INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS Gas Cooktop OCG62X
CONGRATULATIONS Welcome to the Omega Kitchen Community and thank you for choosing one of our many fantastic cooking appliances. We are confident that you will now be able to meet your cooking needs. Before you use the cooktop we strongly recommend that you read though the whole user manual which provides the description of this product and the proper use of its functions.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT: Read the assembly instruction section and safety precautions of this booklet carefully before removing the contents of this carton. 1. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
APPLIANCE DETAILS ULPG 2.75 kPa Gas Type: Burner Pressure: Injector Diameter: Auxiliary Burner Injector Diameter: Semi-Rapid Burners Injector Diameter: Wok Burner Injector Diameter Ø0.55 mm Ø0.70 mm Ø0.98 mm NG 1.00 kPa MJ/hr Rating 4.0 MJ/ hr 6.5 MJ/ hr 13.2 MJ/ hr Injector Diameter Ø0.90 mm Ø1.10 mm Ø1.70 mm MJ/hr Rating 4.0 MJ/ hr 6.2 MJ/ hr 13.5 MJ/ hr Note: The size of the injector diameter is stamped on the front face (e.g. 1.8 for Ø1.80mm injector).
GAS CONNECTIONS LOCAL AUTHORITY REQUIREMENTS Check Gas Type and specifications plate placed on the bottom face of the unit. All gas fitting work, service and repairs can only be performed by an authorized person in accordance with the current edition of AS/NZS5601 and local gas regulations. Failure to comply with this condition will render the warranty invalid. Always unplug the appliance before carrying out any maintenance operations or repairs.
OPERATIONS TO BE PERFORMED WHEN CONVERTING GAS TYPES This operation can only be performed by an authorized person. Remove the gratings and the burner covers; Using a spanner, replace the nozzle injectors “J” (Fig.20) with either Natural Gas sized injectors or LPG sized injectors. REGULATING THE BURNER MINIMUM SETTING When switching from one type of gas to another, the minimum flow rate must also be correct. The flame should not go out even when passing suddenly from maximum to minimum flame.
ELECTRICAL CONNECTIONS LOCAL AUTHORITY REQUIREMENTS Installation is only permitted by an authorized person, and carried out according to instructions provided by the manufacturer. Incorrect installation might cause harm and damage which the manufacturer accepts no responsibility. The electrical connection can be found 40mm in from the rear edge and 390mm from the left hand side (looking from the front). INSTALLATION This cooktop must be connected to a 220-240V 50Hz power supply. It is earthed via the cord.
INSTALLATION IN KITCHEN CABINET WITH DOOR The fixture has to be made according to specific requirements in order to prevent the gas burners from going out, even when the flame is turned down to minimum, due to pressure changes while opening or closing the cupboard doors. When the hob is installed above a cupboard with doors, a separate panel must be installed underneath it. Leave a gap of at least 20 mm clearance between the cooker top and the surface of the panel (fig.
OPERATING INSTRUCTIONS IGNITING THE BURNERS The knob on your gas cooktop controls both ignition and the safety device. Proceed as follows to ignite the burners: Press down & turn the knob for the burner you would like to use. Keep the knob strongly pressed in for approximately 1 second to allow the ignitor to light the gas, and allow the thermocouple to heat up. Release the knob after approximately 1 second. The flame can be adjusted by turning the knob anti clockwise until it reaches the desired size.
WOK BURNER MAINTENACE & ASSEMBLY When fitting the wok burner together, it is very important to check that the burner flame distributor (F) and the cap (C) are correctly positioned (fig. 6). Failure to do so can cause problems with ignition and also the way in which the burner operates. Check that the electrode (S) is always clean to ensure trouble-free sparking. Check that the probe (T) is always clean to ensure correct operation of the safety valves (for models with safety device).
REF: 2018‐04‐12
