMBLY AND ASSEMBLY PROCEDURE ADJUSTMENT METHOD REPAIR PROCEDURES NOTICE OF MODIFICATION APPLICATION LIST OF GREASE AND CHEMICALS SPECIAL JIGS AND TOOLS DESCRIPTION OF MECHANISM OTHERS OLYMPUS OPTICAL COL LTD.
A. PRODUCT OUTLINE House code Type... Finder... Exposure control... Film feed .. . Others... Shutter release... Curtain speed Battery check voltage Exposure specification .. Flange back... Finder-dirt specification Current consumption... Restrictions...
MDK House code Product name Date of sales Type Picture size Film Lens mount Finder Focusing screen Standard diddler Field of view ratio Magnification Finder display Mirror Prism | Exposure control Homely system Photometer range Exposure control system Start of displaying Film sensitivity MOK OM-2000 {uniform name throughout the world) July, 1897.
Shutter dope Shutter speed Flash synchronized Release system Release button Selim-timer Film feed Film load Film wind Film rewind Film counter Multi exposure Others Rear cover Flash contact Tripod screw Power supplies Battery check Quality of the maternal Size Weight MDK Mechanical focal plane huller, vertical type, 8.1. 1/2000 sec { impossible to use middies speed). BLUE 115 180 180 1/125, 1/280, 1/500 1/1000 12000 (Bec) 11125 sec or slow.
MDK Shutter release Stroke mounting LED lights on. Stroke from LED on to Sutler fire. Space between shutter fire and Release button's end should mote Curtain speed 5816.1 ms at 1/1000 Shutter speed Standard unit ms Speeds Standard values Specifications 1 1000 732~1366 12 500 AB6~BE3 1/4 250 | 183-342 118 125 G1 5-171 | 118 6286 | 45 B~864 1/30 a2 228~427 160 156 114~214 | 14125 | 781 781-1108 | 1/250 | 3.81 258~582 1500 185 128~208 11000 | nay | 058~184 1/2000 0.
Exposure specification Specification MOK 0 — : Exposure over (+1 DEV or more) ge)— : Exposure over (P0.25EV to +1 DEV) eh bet Proper exposure (+40 26EY) a : Exposure under (-02510 -1 DEV) op em . Exposure under {1 OEY or more) indication wv FNo | SS | remittances | %1SO100 Lv £56 1/15 mosey | “Both average and Spot LV rea 160 LO EEY F Measurement is performed near LVOV Fs6 | 1/1000 +0 SEV green LED.
MOK Restrictions, {Restrictions for the OM system) 1 Interchangeable lens groups Because the quick-return mirror is smaller than that of former OM system, the use of peephole lens of { = 800mm or more causes vignetting, Because the screen is not interchangeable, the lens which requires the screen to be exchanged does not permit proper shooting.
MOK B.DISASSEMBLY AND ASSEMBLY PROCEDURE [1] Flowchart of disassembly and assembly... Disassembly and assembly procedure 1. Removal and installation of the bottom plate... Ba 2. Removal and installation of the rear cover B-3 3. Removal and installation of the stopover 3-1 Removal and institutionalization Knob .B-3 3-2 Removal and installation of the AS lever... 3-3 Removal and institutionalization Lever oo H-4 24 Removal and institutionalization SD dial... Bd 3-5 Removal and BS 4.
MDK [ 1] Flowchart of disassembly and assembly 334 lever 344 80 dial lever B-3 3 Top cover B-5 1.Bottom plate 4.8 mount Rear cover | 4 Front cover shaft holder B-13 11 Counter B11 6 Focusing screen B.& 13.A5 PCB B13 shaft B-11 x 9 Mirror 10.
MDK [2] Disassembly and assembly procedure 41. Removal and installation of the bottom plate [Disassembly procedure] : {Assembly procedure] 1) Remove four screws and lake off the bottom 1) Install the bottom plate and fasten # with four plate. : s Crews. 2. Removal and installation of the rear cover | Disassembly procedure] [Assembly procedure} 11 Pull put the shaft and remove the rear cover. 11 Fasten the rear cover with the shaft and the wo Two side collars to be removed. i side collars. 3.
MDK Removal and installation of the A lever [Disassembly procedure] i {Assembly procedure] Remove a screw (1 and take off the Al cover 2 : 1) Install the AL cam (1) with its chambered face (Fig-1) : Hide the AL washer 3 and remove il (Fig-2) Remove the AL spring A lever GIRL plate &, : and AL cam 7 (Fig-1) : downward. (Fig-1) Apply grease H-28} fo the upper part of the Al cam (1.
MK 3-5 Removal and installation of the grip [Disassembly procedure] i {Assembly procedure] 13 Peel of the name plate (11 and remove 1) Apply grease (H-2) to the release pin ll, install it two screws © (Fig ll : on the top cover and fasten the top cover with the : four screws 10.
MDK 5. Removal and installation of the M FPC {Disassembly procedure} Unsold er the FPC 1) on the SD unit, and LED | 1) {Assembly procedure] Attach the M EPC to the prism with @ REDUCTIVE) CH | @ Backspin) EOC 2 then remove fen lead wires (3 (Fig) | : double-coated tape. 21 Remove the NM FPC attached to the prism win | 12) Solder ten lead wires (3, then solder the LED double-coated tape. : FRC 2 and FPC I on the SD unit. (Fig) 6.
MDK 7. Removal and installation of the front casting [Disassembly procedure | [Assembly procedure] if the M FPC is not removed, remove four | 1) Set the shutter to * BULB ' and wind-completion, chad wires @ and the FPC (D on the : discharge mirror and diaphragm mechanism. SD unit. (Fig-1) : i2) While feeding the charge pin ii of the SL base into 11 Remove three screws 30 and take off the | the guide 10 of the sel lever (Fig-5), inset the release SD units.
1 8. Removal and installation of the side plate L, side plate R and SL base [Disassembly procedure] Remove three screws | 11: and take off the side plate L The link plate 3 and link spring @ are to be removed {Fig-1) Remove three screws 5 and take off the side | plate REG (Fig 1) Remove thee screws | 7) and take off the SL | base 8.
MDK 8. Removal and installation of the mirror { Disassembly procedure] : [Assembly procedure] 11 While holding the M spring Insert the tin 3 of the M spinning into the rubber @ of the tweezers, slide the M shaft @ until it is mirror and install the mirror on the front casting Fig-1 2) removed and take off the mirror (Fig-1) | 2) Side the M shall (2 to the position pointed by @_ (Fig) Take care not to lose the M spring.
MDR Removal and installation of the shutter {Disassembly procedure] Remove the red wire | on the B ease (Fig 1) Remove a screw (2) and take off the B contact 3 | and Ease 4 (Fig) Remove the C screw 5) and take off the charge lever and charge spring 1 (Fig) Remove the RL screw 8) and take off the release plate 4 (Fig-3) Remove three screws 47 and take off the | shutter 1. (Fig-3) [Assembly procedure] Install the shutter while it is charged, and fasten it with three screws 1001.
MDK 11.
MDK 12. Removal and installation of the sprocket [Disassembly procedure] {Assembly procedure] 1) Remove two screws [121 and take off the ! 1) Ably grease (H.26) to the BT shaft holder Plate 3 : {Fgh The spool gear 1, ST gear ©, ST spring @, and S1 shaft 7 are lo be removed (Fig-1) P21 install the sprocket 1, BT shay holder 40, ard £7 release 8 and fasten them with the screw 8 2) Remove a screw 8 and lake off the 57 release {Fig-2) Man ST shaft hider 0 The sprocket! removed.
hh 2 4 Fig MDK 43. Removal and installation of the R shaft holder and AS PCB [Disassembly procedure] Remove two screws (10 and take off the AS spring 2 and AS base 3. (Fig) key spring 8. AS PCB 7, R shalt holder 8 and R collar 80. (Fig-1) Remove two Il screws and take off the : Kay cover 0, key collar 00, and key plate 1 Fig: : [Assembly procedure] install the key collar 15, key plate 43. and key cover Jb.
MDE C.ADJUSTMENT METHOD B-2 1, maladjustment. . . B2 1-1 Howlomakealigtopeover. BZ 1-2 Compartmentalization 1-3 LED light adjustment { when the luminescence box is set at EVE, 11, and B.3 1-4 LED light adjustment { when the luminescence box is set at EVE, 12 and B33 1.5 LED light adjustment { when the luminescence box is set at EVE, 12 and B33 Release position adjustment... B-4 . BS Maladjustment B-6 Wind adjustment BF Film B&8 Finder focus adjustment... ..
MDK [ 1] Adjustment method 1. LED light adjustment * Use a jig top cover for adjustment to prevent the SPD from voltage variation caused by outside noises and others when doing the adjustment. 1+1 How to make a jig top cover, Cit the fore-side of the projection in the prism on the top cover (Fig 1) 1-2 Preparation for adjustment 1.) Load the camera with batteries. 2.) Solder the lead wire of approx. § om in length to the test-point Ton the MFG.
MOK 1-3 LED light adjustment { when the luminescence box is set at EVE, 11, and Set the photometer mode at average, shutter speed at 1/125, and lens at FA.8 and select 150 100 and then install in the luminescence bok.
MOK 2. Release position adjustment {Check method] Press the release plate slowly so that it goes down approx. § 2 mim after the mirror starts to operate. [Adjustment method] inset a minus driver into the guide hole (1 of the release plate, and go Up and down the tip of the release plate to adjust the mirror start position, Magnified figure CHI S showing portion A 3. 8D click adjustment ¥8D unit must be installed.
BULB adjustment ¥ The top cover and SD unit must be removed. [Check method] 11 Press the release plate slowly and quickly 50 that iris sel without fail at BLUE. 21 Velum the release plate slowly and quickly so that the BULB Is discharged. 4) Return the release plate slowly so that if has space after the 2nd curtain starts operating (after the operation stops). [Adjustment method] Adjustment by bending the 2nd curtain hold lever (1: Wind adjustment [Check method] 13 There must be a gap (A) of approx. 0.
MDK 6. Film counter adjustment [Check method] 1) The counter counts one frame while halfway winding. 21 The counter must not count both just after and just before the winding operation is completed. [Adjustment method] See Disassembly and assembly procedure (B11) 7. Finder focus adjustment [Check method] 11 (stall the jig lens (MS.8018) on the camera and set the collator at 500mm.
MDK EEYORE NOTICE OF MODIFICATION 4 PIL —F3 HR JUL-4-1987 (SUBJECT) | Countermeasure of the P plate FW (DESCRIPTION) BP Feb (SCAB) Fr aq b0—2 0 FRI MA, Stick the P plate (SC 1808) on the bottom of film chamber SC1696 P plate \ Stick the P plate on the bottom of film chamber LECHEROUSLY BARR SORBET) RESIN BITTORRENT | This countermeasure is adopted early production only, Wh (REASON) Delbert BRU ET RE Ta prevent the film on the film rail of the camera, H5%H (PARTS SUPPLY) SEER AVIAN BERLINER DEB, This counter
MOK [ 1] Description of the mechanism 1. Exposure meter interlocking range EVZ to 19(150100) Ranges of shutter speeds interlocking the exposure meter at each film sensitivity are as follows.
MBK 2. Multi exposure While holding the ME lever in the direction of the index until it stops, {urn the winding lever. if the index begins to be concealed, release the ME lever and turn the winding lever unl it stops.
MDK 3. Diaphragm. mirror and shutter operations {Description of mechanism] 13 The operation of the winding lever allows the charge lever to move the charge pin through the set lever, and then the diaphragm and mirror are charged. 2% The release plate pulls down the ratchet lever (2. with the release operation, and which releases the diaphragm plate (3110 operate the Dr lever (41 and activates the diaphragm of the lens.
MDK 4) The mirror goes up and the sutler satchel lever (6 starts operating and activates the huller, 51 After the exposure ends and the 2nd curtain finishes closing, the charge ratchet lever 17) releases the charge pin (1) and returns the mirror and diaphragm.
FOGHORN Ey Nag Ho iad OE Gales zine Aer Aria i i (31 PAA (Eee Xsl wddnpee Wl tim Mr ro Pon ti Sih = 200 gis PAVLOVIAN PINOCCHIO AGAIN Hd NY Add O81 = na LIL heathendom HTT Im Led mes Odd W
v puree id = ~BC1643 WEI 15180 | Pha Tez nee Diluted Welshman IBA EN 2J725800 bo Five : ome lon. EXPLODED PARTS DIAGRAM MODEL HOUSE CODE or UNIT] FIG, OLYMPUS OM-2000 MDK an OLYMPUS OPTICAL COL LTD.
