*PFL-01(E).qxd 03.11.27 3:14 PM ページ 1 (1,1) Instruction Manual Waterproof Case PFL-01 For the electronic flash FL-20 ■ Thank you for buying the Underwater Case PFL-01. ■ Please read this instruction manual carefully and use the product safely and correctly. ■ Please keep this instruction manual for reference after reading it. ■ Wrong use may cause damage to the flash on the inside from water leakage, and repair may not be possible. ■ Before use, perform an advance check as described in this manual.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-1 (1,1) Disclaimer WARNING ● Unauthorised copying of this manual in part or in full, except for private use, is prohibited. Unauthorised reproduction is strictly prohibited. ● OLYMPUS CORPORATION shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from incorrect use of this product. ● OLYMPUS CORPORATION shall not be responsible in any way for damage, lost profits, etc.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-3 (1,1) 5. Rough handling, such as jumping into the water with the case in your hand or in an outside pocket or throwing the case into the water could lead to water penetration. Please always take care when using the case. 6. If the electronic flash contained in the case gets wet, wipe off all moisture immediately and check the flash is working correctly. 7.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-5 (1,1) outside of the Case, or when the Case is twisted, the waterproof function may be lost. Take care not to exert excessive force. 9. Please be sure to perform the advance test and the final test each time before using the case. 10. If you see any drops of water or any other signs of water penetration during use, stop the dive immediately.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-7 (1,1) Contents Disclaimer⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-1 Please read the following before using the product ⋯⋯⋯⋯⋯E-1 For safe use ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-1 Batteries ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-3 For Prevention of Water Leakage Accidents ⋯⋯⋯⋯⋯⋯⋯⋯E-4 Handling the Product ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-5 Contents ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-7-8 1.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-9 (1,1) 1. Preparations Names of the parts Check the contents of the package. Check that all accessories are in the box. Contact your dealer if accessories should be missing or damaged.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-11 (1,1) Preparing the case Connection to the camera case Before shooting, prepare the case as described below. To perform underwater TTL shooting using this case, connect the underwater TTL cable between this case and the camera case. Connect the hot shoe cable (provided with this case) between the TTL cable connector in the camera case and the camera’s hot shoe.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-13 (1,1) 2)Connecting the hot shoe cable Connect the hot shoe cable, provided with this case, between the TTL cable connector on the inner side of the camera case and the hot shoe of the camera.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-15 (1,1) 2. Advance Check of the Case 3. Inserting the electronic flash. Advance test before use Checking the electronic flash This Case has been the subject of thorough quality control for the parts during the manufacturing process and thorough function inspections during the assembly. In addition, a water pressure test is performed with a water pressure tester for all products to confirm that the performance conforms to the specifications.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-17 (1,1) Open the Case. Insertion of silica gel Insert the buckle opener of the accessory into the buckle opening lever as shown in the figure (in direction ) Pull the buckle opener slowly (in direction ). When not using the buckle opener, hold the buckle opening lever with your thumb and index finger from the side and pull it up slowly.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-19 (1,1) Check the loading status. Always perform the following final checks before sealing the Case. Has the electronic flash been inserted properly into the hot shoe of the case? Has the silica gel been inserted all the way at the specified position? Has the O-ring at the Case opening part been installed properly? Are the O-ring and the O-ring contact surface on the front lid free of dirt and other foreign matter? Seal the Case. Perform the final checks.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-21 (1,1) 4. Taking photos underwater Final Test After the electronic flash has been inserted in the case, you should perform the final system check. This covers all tests that you must carry out to make sure that no water can enter the case. The tests are easy to do and only take about 5 minutes. All you need is a bowl or tub of water. ❈The following procedure was originally developed to test for water penetration inside the camera case.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-23 (1,1) 5. Handling After Shooting Wipe off any waterdrop. After underwater shooting, remove any drops of water from the case. Use pressurized air or a soft, lintfree cloth to carefully wipe away any moisture from the hinge between the front and rear lids, the TTL cable connector and the buckles.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-25 (1,1) Disconnecting the TTL cable After making sure that the case and TTL cable are free of water drops, loosen the lock dial screw and disconnect the TTL cable. 6. Maintaining the Waterproof Function Remove the O-ring. Open the Case and remove the O-ring from the Case. Removal of the O-ring Insert the O-ring removal pick between the O-ring and the wall of the O-ring groove. Move the tip of the inserted pick under the O-ring.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-27 (1,1) CAUTION : • When a mechanical pencil or a similar other sharp CAUTION : • Always perform maintenance of the waterproof object is used to remove the O-ring or to clean the inside of the O-ring groove, the Case and the O-ring may be damaged and water leakage may be caused. • When the O-ring is checked with the fingertips, take care not to stretch the O-ring. • Never use alcohol, thinner, benzene or similar solvents or chemicals detergents to clean the O-ring.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-29 (1,1) 7. Appendix operation parts and perform the advance test and the final test. (5) When not using this case, be sure to take the flash out. Q & A on the use of the PFL-01 Q1 : Which electronic flashes can be used with this case? A1 : The PFL-01 case is designed exclusively for the FL-20 Electronic Flash.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-31 (1,1) these modes, refer to the instruction manual for the camera or flash.) Q7: How can I check for water leakage? A7 : Here you should carry out the first check and the final system check with the flash inside the case. It is also recommended that you carry out the first check by diving to the intended depth with the empty case. If this is not possible, this test should be carried out at a depth of at least one meter or in a container of water (e.g.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-33 (1,1) ❈Please contact your dealer or a service station of our company when replacement is required. Replacement will be made against payment. Q13: How can I take good underwater photos? A13: The web page of the visual college of the Club Camedia has a corner for underwater shooting techniques. Please take a look. URL:http://www.olympus-zuiko.com/school/index.html E-33 After-sale Service ● You will receive the Warranty card from your dealer.
*PFL-01(E).qxd 03.11.27 3:14 PM ページ E-35 (1,1) Specifications Available models Olympus digital camera and Electronic Flash (FL-20) Pressure resistance MEMO Depth of up to 40 m Main materials Main body : Transparent polycarbonate Buckle : Stainless steel Buttons, arm mount screw, adapter : Nickel-plated brass Diffuser plate : Acrylic resin Dimensions Width 111.5 mm x height 154.2 mm x thickness 76.