3-865-712-11(1) P-330 Digital color printer Installation Guide • This Installation Guide explains how to install and use the Digital Color Printer P-330 for Windows 95/98, 3.1 and Macintosh software. • Keep this guide handy for future reference and refer to it when requesting service.
Notice for users Program © 1998 Olympus Optical Co., Ltd. All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated or reduced to any machine readable form without prior written approval from Olympus Optical Co., Ltd. IN NO EVENT SHALL OLYMPUS OPTICAL CO., LTD.
Contents For Windows 95/98 (from page 4) System requirements ............................. 4 Installing the software ........................... 5 Uninstalling the software ................ 7 Printing ................................................... 8 Stopping printing .......................... 10 Hints for better printout ................. 11 Setting the resolution ........................... 12 Adjusting the picture quality .............. 13 Making the split print .........................
For Windows 95/98 System requirements Notes • This software is subject to be upgraded without notice. • The pictures used in this manual may be different from the actual screen of the software. Your computer and system software must meet the following minimum requirements to run the printer driver.
Installing the software Install the software containing the printer driver for Windows 95/98 in the supplied CD-ROM. 1 Connect the printer to the computer. See the operating instructions of the Digital Color Printer. 2 Turn on the printer and the computer. Then start Windows 95/98. 3 If the following [New Hardware Found] screen is displayed, check [Do not install a driver] and click [OK]. If the following [Update Device Driver Wizard] screen is displayed, click [Next] and then [Finish].
Notes • When the dialog prompting you to insert the Windows CD-ROM or floppy disk appears during installation, insert the specified CDROM or floppy disk and click [OK]. If the Windows Setup starts after the Windows CDROM is inserted, finish the Setup program. • You can install the software without performing steps 1 through 3. Start Windows 95/98 and then perform steps 4 through 6. If the dialog of step 3 appears after 4 Insert the supplied CD-ROM into the CD-ROM drive.
Uninstalling the software When the driver software becomes unnecessary, remove all the software files from your hard disk as follows: 1 Click the Windows [Start] button, click [Settings], and click [Printers]. The [Printers] dialog appears. 2 Click to select [OLYMPUS P-330]. 3 4 Click [Delete] from the [File] menu. Follow the on screen instructions to remove the OLYMPUS P-330 Printer Driver from your hard disk.
Printing Tip When you print in 306 dpi in the application software, set the picture size up to 1376 x 1024 pixels. 1 Start the application software used to print, and select the image to be printed. 2 Click [Printer Setup] from the [File] menu of the application. The [Print Setup] dialog appears. 3 Set the printer. Note If the message "This printer is not supported by the driver currently associated with it. Windows will use OLYMPUS P-330 instead." appears, click [OK].
4 Click [OK] to close the [Print Setup] dialog. 5 Click [Print] from the [File] menu of the application. The [Print] dialog appears. 6 Set [Copies]. You can set up to 30 copies. You can print continuously using the supplied automatic feeder. The above dialog is of the OLYMPUS C-2.0W95 as an example. The dialog differs depending on the application.
7 Click [OK]. The next dialog appears. For further settings and operations You can make split printing (page 14), adjust resolution (page 12) or picture quality (page 13). Notes on the high speed print mode • Data transmission speed depends on the computer. • If an error occurs, set to 8 Set [Print Mode] to "High speed print mode ON." The data transmission is accelerated. 9 Click [Print]. OFF. Note The printer starts printing.
4 Click the "Document Name" waiting to be printed. 5 Click [Document] in the menu and then click [Cancel Printing]. Refer to the manual of the Windows 95/98 for details. Hints for better printout To obtain better print result, read the application software manual carefully. Changing the resolution and image size are very important. The following information will be useful.
Setting the resolution Maximum picture size • 1376 x 1024 pixels at 306 dpi • 688 x 512 pixels at 153 dpi You can set the resolution depending on the image you print. 1 Tip To print the picture smaller than 688 x 512 pixels, select 153 dpi. The [Print Setup] dialog appears. 2 Set [Printer] to [OLYMPUS P-330], click [Properties] and then click [Graphics]. 3 Set the resolution to 306 dpi or 153 dpi. Printing is performed more quickly. Note 306 dpi is recommended.
Adjusting the picture quality Note If the application software has the same adjustment item as the driver software, do the adjustment on the application software, not on the driver software. If you adjust the same item on both the application software and the driver You can adjust the picture quality of the prints. 1 Click [Print] from the [File] menu of the application, and in the [Print] dialog click [OK]. The [OLYMPUS P-330] dialog appears. 2 Adjust the picture.
Making the split print To make the split print correctly If the application is to print according to the printer's resolution, set the image size as follows: • 688 x 512 pixels in 153 dpi • 1376 x 1024 pixels in 306 dpi See the application's manual for setting the image size. You can make a 2-, 4-, 9-, or 16-split print with an image inset in each split-plane. 1 Click [Print] from the [File] menu of the application, and in the [Print] dialog click [OK]. The [OLYMPUS P-330] dialog appears.
Making multiple prints at high speed To print multiple copies at high speed or with limited hard disk space, check [Print directly to the printer] in the [Spool Settings] window before you start printing. Note You cannot operate the 1 Click [Start]. 2 Point to [Settings] and click [Printers]. 3 Double-click [OLYMPUS P-330] and open the [OLYMPUS P-330] window. 4 Click [Printer] on the menu bar, click [Properties] and click [Details].
For Windows 95/98 7 Check [Print directly to the printer]. 8 Click [OK] and close the [Spool Settings] window. 9 Click [OK] and close the [OLYMPUS P-330 Properties] window.
For Windows 3.1 System requirements Notes • This software is subject to be upgraded without notice. • The pictures used in this manual may be different from the actual screen of the software. Your computer and system software must meet the following minimum requirements to run the printer driver. • IBM PC/AT compatible personal computer Supporting Windows 3.
Installing the software Install the software containing the printer driver for the Windows 3.1 in the supplied CD-ROM. 1 Connect the printer to the computer. See the operating instructions of the Digital Color Printer. 2 Turn on the printer and the computer. Then start the Windows 3.1. 3 Double-click the [Control Panel] icon in the [Main] window. 3 4 Double-click the [Printers] icon. 4 5 Click [Add]. 5 18 For Windows 3.
6 Click [Install]. 7 Insert the supplied CD-ROM. 8 Input "D:\English\Win31" and click [OK]. Input your CD-ROM drive for "D." You can also select from [Browse]. 9 Make sure that "OLYMPUS P-330" is selected and click [OK]. For Windows 3.
Note You cannot print without checking "Fast Printing Direct to Port." 10 Make sure that "OLYMPUS P-330 on LPT1:" is added in the [Installed Printers:] box and click [Connect]. 11 Set [Transmission Retry] to "300," check "Fast Printing Direct to Port," and click [OK]. 12 Click [Close]. Installation finishes. 20 For Windows 3.
Uninstalling the software When the driver software becomes unnecessary, remove all the software files from your hard disk as follows: 1 Double-click the [Control Panel] icon in the [Main] window. 2 Double-click the [Printers] icon in the [Control Panel] window. 3 Click to select "OLYMPUS P-330 on LPT1:" in the [Installed Printers:] box. 4 Click [Remove]. The confirmation window appears. 5 Click [Yes]. For Windows 3.
Printing Tip When you print in 306 dpi in the application software, set the picture size to 1376 x 1024 pixels. 1 Start the application software used to print, and select the image to be printed. 2 Click [Print] from the [File] menu of the application. The [Print] dialog appears. 3 Click [Setup]. The [Print Setup] dialog appears. 4 Notes • Use the set of the print paper and ink ribbon cartridge supplied together in the same carton.
5 Click [OK]. The [Print] dialog appears. 6 Set [Copies]. You can set up to 30 copies. You can print continuously using the supplied automatic feeder. 7 Click [OK]. The next dialog appears. Tip You can make split prints (page 27), set resolution (page 25) or adjust the picture quality (page 26). 8 Click [Print]. The printer starts printing. For Windows 3.
Note If the printing of the data has already started, don't try to cancel printing. Doing so will cause the paper to jam. Stopping printing When a "printing" message is on the screen Click the [Stop] button or the [Cancel] button. The printing is canceled. When the data is in the Print Manager Double-click the [Print Manager] in the [Main] window. Click the "file" waiting to be printed and then click [Delete].
Setting the resolution Maximum picture size • 1376 x 1024 pixels at 306 dpi • 688 x 512 pixels at 153 dpi You can set the resolution depending on the image you print. 1 Tips • To print the picture smaller than 688 x 512 pixels, select 153 dpi. Printing is performed more quickly. • When the application software does not have [Print Quality] setting in the [Print] dialog, click [Options] in the Start the application software used to print, and click [Print] from the [File] menu.
Adjusting the picture quality Note If the application software has the same adjustment item as the driver software, do the adjustment on the application software, not on the driver software. If you adjust the same item on both the application software and the driver software, the image may be printed with You can adjust the picture quality of the prints. 1 Click [Print] from the [File] menu of the application, and in the [Print] dialog click [OK]. The [OLYMPUS P-330] dialog appears.
Making the split print To make the split print correctly If the application is to print according to the printer's resolution, set the image size as follows: • 688 x 512 pixels in 153 dpi • 1376 x 1024 pixels in 306 dpi See the application's manual for setting the image size. Notes • Since the length and breadth ratio of the image does not match that of the paper, the image of the 2-split or 4-split printing is partly cut off.
Making multiple prints at high speed To print multiple copies at high speed or with limited hard disk space, uncheck [Use Print Manager] in the [Printers] dialog before you start printing. 28 For Windows 3.1 1 Double-click [Control Panel] in the [Main] window, and then double-click [Printers] to open the [Printers] dialog. 2 Uncheck [Use Print Manager]. 3 Click [Close] to close the dialog.
For Macintosh System requirements Notes • If an application to increase memory virtually or to accelerate the process speed is installed, this software may not operate properly. • If you use a facsimile modem and set to automatic reception, this software may not operate properly. • If the printer doesn't operate when you connect it to the modem port, connect it to the printer port. This may happen with some Macintosh models which incorporate the modem.
Installing the software Install the software containing the printer driver for the Macintosh in the supplied CD-ROM. 1 Connect the printer to the computer. See the operating instructions of the Digital Color Printer. 2 Turn on the printer and the computer. Then start the Macintosh. 3 Insert the supplied CD-ROM into the CD-ROM drive. 4 Select the software language by double-clicking the corresponding folder. The above screen is an example and may be different from the actual screen.
6 Click [Install]. Installation starts up. 7 When the software is installed successfully, the next screen appears. Click [OK].
Printing 1 Set [Chooser]. Select [Chooser] from the [Apple] menu. The [Chooser] window is displayed. Click the [P-330] icon in the left box. Select the icon in the right box according to the port you connected the printer. When the printer is connected to Click Printer port Printer icon Modem port Modem icon Select [ON] or [OFF] for the [Background Print]. Select To ON Use computer for other work while printing documents. OFF Print at high speed, but cannot use computer for other work.
Tip 3 When you print in 306 dpi in the application software, set the picture size to 1376 x 1024 pixels. Display the [Page setup] dialog in the [File] menu from the application and set the printing conditions. The dialog differs depending on the application software. Paper Click the box and set the print paper while referring to the combinations below. Orientation Select the landscape icon to print a wide image. Select the portrait icon to print a tall image.
5 Display the [Print] dialog in the [File] menu from the application and set the pages and quantity for printing. The dialog differs depending on the application software. Page No. To print all the pages, select [All]. To print the selected pages, input the pages in the boxes to start and end the printing with. Print Qty 6 You can set up to 30 copies. You can print continuously using the supplied automatic feeder. Click [OK]. The printer starts printing. To adjust the picture quality, see page 36.
Stopping printing When a "printing" message is on the screen Click the [Stop] button or the [Cancel] button. Or you may press the period (.) key while holding the command ( ) key down. The printing is canceled. When using the Print Monitor Click the [Cancel] button to cancel printing. If printing has already started You cannot stop printing. Wait until the print paper is outlet. Hints for better printout To obtain better print results, read the application software manual carefully.
Adjusting the picture quality Adjusting the picture quality may result in better printout depending on images. Adjust the picture quality as described below. 36 For Macintosh 1 Display the [Print] dialog in the [File] menu from the application software. 2 Click [Option]. The picture adjust dialog appears.
Note If the application software has the same adjustment 3 Adjust the Color Balance, Sharpness and Density. item as the driver software, do the adjustment on the application software, not on the driver software. If you adjust the same item on both the application software and the driver software, the image may be printed with unexpected result. Color Balance Changes the color balance by adjusting the balance of red, green and blue.
Making the split print Tips • To preview the printed image, see page 39. • You can set [Split] also on the [Preview] screen (page 39). You can make a 2-, 4-, 9-, or 16-split print with an image inset in each split-plane. 1 Display the [Print] dialog in the [File] menu from the application software. 2 Select the desired number of images per sheet in Note The 16-split images printed on the 16-cut sticker are partly cut off due to the size of the sticker.
Previewing the image Previewing function lets you confirm on the monitor screen how the printed image will appear before printing. 1 Display the [Print] dialog in the [File] menu from the application software. 2 Click [Preview]. The preview screen appears. You can also set [Split] and adjust color balance on this screen.
3 Check that the image is placed within the print paper, and click [Print this page] or [Print this page onward]. The printer starts printing. If you click [Print this page onward], the printer prints from the current page through the last page. If you decide not to print the page after previewing Click the [Next page] button to go to the next page if there are more pages. If there are no more pages, previewing is canceled. The dialog closes. To cancel previewing, click the [Cancel] button.
For Windows 95/98/3.1, Macintosh Troubleshooting Use the following measures to solve problems you experience with your printer. If the problem persists, contact your dealer for information on what to do next. The printer prints the image split into pieces. • The resolution of the image is incorrectly set or the size of the image is too large. Edit the image within 306 dpi and 1376 x 1024 pixels or 153 dpi and 688 x 512 pixels. The edges of the printed image are jagged.
• The printer may be malfunctioning. Check the indicators of the printer or the error messages of the computer. If printer does not start printing in 5 minutes after print paper is installed when there is nothing wrong with the printer or computer, turn off the printer and turn it on again. Then try printing again. It may take more than 5 minutes when you set to print many copies. • The hard disk space is not enough. Check the hard disk.
• Paintings, photographs, and books under copyright cannot be duplicated without permission of the copyright holder. • Olympus reserves the right to alter the features and contents of this guide without obligation or advance notice. • Olympus reserves the right to alter the features and contents of this publication of specifications without obligation or advance notice.
3-861-012-11(1) Digital Camera P-300U Digital color printer Instructions •Thank you for purchasing this Olympus digital color printer. • Before using this product, read this manual carefully to ensure correct use.
Owner's Record The model and serial numbers are located at the rear. Record the serial number in the space provided below. Refer to them whenever you call upon your dealer regarding this product. Model No. P-300U Serial No. ________ Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Table of contents Introduction................................................................................ 4 Precautions................................................................................. 4 Safety Precautions ..................................................................... 4 Getting Started Unpacking the printer............................................................. What you can do with the Digital Color Printer P-300U.........................................................
Introduction Precautions Thank you for purchasing this Before using the printer, read the safety OLYMPUS digital color printer. precautions given on pages 4 through 9 and follow them to ensure proper handling. Keep this manual handy for Read this manual and warranty for future reference and use them when requesting service. Make sure that the date of purchase and dealer's name are included on your warranty. future reference.
WARNING If anything strange occurs with the printer, unplug the power cord. If the printer emits smoke, strange smells, or strange sounds, turn off and unplug the printer to prevent fire or electric shock. Then contact Olympus. Should any liquid or foreign object penetrate the printer, unplug the power cord. Do not allow any liquids, metals, or inflammable objects to infiltrate the printer through the vent. This may cause fire or electric shock. Turn off and unplug the printer, and then contact Olympus.
WARNING Do not disassemble or modify the printer. The printer has both hot and high voltage parts on the inside. To prevent an electric shock or printer malfunction, do not attempt to disassemble or modify the printer. For service or repair, contact Olympus. Do not place liquids on the printer. Should any liquid penetrate the printer, it may result in fire or electric shock. Do not place heavy objects on the printer. Doing so may deform the printer cabinet, resulting in fire or electric shock.
WARNING Make sure that excessive dust and foreign matter do not accumulate on the power cord. Dust and foreign matter conduct electricity, which can cause fire and electric shock. If excessive dust and foreign matter accumulate on the cord, unplug the cord and remove them. Immediately unplug the power cord when an electric storm starts outside. The induced electricity from storms may cause fire, electric shock, or printer malfunction. Do not overload the power outlet.
NOTE Do not block the vent. Doing so may cause the printer to heat up, possibly resulting in fire or electric shock. • Do not block the top or side vent. • Do not put the printer in the following places. - Badly-ventilated place - On a soft surface like a rug or bed Do not put the printer on an unstable surface such as a shaky table. If the printer falls out of place, it may injure someone. This may also damage the printer or cause the printer to malfunction.
NOTE Unplug the power cord from the power outlet before cleaning the printer. Accidentally touching a non-user-serviceable part may cause electric shock. Unplug the printer if it is not used for an extended period of time, for example while you are on a long trip. Otherwise, deteriorated insulation or leakage current may cause fire or electric shock. Beware of moisture condensation. Moisture condensation means that water vapor in the air becomes liquid and sticks to the printer surface.
Getting Started Unpacking the printer Make sure that the following accessories are supplied with your printer. • Automatic feeder (1) • Power cord (1) • CD-ROM (for Windows 95, 3.
What you can do with the Digital Color Printer P-300U The Digital Color Printer P-300U enables you to directly print the image you recorded using the OLYMPUS Digital Cameras. By connecting the P-300U to your PC or Macintosh, you can make prints of images from your computer. Direct printing of the image recorded by the OLYMPUS Digital Camera You can print just by pressing the direct print button. (See pages 19 to 25 for the models you can use with P-300U.
Identifying the parts See the pages given in parenthesis for use of the parts. Paper outlet (p. 32) Serial port (p. 19, 22,27) Parallel port (p. 25,26) Power switch (p. 18) AC power connector (p. 18) Direct print button (p. 21,24) Automatic feeder compartment lid (p. 18) READY indicator (p. 19, 22, 25, 28, 30,31) PRINTING indicator (p. 28-31) RIBBON indicator (p. 30, 31) Paper inlet for manual feeding (p. 28) PAPER indicator (p. 30, 31) Cartridge compartment lid (p. 14) Eject lever (p.
Automatic feeder Connecting terminal Window showing number of copies (number of copies) dial (p. 21, 24) Cover (p. 16) Spacer (p. 16) Slide switch (p.
Loading the ink ribbon cartridge Insert the ink ribbon cartridge into the printer. Use only the ink ribbon cartridge supplied with the print paper packed in the same carton. 1 While pressing down the lever, open the cartridge compartment lid. 2 Wind up the ink ribbon to remove the slack. While pressing the center of the reel, wind the ink ribbon in the direction of the arrow. Wind the ribbon until the black line comes to the left edge.
Caution Never put your hand into the cartridge compartment. The thermal head reaches high temperatures, especially after repeated printing. Notes • When installing the ink ribbon cartridge, stand it as illustrated so that dust will not get on the ink ribbon. If the cartridge compartment lid does not close Remove the ink ribbon cartridge, and then reinsert it. To remove the used ink ribbon cartridge Open the cartridge compartment lid and push up the eject lever.
Inserting the print paper You can use the print papers mentioned in "Optional supplies (print packs)" on page 34. First insert the print paper into the supplied automatic feeder, and then install the automatic feeder to the printer. You may insert the print paper directly into the printer. Notes • Insert the print paper with the glaring/shiny side facing up.
• You cannot type on the printing surface; use an 3 To avoid paper jamming, fan the print paper. Make sure not to touch the printing surface oil ink pen to write greetings or other (glaring/shiny side). characters or drawings on the printing surface. • The automatic feeder can hold up to 30 sheets of standard paper or sticker paper. When you add paper to a partially full feeder, be careful that the total number of sheets does not exceed this limit to prevent paper jams.
Inserting the print paper (continued) Installing the automatic feeder to the printer 1 Connect the supplied power cord to the printer, and then to the AC outlet. Power cord (supplied) to the AC outlet 2 Power switch Push the automatic feeder compartment. The lid of the automatic feeder compartment opens. Push the mark. To close the lid, press 3 18 Getting Started until it clicks shut. Insert the automatic feeder firmly into the compartment.
Printing Printing an image recorded by OLYMPUS Digital Cameras You can directly print the image recorded by OLYMPUS Digital Cameras. Printing operation differs depending on the model as described below. DIGITAL VISION D-320L/D-220L/D-220 Digital Cameras Note Before printing, be sure to close the lens barrier of the digital camera. 1 Check that the printer and digital camera are turned off.
Printing an image recorded by OLYMPUS Digital Cameras (continued) 4 Press the LCD ON/OFF button of the digital camera to turn on the playback mode. Control panel LCD ON/OFF button Frame backward and forward buttons 5 20 Printing Select the photo to be printed using the frame backward and forward buttons on the digital camera.
Notes • Press the direct print button only after the image you had selected was displayed. • We recommend using the digital camera with the AC power adapter. • It may take longer to print the photo recorded in HQ mode than other modes of D-320L. To stop continuous printing Set the dial of the automatic feeder to 1. The printer stops after the current printing. Tips • Besides the above standard print, Random print, Multi print, Mirror print, Index print, and Date print are available.
Printing an image recorded by OLYMPUS Digital Cameras (continued) DIGITAL VISION D-300L/D-200L Digital Cameras Note Before printing, be sure to 1 Check that the printer and digital camera are close the lens barrier of the digital camera. 2 turned off. Connect the serial port of the printer to the communication port of the digital camera with the Macintosh connecting cable (supplied). Macintosh | connecting cable (supplied) to communication port 3 to serial port Turn on the printer.
4 Press the LCD ON/OFF button of the digital camera to turn on the playback mode. Control panel LCD ON/OFF button Frame backward and forward buttons 5 Select the photo to be printed using the frame backward and forward buttons on the digital camera.
Printing an image recorded by OLYMPUS Digital Cameras (continued) Notes • Press the direct print button only after the image you had selected 6 Turn the dial of the automatic feeder to set the number of copies to be printed. You can set 1,2, 3,5,10,15 or 30 copies. was displayed. Turn the dial until the desired number appears in the window. Make sure it clicks at that time. Otherwise, you may get the wrong number of copies. When you want to have other number of copies, set the dial to 30.
DIGITAL VISION D-600L/D-500L Digital Cameras 1 2 Check that the printer and digital camera are turned off. Connect the parallel port of the printer to the printer port of the digital camera with the supplied direct print cable. Direct print cable of the parallel type (supplied) Tips • One-sheet print, Index print, Multi print, Mirror print, All print, Random print, and Date print are available. See the instruction manual of the digital camera for details.
Printing an image from the computer To print an image from the computer, first install the supplied printer driver to your computer. 1 Connect to the computer Connect the printer to your computer. Turn off the power to the computer and to the printer before connecting. Notes on connection • Use a shielded printer cable which is shorter To make the connection, also refer to the computer's manual. than 2m. • Connect only one of the serial or parallel cable.
For Macintosh: Connecting to a Macintosh and its compatible If your computer does Use the supplied cable(Mini DIN 8-pin/Mini DIN 8-pin). not match the plug Use a commercialy available cable having a Mini DIN 8-pin plug to connect the printer and a matching plug to connect the computer. (Standard Macintosh serial cable) Note You cannot use the printer and the driver software on a network. Connect the printer directly to the computer.
Printing while directly inserting print paper 1 Send the print command from the computer or digital still camera. The PAPER indicator ( ) is on, and then the READY indicator starts flashing. Left guide Less than 13/16 inches (2 cm) Notes • Align the print paper to the left guide, and insert the print paper straight. • When you insert the paper manually, remove the automatic feeder.
For Your Information Troubleshooting Use the following measures to solve problems you may experience with your printer. If the problem persists, contact your dealer for information on what to do next. • The power is not turned on. Connect the AC power cord to an AC outlet securely. • Cannot remove the ink ribbon cartridge. Turn the printer off then on. After the motor sound stops, try to remove the cartridge. • Printing takes longer than usual.
Troubleshooting (continued) If the indicators are on If you cannot print, check the indicators on the front panel. • The RIBBON indicator is on. The ink ribbon cartridge is not loaded. The ink ribbon has run out. Change the ink ribbon cartridge. The printer will start printing automatically. • The PAPER indicator ( ) is on. No print paper is inserted in the automatic feeder. Remove the automatic feeder from the printer. Insert the print paper and install the automatic feeder to the printer.
• The READY indicator does not light or all indicators are flashing. Print paper is jammed. Remove the jammed paper from the paper outlets on the front and rear panels. Remove the automatic feeder from the printer and see if the paper jammed. • The PRINTING indicator and the PAPER indicator ( ) are flashing. The camera battery is low. Change the battery or use the AC adapter. Turn off the printer and the camera. Then try printing again. • The RIBBON indicator and the PAPER indicator ( ) are flashing.
Troubleshooting (continued) If the print paper is jammed Notes • If the READY indicator does not turn on after having removed the jammed paper, turn the power off and on again. Try printing from the camera or computer again. • If you cannot remove the jammed paper, contact Olympus. If the print paper is jammed, all indicators flash and printing stops. Turn off the power and remove the jammed paper. Remove the jammed paper from the paper outlet on the rear panel Pull out the jammed paper slowly.
Specifications Printer Printing system Effective pixels Printing size Sublimation dye transfer printing (Yellow/Magenta/Cyan 3 pass) 1376 (H) x 1024 (V) dot 4 ½ (H) x 33/8 (V) inches (114 x 85 mm) Gradations 256 levels (8 bits), per color (24 bits) Approx. 16 million colors Printing time (excluding data transmission time) Approx.
Precautions on the ink ribbon cartridge and print paper Notes on storing the ink ribbon cartridge • Avoid placing the cartridge in a location subject to: - high temperatures - high humidity - excessive dust - direct sunlight • When you are going to store a partially-used cartridge for an extended period of time, store it in its original bag.
Sticker (1-cut) set P-60NS1E (Adhesive-label sheets) One ink ribbon cartridge and 60 sheets of 1-cut sticker Sticker (16-cut) set N-60NS16E (Adhesive-label sheets) One ink ribbon cartridge and 60 sheets of 16-cut sticker • IBM PC/AT is a registered trademark of International Business Machines Corporation of the U.S.A. • MS-DOS and Windows are registered trademarks licensed to Microsoft Corporation, registered in the U.S.A. and other countries. • Macintosh is a trademark licensed to Apple Computer Inc.
OLYMPUS OPTICAL CO., LTD. San-Ei Building, 22-2, Nishi Shinjuku 1-chome, Shinjuku-ku, Tokyo, Japan. Tel. 03-3340-2026 OLYMPUS AMERICA INC. Two Corporate Center Drive, Melville, NY 11747-3157, U.S.A. Tel. 516-844-5000 OLYMPUS OPTICAL CO. (EUROPA) GMBH. (Lieferadresse) Wendenstraße 14-16, 20097 Hamburg, Germany. Tel. 040-237730 (Postanschrift) Postfach 10 49 08, 20034 Hamburg, Germany. OLYMPUS OPTICAL CO. (U.K.) LTD.
