Instructions for the Use and Care and Installation of ORC97G ORC98G Glass Canopy Rangehoods
CONTENTS 1 Notice 2 Features 3 Installation 4 Notice of installation 5 Safety Warning 6 Use Instructions 7 Maintenance 8 Troubleshooting 9 Specification It is important that you retain these instructions, proof of purchase as well as other important documents about this product for future reference. Due to continual product development, Omega reserves the right to alter specifications or appearances without notice. Dispose of packaging responsibly – recycle where facilities are available.
1 (1) NOTICE 1. Thank you for choosing our cooker hood. Please read the instruction manual carefully before use. 2. The installation work must be undertaken by a qualified electrician and competent installer. 3. The manufacturer disclaims all liability for any damage or injury caused as a result of not following instructions for installation contained in the following text. The cooker hood is rated for use on 220/240V, 50Hz.
2 (2) FEATURES 1. The cooker hood uses high quality materials, and is made with a streamlined design. 2. Equipped with a high power electric motor and centrifugal fan, it produces strong suction with low noise, and features a non stick grease filter which is easy to clean. 3. The isolated low voltage (12 volt) circuit board control, means the halogen lights are brighter and safer than incandescent alternatives. 4.
3 (3) INSTALLATION 1）The cooker hood should be placed at a distance of 65-75cm (26-30inch) from the cooking surface for the best effect. See Pic 1. 2）Install the hook on a suitable place once the installation height is fixed, and keep it in line. The fixed position of the inside chimney bracket is the place of chimney. 3） Fix the extensible pipe according to the lead direction and way, and then put the cooker hood on the hook. See pic 3.
4 (4) NOTICE OF INSTALLATION 1. Before installation, please ensure the area is clean, to avoid suction of the remaining bits of broken wood and dust. 2. The canopy hood cannot share the same air ventilation ducting as other appliances, such as gas and electric heaters. 3. The bending of the ventilation ducting should be ≥ 120°, parallel or above the exit vent, and should be connected through the external wall. 4.
5 (5) SAFETY WARNING Young children should be supervised to ensure that they do not play with the appliance. The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervised or instruction concerning use of the appliance by a responsible person for their safely.
6 (6) USE INSTRUCTIONS The re-usable aluminium grease filters supplied with this rangehood should be cleaned every month or so to avoid grease build-up. To remove the grease filter, release the locking mechanism at the front of the filter, and lower the filter slightly to unhook it at the back. Whilst the filter is removed, clean off any residual grease from the housing to avoid fire risk. When replacing the grease filters, ensure that the locking mechanism is facing down.
7 SPEED ADJUSTMENT - See pictures 1. Push the “Low” button, the indicating light 1 is on, and the motor runs at low speed. Push it again and the motor will stop. 2. Push the “Mid” button, the indicating light 2 is on, and the motor runs at mid speed. Push it again and the motor will stop. 3. Push the “High” button, the indicating light 3 on , and motor runs at high speed. Push it again and the motor will stop 4. Push the light button; the indicating light 4 on, and the two lighting lamps is on.
8 (7) MAINTENANCE 7.1 Cleaning the grease filter mesh The filter mesh is made of high-density stainless steel. Please do not use corrosive detergent on it. Keeping this filter clean will keep the appliance running correctly. Please strictly follow the guidelines below. Method 1: Place the mesh in 40 - 50 DegC clean water, add in a small amount of detergent, and soak for 2 - 3 minutes. Wear gloves, and clean with a soft brush. Do not apply too much pressure, as the mesh is delicate and will damage easily.
G. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
The hanging screw not tight enough Tighten the hanging screw and make it horizontal 10 (9) SPECIFICATION Model Rated Input Rated Power Lighting Power Motor Power Air tube diameter Air output ORC97G 220V-240V, 50Hz 305W 20W X 2 (halogen capsule lamp) 265W 150MM 1000m3/h
11 Model Rated Input Rated Power Lighting Power Motor Power Air tube diameter Air output ORC98G 220V-240V, 50Hz 305W 20W X 2 (halogen capsule lamp) 265W 150MM 1000m3/h 12
