INSTRUCTION MANUAL FOR OMEGA FREE-STANDING COOKERS 90x60 cm – OF914FX, OF916FX
READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USING THE APPLIANCE. It is important that you retain these instructions, proof of purchase as well as other important documents about this product for future reference. The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or improper use of the appliance. Due to continual product development, Omega reserves the right to alter specifications and appearances without notice.
WARNINGS: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
LOCAL AUTHORITY REQUIREMENTS Before installation, unpack all parts from carton, remove all internal packaging and check for damage. Check Gas Type and specifications plate placed on the rear of the unit, alternatively there is a second label supplied – this should be fixed in an accessible position close to the appliance (on the side of a cabinet, etc.). All gas fitting work, service and repairs can only be performed by an authorised person in accordance with AS/NZS 5601 and local gas regulations.
IMPORTANT INFORMATION FOR INSTALLING THE APPLIANCE The cooker can be installed separately, a s a freestanding unit, or between kitchen u nits or between a kitchen unit and the wall. This appliance is not connected to devices which exhaust combustion products. Special attention must be focused on the prescriptions described below regarding room aeration and ventilation.
APPLIANCE GAS CONNECTION IMPORTANT: WARNING: This appliance must be installed by an authorised person. DO NOT MODIFY THIS APPLIANCE If the appliance cannot be adjusted to perform correctly, contact the service department. This appliance utilises a threaded 1/2" gas male fitting. To connect the appliance to the gas network with a flexible hose, a supplemental hose nipple fitting is needed which is supplied with the appliance. (Fig. 05). Fig.
TABLE N°1: Energy Consumption Energy consumption Burners Gas type Pressure (kPa) Injector (mm) Mj/hr Auxiliary Natural U-LPG 1.0 2.75 0.90 0.54 4 4 Semi-rapid Natural U-LPG 1.0 2.75 1.18 0.70 7 7 Rapid Natural U-LPG 1.0 2.75 1.55 0.92 12 12 Wok Natural U-LPG 1.0 2.75 1.8 1.02 16 14.8 Watts 3500W Test the operation of the cooker before leaving Note: These burners have no aeration adjustment.
SUPPORT LEGS The cookers are supplied with four transit supports (one for each corner). Four support legs are supplied separately and are fitted on location to the four corners of the lower support frame. Each support leg is pushed over the relevant transit support until flush with the support frame. Each leg is adjusted by screwing the lowe r section in or out as required for fitting to a 900mm bench height.
With the legs adjusted to a nominal cooker height of 910 mm, and the splash-back fitted, anti-tilt restraint bracket can be added to the rear of the appliance. First fit the flat strap to the rear of the cooker at the centre point of the lower rear edge. Use the supplied screw (Fig. 08). Mark a line on the floor marking the mid-point of the cooker once installed (see Fig. 09) from the back wall.
CONVERSION TO DIFFERENT TYPES OF GAS Before performing any maintenance operation, disconnect the appliance from the gas supply and electricity network. REPLACING THE NOZZLES TO OPERATE WITH ANOTHER TYPE OF GAS When converting to LPG remove the NG gas regulator (if fitted) and fit LPG test point adaptor. If converting to Natural Gas, fit gas regulator.
APPLIANCE ELECTRICAL CONNECTION The electric connection must comply with the current legal standards and regulations. Before making the connection, check that: The system electrical rating and the current outlet are adequate for the maximum power output of the appliance (see the label applied to the bottom of the casing). The outlet or the system is equipped with an efficient ground connection in accordance with the current legal standards and regulations.
Three-Phase electric connection The cookers that can also be connected to three-phase systems normally are factory built for the single-phase 230V connection and are supplied with a power cord. Based on the connection system used, install the power cord type indicated in table No.3. To use the selected connection system change the jumpers on the terminal strip as indicated in the diagram of (Fig.15) Fig.
APPLIANCE U S E A N D MAINTENANCE ATTENTION: Important Warnings. For cookers resting on base ATTENTION: if the cooker rest on a base, take the measures necessary to prevent the cooker from sliding along the support base. For cookers with electric ovens ATTENTION: The unit becomes hot during use. Do not touch the heating elements inside the oven. ATTENTION: The accessible parts can become hot during use. Keep children away from the appliance.
Greasing the valves: If it becomes difficult to operate the valve, it should be greased immediately by following the instructions listed below: 1) Disassemble the valve body by loosening the two screws located on the body of the valve (Fig.17) Fig. 17 2) Extract and clean the seal cone and its housing with a cloth. 3) Lightly grease the cone with special grease. 4) Insert the cone, moving it several times, remove it again, remove the excess grease and make sure that the gas passage ways are unobstructed.
USING BURNERS ON COOKTOP A diagram is etched on the control panel above each knob which indicates which burner corresponds to that knob. Manual lighting (it is always possible even when the power is cut off): Turn the control knob that corresponds to the burner selected anticlockwise, setting it to the MAXIMUM position at the etched star (large flame on the control knob (Fig. 18) and hold a lit match to the burner.
USING THE OVEN FUNCTION CONTROL KNOB (Fig. 20) The oven function knob is used to control the electric fan and the oven elements in set combinations in conjunction with the timer and thermostat. The electric oven is heated by 4 elements: a) Upper element (1200W) and grill element (1500W) combined at the top of the oven cavity. b) Lower element (1600W) at the bottom of the oven cavity. c) Two circular elements (1200W) at the rear of the oven cavity, situated around the 2 internal fans.
There are 9 functions as per below: QUICK START/DEFROST FUNCTION: This function runs the rear fans and all elements. The heat generated is too hot to cook in, but is perfect for preheating the oven (run at the required temperature until the thermostat light turns off and on a couple of time, then adjusts to the required function setting. To use as a defrost function, leave the thermostat on 0. This allows air to flow over frozen food speeding up defrost times.
USING THE ELECTRIC OVEN When using the oven for the first time it should be operated for a maximum of 30 minutes at a temperature of about 250°C to eliminate any odours generated by the internal insulation. During normal oven use, select the desired cooking temperature using the thermostat knob and wait until the orange light turns off (set temperature has been reached) before putting in any food. The oven is equipped with 5 guides at different heights (Fig.
USING THE MANUAL TIMER (OF914FX) When not using a timer to cook in the oven, the manual timer control knob should be turned to the manual cooking setting (Hand symbol between 0 and 120). To use the manual timer, place food into the oven and set up functions and temperature as applicable. Adjust the time (from 10 to 120 minutes) by turning the manual timer control knob clockwise until the preferred time is aligned with the index etched on the control panel above it.
Timer function verification A function which has been set is carried out after setting the time required. The “time to run” can be verified at any point by pressing the appropriate function button. Cancelling timer functions A program can be cancelled by selecting the manual function. When a program finishes, it is automatically cancel. CLEANING THE APPLIANCE Before cleaning the appliance, it should be disconnected from the power supply and turned off the main gas feeder valve.
TROUBLESHOOTING If you have a problem with your appliance, check the following before contacting service. PROBLEM Oven or hob not working Hobs ignite but don’t stay on Heating up problems Unit smoking/odours Condensation note: some Condensation is normal and is to be expected during cooking. Oven shelves are tight Cooling fan runs after ovens turns off SOLUTION Check the electricity is turned on. Check your fuses. If the fuse continues to blow, call Omega service. Check the circuit breaker.
21
10
